Woods Equipment MX54T, MX61T manual PRE-OPERATION Check List, Owners Responsibility

Page 15

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___

Review and follow all safety rules and safety

 

decal instructions on page 5 through page 8.

___

Check that all safety decals are installed and in

 

good condition. Replace if damaged.

___

Check to make sure all shields and guards are

 

properly installed and in good condition. Be sure

 

that either the discharge chute, mulching end

 

cap, or complete vacuum attachment is installed.

___

Check that all hardware and cotter pins are prop-

 

erly installed and secure.

___

Check to ensure blades are sharp, in good condi-

 

tion, and installed correctly. Replace if damaged.

___

Check that equipment is properly and securely

 

attached to power unit.

___

Do not allow riders.

___

Inspect area and remove stones, branches or

 

other hard objects that might be thrown, causing

 

injury or damage.

___ Check engine oil level. Clean area around oil fill dipstick. Remove dipstick and check to be sure oil is in operating range (between marks on dip- stick). Add oil if necessary but Do Not Overfill. Install Dipstick assembly firmly until cap bottoms out on tube. Dipstick assembly must always be secured into fill tube when engine is running.

___ Check all lubrication points and grease as instructed in Lubrication, page 16.

___ Perform a functional check of the safety interlock system each time you operate the unit. Place both steering levers outward, start engine, engage PTO and then rise up out of the seat. The engine should die when you raise up. If it does not, do not operate unit until the safety interlock system has been repaired and operates properly.

____ Check that the PowerTilt™ deck safety switch is

working properly. While sitting in the seat, with the engine running, raise the deck to a partially tilted position and move a traction arm out of neu- tral. The engine should shut off. Repeat the same steps with the deck in the cutting height range. The engine should continue to run with the trac- tion arms moved out of neutral.

™

MAN0253 (Rev. 3/10/2007)

Operation 15

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MAN0253 To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsPreparation SafetySafety Rules TrainingStorage MaintenanceMX54 & MX61 Safety & Instructional DecalsBe Careful Attaching Mower to Power Unit OperationOperation PowerTilt Operation & Figure Cutting Height AdjustmentTo tilt deck up Mower SIDE-TO-SIDE AdjustmentStorage Position Mowing TipsMowing Conditions TroubleshootingBelt Conditions Mowing ConditionsOwners Responsibility PRE-OPERATION Check ListService ServiceLubrication Blade Sharpening Blade ServiceBlade Installation Blade RemovalBelt Service Belt Adjustment FigureBelt Replacement Spindle Repair Figure Spindle Removal Spindle DisassemblySpindle Assembly Rear Pivot Lift ARM ServiceLift Linkage Bushing Replacement Caster Wheel MaintenanceReturning to Operation CleaningAfter Each Use Periodically or Before Extended StorageDealer SET-UP Instructions AssemblyAssembly Instructions Mower Assembly FigurePreparation All Models Install Discharge Chute FigureWiring Connection MXT Deck SN 1100886 & above Wiring Connections MXT Deck SN 1100886 and aboveFZ Series Power Units without timer delay Figure Deck Attachment All Models Adjust Mower Deck & FigureAdjust Cutting Height Apply Deck Height Decal PowerTilt UnitsAdjust Mower SIDE-TO-SIDE Anti-Scalp Height Adjustment Linkage PowerTilt Models Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts MOW’N Machine Mower DeckMX54 & MX61 Deck Assembly Part QTY Description MX54 & MX61 Deck Assembly Parts ListMX54T & MX61T Deck Assembly with Powertilt Parts Deck Drive System Deck Drive System Parts List Right Angle Gearbox Assembly Floating Deck Lift ARM Powertilt Assembly For MX54/MX61 Manually Controlled Cutting Height Height Adjustment Handle AssemblyWheel Lift Assembly Blade Spindle Assembly Mulch KIT Parts Powertilt with Timer Delay FZ Series Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexLimited Warranty Warranty Woods Equipment Company
Top Page Image Contents