Woods Equipment RB850-4, RB750-4 manual Angle Kit Installation

Page 19

Models: MA, SA, & TA or Optional Hydraulic Angle Kit 1004870

Install Hydraulic Angle Cylinder

Refer to Figure 14.

1.	Remove lock pin assembly (2) and safety pin (10)
from rear of boom, if previously installed. See Figure
13 on page 18 for lock pin assembly location.
2.	Remove hardware and retaining cap (3) from top
of boom if previously installed. See Figure 13 on page

24

7

5

27 4

25

26

18 for retaining cap location.

8

23 22

3.	Place hydraulic angle arm assembly (4) on boom
as shown Figure 14.
4.	Secure into position using three cap screws (27),
lock washers (25), and flat washers (26).
5.	Attach hydraulic cylinder (6) to boom and hydrau-
lic angle arm assembly as shown. Secure with pins
supplied with the cylinder.
6.	Attach hose holder (5) to A-Frame using carriage
bolt (24), flat washer (23), and lock nut (22).
7.	Install adjustable elbows (7) and hoses (8) (Mod-
els MA and TA) to cylinder.

NOTE: Do not install 84” hoses (8) if Hydraulic Offset cylinder is to be installed.

8.Route hoses as shown in Figure 15.

4.Hyd Angle Arm Assembly

5.Hyd Hose Holder

6.Hyd Cylinder 3-1/2 x 16

7.Elbow, 3/4 ORBM 3/4 JICM 90

8Hose, 3/8 84 1/2 NPTM 3/4 JICF

9.Strap, Binding 14-1/2

22.Nut, Lock 3/8

23.Washer, Flat 3/8 Standard

24.Bolt, Carriage 3/8 NC x 1-1/4 GR1

25.Washer, Lock 3/4

26.Washer, Flat 3/4 SAE

27.Cap Screw, 3/4 NC x 3 GR5

8 7

9

6

CD5986

Figure 14. Angle Kit Installation

CD5998

Figure 15. Angle Kit Hose Routing

NOTE: For model SA, Proceed to page 22 for hydraulic offset cylinder and relief valve installa- tion instructions.

MAN0160 (Rev. 2/22/2006)	Assembly 19
MAN0160 (Rev. 2/22/2006)

Image 19

Contents Rear Blades Introduction General Information Table of ContentsModel RB750-4 & RB850-4 SpecificationsOperation Safety RulesPreparation TrainingTransportation MaintenanceStorage Replace Immediately If Damaged Safety & Instructional DecalsCrushing Pinching Hazard Be CarefulMount Blade to Tractor OperationReverse Blade Blade Angle AdjustmentOffset Swing Tilt AdjustmentLeveling and Grading BackfillingPRE-OPERATION Check List Blade Cutting Edge CleaningLubrication BoltsAssembly Table of Contents AssemblyDealer SET-UP Instructions Attach Boom to Pivot Assembly Main Assembly All Models Attach Blade to Pivot Assembly Attach A-Frame Install Manual TubeRefer to Figure Install Slow Moving Vehicle SignManual Configuration Models M & MT Install Offset LinkageAngle Kit Installation Tilt Kit Installation with Manual Angle Control Models MT & TA Install Hydraulic Tilt KitHydraulic Tilt and Angle Kit Hose Routing Model TA Install Hydraulic Tilt KitOffset Angle Offset Model H Install Hydraulic CylindersOffset Install Relief Valves and HosesSelector Valve Install Selector Valve Kit 1004873 OptionalHandle Kit Installed Route hoses as shown in Figure Install Selector Valve Kit Optional Cont’dOptional Equipment ALL Models Install Pneumatic Tailwheel 28775 OptionalSkid Shoe Installation Install Skid Shoe Kit 18296 OptionalPRE-DELIVERY Check List Install End Plate Kit 22658 OptionalDelivery Check List Assembly Parts Index Rear Blades RB750-4 RB850-4 Main Assembly Part QTY Description RB750-4 RB850-4 Main Assembly Parts ListRB750-4 RB850-4 Models M & MT RB750-4 RB850-4 Models MA, SA, & TA RB750-4 RB850-4 Model H RB750-4 RB850-4 Model H Parts List For Models MT & TA RB750-4 RB850-4 Hydraulic Tilt KITFor Model SA RB750-4 RB850-4 Hydraulic Offset KITHydraulic Angle KIT Selector Valve KIT Relief Valve Cartridge 1600 psi Selector Valve Relief ValveSeal Kit 3-1/2 Hyd Cylinder Hydraulic Cylinder Assembly & Parts ListPneumatic Tailwheel Assembly Wheel HUB, Tire & Wheel Assembly END Plate KIT Skid Shoe KITSAE Series Torque Chart Bolt Torque ChartMetric Series Abbreviations Bolt Size ChartWarranty Warranty