Woods Equipment RB850-4 Optional Equipment ALL Models, Install Pneumatic Tailwheel 28775 Optional

Page 27

OPTIONAL EQUIPMENT - ALL MODELS

Install Pneumatic Tailwheel 28775 (Optional)

IMPORTANT

When grading with tailwheel attached, do not attach upper link of tractor 3-point hitch to blade without using floating links (2 & 3). Without float- ing links, equipment damage may result and void warranty.

Refer to Figure 30.

The tailwheel is very helpful for finish grading and lev- eling work. The ratchet controls the approximate cut- ting height.

1.Remove top link of tractor 3-point hitch.

NOTE: Do not use with Category 2 quick-attach cou- plers.

3.Secure into position with top link pin.

4.Attach bracket (9) to boom assembly with clevis pin (10), two flat washers (12) and two cotter pins (13). Secure together with cap screw (14).

5.Attach tailwheel arm (15) and yoke (24) to bracket

(9) with clevis pin (11), washers (26), and cotter pin (13).

6.Attach ratchet (8) between bracket (9) and tail- wheel arm (15). Secure with pins supplied with ratchet.

2.Attach float links (2 & 3) and sleeve (4) to inside of the top holes of A-Frame. 3/4 dia. welded pin on side of float links must face outward and be located on the bottom end.

7.Attach top link to float links (2 & 3) using clevis pin (5), two SAE flat washers (6), and cotter pins (7).

1

 

 

 

14.

Cap Screw, 1/2 NC x

 

 

 

 

1-3/4 GR5

 

 

 

15.

Tailwheel Arm Asy

 

 

 

16.

Cap, Dust

2.

Link, Floating Right

17.

O-Ring .09 x 1.56 OD

18.

Bushing, Bronze 1.5

3.

Link,

Floating Left

 

x 1.63 x 1.50

 

4.

Sleeve,

1.00 x 1.25 x 1.44

19.

Grease Fitting,

1/4-28

5.

Pin, Clevis 1 x 4-29/32 HT

 

Tapered Thread

 

6.

Washer, Flat 1” SAE

20.

Grease Fitting,

1/8

7.

Pin, Cotter 1/4 x 2-1/4

 

Pipe Thread

 

8.

Ratchet

21.

Plate, Top Dampener

9.

Tailwheel Bracket Asy

22.

Disc, Friction 4 x 6.15

10.

Pin, Clevis 3/4 x 12-1/4

23.

Pin, Spirol

11.

Pin, Clevis 1 x 12-1/4

 

7/16 x 2-1/2

12.

Washer, Flat 3/4 Standard

24.

Wheel Yoke Asy

13.

Pin, Cotter 1/4 x 1-1/2

26.

Washer, Flat 1” Std

Figure 30. Pneumatic Tailwheel Installation

MAN0160 (Rev. 2/22/2006)

Assembly 27

 

 

 

Image 27
Contents Rear Blades Introduction General Information Table of ContentsModel RB750-4 & RB850-4 SpecificationsOperation Safety RulesPreparation TrainingMaintenance TransportationStorage Replace Immediately If Damaged Safety & Instructional DecalsCrushing Pinching Hazard Be CarefulMount Blade to Tractor OperationReverse Blade Blade Angle AdjustmentOffset Swing Tilt AdjustmentBackfilling Leveling and GradingPRE-OPERATION Check List Blade Cutting Edge CleaningLubrication BoltsAssembly Assembly Table of ContentsDealer SET-UP Instructions Attach Boom to Pivot Assembly Main Assembly All Models Attach Blade to Pivot AssemblyAttach A-Frame Install Manual TubeRefer to Figure Install Slow Moving Vehicle SignManual Configuration Models M & MT Install Offset LinkageAngle Kit Installation Tilt Kit Installation with Manual Angle Control Models MT & TA Install Hydraulic Tilt KitHydraulic Tilt and Angle Kit Hose Routing Model TA Install Hydraulic Tilt KitOffset Angle Offset Model H Install Hydraulic CylindersOffset Install Relief Valves and HosesSelector Valve Install Selector Valve Kit 1004873 OptionalHandle Kit Installed Route hoses as shown in Figure Install Selector Valve Kit Optional Cont’dOptional Equipment ALL Models Install Pneumatic Tailwheel 28775 OptionalSkid Shoe Installation Install Skid Shoe Kit 18296 OptionalInstall End Plate Kit 22658 Optional PRE-DELIVERY Check ListDelivery Check List Assembly Parts Index Rear Blades RB750-4 RB850-4 Main Assembly Part QTY Description RB750-4 RB850-4 Main Assembly Parts ListRB750-4 RB850-4 Models M & MT RB750-4 RB850-4 Models MA, SA, & TA RB750-4 RB850-4 Model H RB750-4 RB850-4 Model H Parts List For Models MT & TA RB750-4 RB850-4 Hydraulic Tilt KITFor Model SA RB750-4 RB850-4 Hydraulic Offset KITHydraulic Angle KIT Selector Valve KIT Relief Valve Cartridge 1600 psi Selector Valve Relief ValveSeal Kit 3-1/2 Hyd Cylinder Hydraulic Cylinder Assembly & Parts ListPneumatic Tailwheel Assembly Wheel HUB, Tire & Wheel Assembly END Plate KIT Skid Shoe KITBolt Torque Chart SAE Series Torque ChartMetric Series Abbreviations Bolt Size ChartWarranty Warranty

RB750-4, RB850-4 specifications

The Woods Equipment RB850-4 and RB750-4 are two powerful and efficient rotary tillers designed for serious lawn and garden care. Both models embody rugged construction and advanced technology, making them ideal choices for homeowners and professionals alike.

The RB850-4 offers an outstanding working width of 85 inches, enabling the user to cover a significant area in a shorter time frame. This model is equipped with four durable, cast iron gearboxes that facilitate smooth operation and prolong the lifespan of the equipment. The adjustable tilling depth allows operators to customize the soil preparation according to specific needs, whether for seedbed preparation or incorporating organic matter into the soil.

On the other hand, the RB750-4 features a slightly narrower working width of 75 inches, providing agility in tighter spaces without compromising performance. It also employs the same four cast iron gearboxes for reliable power distribution. The robust tines of both models are specifically designed for efficient soil mixing, turning and aeration, enhancing soil structure and health.

One of the main features of both the RB850-4 and RB750-4 is the innovative Quick-Connect attachment that streamlines the process of interchanging with other implements. This design principle enhances productivity, allowing users to quickly switch tools without wasting time. Moreover, both models are engineered for compatibility with a broad range of tractors, enhancing their adaptability across various farming and gardening applications.

The advanced technologies incorporated into these tillers also include a protective shield that reduces the risk of debris getting stuck in the tines. This not only extends the operational capability of the tillers but also enhances user safety during operation. Additionally, the rear roller on both models ensures a smooth finish, leveling the soil after tilling.

In summary, the Woods Equipment RB850-4 and RB750-4 rotary tillers combine power, efficiency, and versatility into a high-performance package. With their robust design, adjustable features, and advanced technologies, these tillers stand out in the market, promoting healthier soil and contributing to successful gardening and landscaping outcomes. Whether for intensive tilling or light garden maintenance, both models offer unparalleled value and reliability, making them a worthy investment for both amateur and professional users.