Woods Equipment TBW150C manual Dealer Service, Blade Spindle Repair

Page 24

DEALER SERVICE

The information in this section is written for dealer ser- vice personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in this type of repair, you may be time and money ahead to replace complete assemblies.

„Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

„Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

BLADE SPINDLE REPAIR

Spindle repair requires special skills and tools. If your shop is not properly equipped or your mechanics are not trained in this type of repair, you may be time and money ahead to use a new spindle assembly.

For reference, the grease fitting is in the top of the spin- dle shaft.

Permatex® 3D Aviation Form-A-Gasket or equivalent is recommended as a sealant.

Remove Spindle

1.Remove belt shields from deck.

2.Remove belt.

3.Remove blade from spindle assembly.

4.Remove nuts (6) and bolts (9) that secure spindle to mower. (See Figure 8.)

Disassemble Spindle

1.Remove bolt (1) and washer (2) from the top of the spindle.

2.Remove sheave (3) and spacer (4).

NOTE: A wheel puller may be needed if sheave can not be removed by hand. Retain key (11).

3.Slide shaft assembly (12), lower bearing (5), and long spacer (10) out the bottom of spindle housing

(8).

4.Remove upper bearing (5) and spacer (4) from top of spindle housing.

5.Inspect parts and replace as needed.

1.3/8 NF x 1 HHCS

2.Cup washer

3.Sheave

4.Spacer

5.Spindle bearing

6.3/8 NC Lock nut

7.1/4 Grease fitting

8.Spindle housing

9.3/8 NC x 1-1/2

HHCS

10.Spacer

11.Square key

12.Shaft assembly

13.Blade

14.Cup washer

15.5/8 NF x 2 HHCS

Figure 8. Blade Spindle Assembly

Assemble Spindle

1.Slide lower bearing (5) over shaft assembly (12) with seal down.

2.Slide long spacer (10) on shaft assembly.

24 Dealer Service

MAN0765 (12/5/2008)

 

 

Image 24
Contents Turf Batwing Introduction To the DealerTable of Contents SpecificationsGeneral Information Safety Safety RulesTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulShield Missing Rotating Blades Thrown Objects 33347E Operation OperationAttaching Mower to Tractor Cutting Height Adjustment Attaching Hydraulic HosesInterference Check CV Driveline Turning LimitsTransport Starting and Stopping MowerOperating Operating Technique Operating TipsUneven Terrain Removing Mower from TractorCheck that all shields and guards are properly Owner Service Owner ServiceLubrication Information Description Frequency Belt Servicing Blade ServicingBlade Installation Chain ShieldingTroubleshooting CleaningAfter Each Use Periodically or Before Extended StorageBelt Conditions Dealer Service Dealer ServiceBlade Spindle Repair Seal Replacement Seal InstallationVertical Shaft Seal Replacement Horizontal Shaft Seal ReplacementRemove Gearbox from Mower Disassemble GearboxReassemble Gearbox Gearbox Assembly Install Gearbox Install Drive SheaveJoint Disassembly Universal Joint RepairJoint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Optional EquipmentHydraulic Latch Release Installation Chain Shielding InstallationMulch Kit Installation Mulch Kit InstallationDealer Check List Dealer Check ListsPRE-DELIVERY Check List DEALER’S Responsibility Delivery Check DEALER’S ResponsibilityDealer Check List Parts Index PartsMain Frame Assembly Main Frame Assembly Parts List Part QTY DescriptionDeck Assembly Deck Assembly Parts List Gearbox seeTrailer Assembly Gearbox Assembly Blade & Spindle Assembly Wing Driveline Assembly Rear Driveline Assembly REF Part QTY DescriptionCV Driveshaft Assembly HUB & Axle AssemblyCaster Wheel Assembly Hydraulic Cylinder Rear Chain Shielding Optional Hydraulic Release KIT OptionalMulch KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty