Woods Equipment TCH4500 manual Assembly Instructions, Dealer SET-UP Instructions

Page 23

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this chipper is the responsibility of the Woods dealer. If should be delivered to the owner completely assembled, lubricated, and adjusted for normal chipping conditions.

Assembly will be easier if parts are aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located in the Bolt Torque Chart, page 35.

Complete check lists on page 27 when you have completed the assembly.

INSTALL 3-POINT HITCH PINS

1.Attach 3-point hitch pins to the chipper frame using nuts and washers supplied with each pin.

2.Torque pins to 474 lbs-ft.

Figure 11. 3-Point Hitch Pin Installed, Left Pin Shown

INSTALL CHIPPER HOPPER

NOTE: Once all parts are installed and aligned torque hardware to specifications listed below.

3/8 NC x 1 . . . . . . . . . . . . . . . 35 lbs-ft (47 N-m) 5/16 NC x 1 . . . . . . . . . . . . . . . 19 lbs-ft (26 N-m) 5/16 NC x 3/4. . . . . . . . . . . . . . 19 lbs-ft (26 N-m)

1.Attach chipper hopper to the chipper housing using four carriage bolts (2), flat washers (1), and lock nuts (3). See Figure 12 and Figure 17.

NOTE: Make sure the heads of the carriage bolts are on the inside of the chute.

3 2 1

DP4

Figure 12. Chute and Hinge Installed

2.Attach rubber flap (8) to the chute flange using flap retainer strap (9), three carriage bolts (12), flat washers (13), and lock nuts (14). Attach lanyard

(10)between the chute flange and washer (13) farthest from the hinge.

12 13 14

9

10

8

DP5

Figure 13. Rubber Flap and Lanyard Installed

MAN0458 (9/23/2005)

Assembly 23

 

 

Image 23
Contents Operators To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsPreparation SafetySafety Rules TrainingTransportation MaintenanceStorage Safety & Instructional Decals SafetyShield Missing Safety Be Careful Attaching Chipper to Tractor OperationOperation Chipper PRE-OPERATIONClearing Plugged Disk Tractor StabilityStarting the Chipper Stopping the ChipperAfter Each Use CleaningOperating Technique Storing ChipperOwners Responsibility PRE-OPERATION Check ListLubrication ServiceService Service and Maintenance ScheduleChipper Blades Install Disk LockBlade Inspection Blade InstallationBlade Servicing Blade Removal & Cutting Edge ReversalFront Drive Belt Drive Belt AdjustmentBlade Clearance Drive BeltRear Drive Belt Front Belt InstallationTroubleshooting TroubleshootingTroubleshooting Install Chipper Hopper AssemblyAssembly Instructions Install 3-POINT Hitch PinsHinge Latch Installed Install Discharge Tube Optional Install SMV SignShorten Driveline Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts TCH4500 Base AssemblyParts TCH4500 Base Assembly Parts ListChipper Upper Assembly TCH4500 Chipper Upper Assembly Parts List TCH4500 Chipper Hopper Assembly TCH4500 Discharge Tube KIT Optional TCH4500 Chipper Hopper Assembly Parts ListTCH4500 & 5000 Chipper Driveline Assembly Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartWarranty Woods Equipment Company