Woods Equipment RB850-4, RB750-4 manual Lubrication, Bolts, Cleaning, Blade Cutting Edge

Page 13

￿￿￿￿￿￿￿OWNER SERVICE

LUBRICATION

Weekly

„Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death.

„Make sure that all operating and service person- nel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gan- grene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. DO NOT DELAY.

„Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

„Never perform service or maintenance with engine running.

„Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

Oil the pivot pins with SAE 30 oil.

8 Hours

Grease optional skid shoes.

BOLTS

1.Check bolts periodically to be sure they are tight.

2.Replace bolts as needed.

NOTE: Replacement bolts must have the same strength markings on the heads. Refer to bolt torque on page 47.

CLEANING

After Each Use

●Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine.

●Inspect machine and replace worn or damaged parts.

●Replace any safety decals that are missing or not readable.

Periodically or Before Extended Storage

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

„Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head.

BLADE CUTTING EDGE

To reverse the cutting edge

1.Remove the 5/8" plow bolts.

2.Remove the cutting edge from the moldboard and reinstall with the sharp edge down.

3.Replace cutting edge when both edges are worn.

●Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine.

●Remove the remainder using a low-pressure water spray.

1.Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface.

2.Be careful when spraying near chipped or scratched paint as water spray can lift paint.

3.If a pressure washer is used, follow the advice of the pressure washer manufacturer.

●Inspect machine and replace worn or damaged parts.

●Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer).

●Replace any safety decals that are missing or not readable (supplied free by your Woods dealer). See Safety Decals section for location drawing.

MAN0160 (Rev. 2/22/2006)

Owner Service 13

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Rear Blades Introduction General Information Table of ContentsModel RB750-4 & RB850-4 SpecificationsPreparation Safety RulesTraining OperationTransportation MaintenanceStorage Replace Immediately If Damaged Safety & Instructional DecalsCrushing Pinching Hazard Be CarefulMount Blade to Tractor OperationReverse Blade Blade Angle AdjustmentOffset Swing Tilt AdjustmentLeveling and Grading BackfillingPRE-OPERATION Check List Lubrication CleaningBolts Blade Cutting EdgeAssembly Table of Contents AssemblyDealer SET-UP Instructions Attach Boom to Pivot Assembly Main Assembly All Models Attach Blade to Pivot AssemblyAttach A-Frame Install Manual TubeRefer to Figure Install Slow Moving Vehicle SignManual Configuration Models M & MT Install Offset LinkageAngle Kit Installation Tilt Kit Installation with Manual Angle Control Models MT & TA Install Hydraulic Tilt KitHydraulic Tilt and Angle Kit Hose Routing Model TA Install Hydraulic Tilt KitOffset Angle Offset Model H Install Hydraulic CylindersOffset Install Relief Valves and HosesSelector Valve Install Selector Valve Kit 1004873 OptionalHandle Kit Installed Route hoses as shown in Figure Install Selector Valve Kit Optional Cont’dOptional Equipment ALL Models Install Pneumatic Tailwheel 28775 OptionalSkid Shoe Installation Install Skid Shoe Kit 18296 OptionalPRE-DELIVERY Check List Install End Plate Kit 22658 OptionalDelivery Check List Assembly Parts Index Rear Blades RB750-4 RB850-4 Main Assembly Part QTY Description RB750-4 RB850-4 Main Assembly Parts ListRB750-4 RB850-4 Models M & MT RB750-4 RB850-4 Models MA, SA, & TA RB750-4 RB850-4 Model H RB750-4 RB850-4 Model H Parts List For Models MT & TA RB750-4 RB850-4 Hydraulic Tilt KITFor Model SA RB750-4 RB850-4 Hydraulic Offset KITHydraulic Angle KIT Selector Valve KIT Relief Valve Cartridge 1600 psi Selector Valve Relief ValveSeal Kit 3-1/2 Hyd Cylinder Hydraulic Cylinder Assembly & Parts ListPneumatic Tailwheel Assembly Wheel HUB, Tire & Wheel Assembly END Plate KIT Skid Shoe KITSAE Series Torque Chart Bolt Torque ChartMetric Series Abbreviations Bolt Size ChartWarranty Warranty

RB750-4, RB850-4 specifications

The Woods Equipment RB850-4 and RB750-4 are two powerful and efficient rotary tillers designed for serious lawn and garden care. Both models embody rugged construction and advanced technology, making them ideal choices for homeowners and professionals alike.

The RB850-4 offers an outstanding working width of 85 inches, enabling the user to cover a significant area in a shorter time frame. This model is equipped with four durable, cast iron gearboxes that facilitate smooth operation and prolong the lifespan of the equipment. The adjustable tilling depth allows operators to customize the soil preparation according to specific needs, whether for seedbed preparation or incorporating organic matter into the soil.

On the other hand, the RB750-4 features a slightly narrower working width of 75 inches, providing agility in tighter spaces without compromising performance. It also employs the same four cast iron gearboxes for reliable power distribution. The robust tines of both models are specifically designed for efficient soil mixing, turning and aeration, enhancing soil structure and health.

One of the main features of both the RB850-4 and RB750-4 is the innovative Quick-Connect attachment that streamlines the process of interchanging with other implements. This design principle enhances productivity, allowing users to quickly switch tools without wasting time. Moreover, both models are engineered for compatibility with a broad range of tractors, enhancing their adaptability across various farming and gardening applications.

The advanced technologies incorporated into these tillers also include a protective shield that reduces the risk of debris getting stuck in the tines. This not only extends the operational capability of the tillers but also enhances user safety during operation. Additionally, the rear roller on both models ensures a smooth finish, leveling the soil after tilling.

In summary, the Woods Equipment RB850-4 and RB750-4 rotary tillers combine power, efficiency, and versatility into a high-performance package. With their robust design, adjustable features, and advanced technologies, these tillers stand out in the market, promoting healthier soil and contributing to successful gardening and landscaping outcomes. Whether for intensive tilling or light garden maintenance, both models offer unparalleled value and reliability, making them a worthy investment for both amateur and professional users.
Top Page Image Contents