Tiger RBF-19C manual Hedge Trimming, Stalling the Rotor

Page 75

OPERATION

Hedge Trimming

Consider how the job should be tackled before commencing work, as no two hedges have the same height, width, thickness or density of growth. Hedges which have previously been cut by machine tend to have denser growth, and although they can be cut to any desired shape, it is advisable to trim the same shape and height as previous years.

The flails cause the growth to "tiller' and thicken up the hedge. Therefore it is advisable to cut the hedge side at a slight angle rather than straight, otherwise the hedge may eventually die at the bottom due to lack of light.

Below are a few hints on how to tackle a hedge.

A.First trim the top down to previous years's trim in one cut, but do not cut into it, as the old growth will be very thick and strong and cause premature wear to the flail cutting edges.

B.Next trim the sides to the previous trim but not into it.

NOTE: Do not angle the rotor unit so that any debris is thrown through the hedge when trimming the far side of the hedge. Always ensure cut material is directed away from you or on to the ground.

C. Finally, lower the roller and trim along the bottom of the hedge to clear debris and undergrowth.

Stalling the Rotor

If the rotor does become choked the tractor will stall or the relief valve will operate. If this occurs follow the instructions below.

A.Stop forward movement and disengage rotor drive immediately and place PTO drive lever in neutral.

B.Ensure that the rotor has stopped and lift the rotor unit using the hydraulics.

C.Stop tractor engine engage parking brake and wait for all rotation to come to a complete stop.

D.Remove any obstruction that may be present on the rotor. If working under the raised machine ensure that it is safely supported.

E.NEVER UNDER ANY CIRCUMSTANCES run the rotor to "clear itself".

RBF-19C 07/04

Operation Section 4-25

© 2004 Alamo Group Inc.

 

Page 74 Page 76
Image 75
Page 74 Page 76
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Stop Mowing if Passersby are Within 100 Yards UN- Less Equipment Operation Safety Instructions and PracticesSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 See Your Tiger Dealer Parts InformationTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Employer Responsibilities This Act SeeksDuties Osha RegulationsIntroduction Section Before Operating this Machine IntroductionAssembly Section General Tractor RequirementsMachine Preparation Fitting Machine to Tractor Assembly Section Fitting PTOLever Unit Fitting ControlsAdjust Lever Pivot Position Hydraulic SystemsFill Tank with OIL RBF-19C Assembly Section Fitting Rotor Unit Twists Connecting the MotorMechanical Breakout Hose LayoutChafing Hoses Sharp BendsAccumulator KIT Flexible Front Guard KITRBF 19C Assembly Section Initial RUN Bleeding RamsBleeding the First Ram Assembly Page Operation Section Operation Tiger Rear Mount Boom Operation Instructions Connectingattaching HeadsOperation Operator Requirements Tractor RequirementsTractor Requirements and Capabilities Tractor Lighting and SMV Emblem Shatter Proof Safety WindowsRops and Seat Belt Operator Thrown Object ProtectionTractor Ballast Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Dash Nominal Torque Value Size IN.LBS FT.LBS Connecting Attaching Head to the BoomTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service Frame AssemblyBoom ARM Assembly Hydraulic PUMP/OIL Reservoir Hydraulic Line InspectionFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating the Attached Mower Heads Operating Speed and Ground SpeedGrass Flail Roller HeightGround Level and Scrub Cutting lower roller to its maximum Operation Grass Cutting Alternative Rotor Link PositionsStalling the Rotor Hedge TrimmingMotor Position Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head StorageTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section PTO Drive Tubes LubricationGearbox Grease PointsHydraulic Oils Filter ReplacementPower TAKE-OFF Shaft Hoses and Rotor Drive CircuitParking and Removal Rotor UnitHydraulic Cylinders StorageClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents