Woods Equipment MX54T, MX61T manual Adjust Cutting Height, Apply Deck Height Decal PowerTilt Units

Page 27

MX61/MX61T

Right Lift Rod Assembly

23.00"

MX61/MX61T

Left Lift Rod Assembly

22.88"

MX61

Right Ground Rod Assembly 13.25"

MX54/MX51T

Right Lift Rod Assembly

22.12"

MX54/MX51T

Left Lift Rod Assembly

21.75"

MX54

Right Ground Rod Assembly 12.25"

 

 

Figure 27. Adjustment Rod Length

 

ADJUST CUTTING HEIGHT

1.With power unit and mower on a level surface and power unit tire pressure set equally on both sides, set cutting height on MX54/MX61 by moving the height adjustment handle forward to lower the cut- ting height and rearward to raise the cutting height. Use the PowerTilt switch on MX54T/MX61T mod- els.

2.In the high cut range, the caster wheel assembly should be bolted through the lower hole in the caster fork. Anti-scalp rollers should be installed in the lower mounting hole. Use the high cut range for the PowerTilt™ decks.

3.In the low cut range, the caster wheel assembly should be bolted through the upper hole in the caster fork. Anti-scalp rollers should be installed in the upper mounting hole.

4.When the caster wheels are moved to a different hole in the fork, it will be necessary to move the rear pivot lift arm to the corresponding hole in the power unit mounting brackets. See Figure 26, page 26.

5.If cut height does not correspond to the respective position for the height adjustment handle on MX54/MX61, the ground rod should be adjusted. See Adjust Mower Deck, page 26. For MX54T and MX61T, the cut height is aligned with the height decal.

Apply Deck Height Decal - PowerTilt Units

1.Turn power unit key to the ON position.

2.Activate rocker switch following decal instructions on top of rocker switch bracket and set blade cut- ting edge to 3 inches.

3.With mower deck level, place deck height decal (75423) on top of height gauge bracket to corre- spond to blade height. See Figure 28.

4.Check height indicator on the top of the actuator. Blade height and indicator should be at the same height.

Figure 28. Deck Height Indicator Decal Installed

ADJUST MOWER SIDE-TO-SIDE

Measure a similar spot to the ground on each rear corner of the mower deck. If there is more than an 1/8" difference between sides, adjust lift rods until sides are within 1/8".

(Rev. 6/8/2010)

MAN0253 (Rev. 3/10/2007)

Assembly 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents MAN0253 To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsPreparation SafetySafety Rules TrainingStorage MaintenanceMX54 & MX61 Safety & Instructional DecalsBe Careful Attaching Mower to Power Unit OperationOperation PowerTilt Operation & Figure Cutting Height AdjustmentTo tilt deck up Mower SIDE-TO-SIDE AdjustmentStorage Position Mowing TipsMowing Conditions TroubleshootingBelt Conditions Mowing ConditionsOwners Responsibility PRE-OPERATION Check ListService ServiceLubrication Blade Sharpening Blade ServiceBlade Installation Blade RemovalBelt Service Belt Adjustment FigureBelt Replacement Spindle Repair Figure Spindle Removal Spindle DisassemblySpindle Assembly Rear Pivot Lift ARM ServiceLift Linkage Bushing Replacement Caster Wheel MaintenanceReturning to Operation CleaningAfter Each Use Periodically or Before Extended StorageDealer SET-UP Instructions AssemblyAssembly Instructions Mower Assembly FigurePreparation All Models Install Discharge Chute FigureWiring Connection MXT Deck SN 1100886 & above Wiring Connections MXT Deck SN 1100886 and aboveFZ Series Power Units without timer delay Figure Deck Attachment All Models Adjust Mower Deck & FigureAdjust Cutting Height Apply Deck Height Decal PowerTilt UnitsAdjust Mower SIDE-TO-SIDE Anti-Scalp Height Adjustment Linkage PowerTilt Models Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts MOW’N Machine Mower DeckMX54 & MX61 Deck Assembly Part QTY Description MX54 & MX61 Deck Assembly Parts ListMX54T & MX61T Deck Assembly with Powertilt Parts Deck Drive System Deck Drive System Parts List Right Angle Gearbox Assembly Floating Deck Lift ARM Powertilt Assembly For MX54/MX61 Manually Controlled Cutting Height Height Adjustment Handle AssemblyWheel Lift Assembly Blade Spindle Assembly Mulch KIT Parts Powertilt with Timer Delay FZ Series Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexLimited Warranty Warranty Woods Equipment Company
Top Page Image Contents