Woods Equipment MX61T, MX54T manual Maintenance, Storage

Page 6

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

MAINTENANCE

„Before performing any service or maintenance, lower attachment to ground, turn off power unit engine, remove key, and disconnect battery ground cable (negative -).

„Block mower securely before working under- neath.

„Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

„Do not work under elevated mower deck unless lock-up mechanism is in good condition and fully engaged as instructed. Replace if damaged.

„Make sure attachment is properly secured, adjusted, and in good operating condition.

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

„Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened.

„Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

„Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

„Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

„Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

„Make sure shields and guards are properly installed and in good condition. Replace if dam- aged.

„Use care when installing or removing belt from spring-loaded idler. Springs store energy when extended and, if released suddenly, can cause per- sonal injury.

STORAGE

„Block equipment securely for storage.

„Follow manual instructions for storage.

„Keep children and bystanders away from stor- age area.

™

6Safety

MM DT/MX Mower Safety Rules (Rev. 3/10/2007)

Page 5 Page 7
Image 6
Page 5 Page 7
Contents MAN0253 Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationTraining SafetySafety Rules PreparationMaintenance StorageSafety & Instructional Decals MX54 & MX61Be Careful Attaching Mower to Power Unit OperationOperation Cutting Height Adjustment PowerTilt Operation & FigureMower SIDE-TO-SIDE Adjustment To tilt deck upMowing Tips Storage PositionTroubleshooting Mowing ConditionsMowing Conditions Belt ConditionsPRE-OPERATION Check List Owners ResponsibilityService ServiceLubrication Blade Removal Blade ServiceBlade Installation Blade SharpeningBelt Service Belt Adjustment FigureBelt Replacement Rear Pivot Lift ARM Service Spindle DisassemblySpindle Assembly Spindle Repair Figure Spindle RemovalCaster Wheel Maintenance Lift Linkage Bushing ReplacementPeriodically or Before Extended Storage CleaningAfter Each Use Returning to OperationMower Assembly Figure AssemblyAssembly Instructions Dealer SET-UP InstructionsInstall Discharge Chute Figure Preparation All ModelsWiring Connections MXT Deck SN 1100886 and above Wiring Connection MXT Deck SN 1100886 & aboveFZ Series Power Units without timer delay Figure Adjust Mower Deck & Figure Deck Attachment All ModelsAdjust Cutting Height Apply Deck Height Decal PowerTilt UnitsAdjust Mower SIDE-TO-SIDE Anti-Scalp Height Adjustment Linkage PowerTilt Models PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMOW’N Machine Mower Deck PartsMX54 & MX61 Deck Assembly MX54 & MX61 Deck Assembly Parts List Part QTY DescriptionMX54T & MX61T Deck Assembly with Powertilt Parts Deck Drive System Deck Drive System Parts List Right Angle Gearbox Assembly Floating Deck Lift ARM Powertilt Assembly Height Adjustment Handle Assembly For MX54/MX61 Manually Controlled Cutting HeightWheel Lift Assembly Blade Spindle Assembly Mulch KIT Parts Powertilt with Timer Delay FZ Series Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexLimited Warranty Warranty Woods Equipment Company
Top Page Image Contents