Woods Equipment MX61T, MX54T manual Assembly Instructions, Dealer SET-UP Instructions

Page 22

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this mower is the responsibility of the Woods dealer. It should be delivered to the owner com- pletely assembled, lubricated, and adjusted for normal cutting conditions.

The mower is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located on page 47.

DP1

Select a suitable working area. A smooth, hard, level

Figure 15. Left Front Corner Clip & Lag Bolt

surface, such as concrete, will make assembly much

 

quicker.

 

 

Remove front and rear hardware that secures deck to

 

crate as shown in Figure 15, Figure 16, and Figure 17.

 

Remove deck from crate.

 

Mower Assembly (Figure 18)

1.Remove lock nut (7), flat washer (4), and plastic washer (3) from both carriage bolts on the lift arm.

2.Remove cap screw (6), lock washer (5), and flat

washer (4) from the center hub on the rear pivot lift

DP2

 

arm (1).

 

Figure 16. Rear Clip & Lag Bolt

3. Attach rear pivot lift arm (1) to the center hub on

 

the lift arm and secure with cap screw (6), lock

 

 

washer (5), and flat washer (4). Torque to 85 lbs-ft.

 

4. Secure rear pivot lift arm (1) on both sides of center

 

hub with lock nuts (7), flat washers (4), and plastic

 

washers (3).

 

NOTE: Do not overtighten lock nuts (7). Rear pivot

 

lift arm must be tight but should pivot with effort.

 

5. On MX54 & MX61 models, remove clevis pin (9)

 

and safety pin (10) from lift handle. Rotate lift han-

DP3

dle up into the operating position and secure with

 

Figure 17. Rear Pivot Lift Arm Lag Bolts

clevis pin (9) and safety pin (10).

1.Rear pivot lift arm

2.5/8 NC x 2 Carriage bolt GR5

3..53 x 2.0 x .125 Plastic washer

4.5/8 ID x 2.0 OD x 3/8 Thick washer

5.1/2 Lock washer

6.1/2 NC x 1-1/2 HHCS GR5

7.5/8 NC Lock nut

9..62 x 1.50 Clevis pin

10. .19 x 3.16 Safety pin

Figure 18. Rear Pivot Lift Arm Assembly

22 Assembly

MAN0253 (Rev. 3/10/2007)

 

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents MAN0253 Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationTraining SafetySafety Rules PreparationMaintenance StorageSafety & Instructional Decals MX54 & MX61Be Careful Operation Attaching Mower to Power UnitOperation Cutting Height Adjustment PowerTilt Operation & FigureMower SIDE-TO-SIDE Adjustment To tilt deck upMowing Tips Storage PositionTroubleshooting Mowing ConditionsMowing Conditions Belt ConditionsPRE-OPERATION Check List Owners ResponsibilityService ServiceLubrication Blade Removal Blade ServiceBlade Installation Blade SharpeningBelt Adjustment Figure Belt ServiceBelt Replacement Rear Pivot Lift ARM Service Spindle DisassemblySpindle Assembly Spindle Repair Figure Spindle RemovalCaster Wheel Maintenance Lift Linkage Bushing ReplacementPeriodically or Before Extended Storage CleaningAfter Each Use Returning to OperationMower Assembly Figure AssemblyAssembly Instructions Dealer SET-UP InstructionsInstall Discharge Chute Figure Preparation All ModelsWiring Connections MXT Deck SN 1100886 and above Wiring Connection MXT Deck SN 1100886 & aboveFZ Series Power Units without timer delay Figure Adjust Mower Deck & Figure Deck Attachment All ModelsApply Deck Height Decal PowerTilt Units Adjust Cutting HeightAdjust Mower SIDE-TO-SIDE Anti-Scalp Height Adjustment Linkage PowerTilt Models PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMOW’N Machine Mower Deck PartsMX54 & MX61 Deck Assembly MX54 & MX61 Deck Assembly Parts List Part QTY DescriptionMX54T & MX61T Deck Assembly with Powertilt Parts Deck Drive System Deck Drive System Parts List Right Angle Gearbox Assembly Floating Deck Lift ARM Powertilt Assembly Height Adjustment Handle Assembly For MX54/MX61 Manually Controlled Cutting HeightWheel Lift Assembly Blade Spindle Assembly Mulch KIT Parts Powertilt with Timer Delay FZ Series Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexLimited Warranty Warranty Woods Equipment Company
Top Page Image Contents