Woods Equipment MX61T, MX54T manual Wiring Connections MXT Deck SN 1100886 and above

Page 24

Figure 20. Wiring Connection - MXT Deck (SN 1100886 & above)

Wiring Connections

MXT Deck SN 1100886 and above

1.Lift seat/hood and remove jumper (75521) from power unit’s main wire harness. (Located on front left side by steering pivot.) Keep jumper; power unit will not operate unless jumper or deck is attached.

2.Connect free end of deck safety harness to power unit’s main wire harness where jumper was previ- ously attached. Route harness through steering pivot slot (weatherpack connector).

3.Connect free end of deck actuator harness to power unit’s main wire harness. Route harness through steering pivot slot. The main wire harness connector is located underneath seat/hood by front left steering pivot. (Packard 56 series connector.)

4.Tie strap harnesses to front of power unit frame. Make sure wires are not pinched by steering link-

age during operation. Wire must also remain clear of tire and not pull tight during tilt operation or deck tilting side to side.

Connect Wiring Harness - PowerTilt™ Units MXT Deck SN 1100885 and below

NOTE: If you plan to use the MXT deck with the actua- tor switch mounted on the deck, you must determine which wire harness to use. Select harness 75407 for FZ power units. Select harness 75433 for F-series power units. These harnesses are provided with MXT decks having SN 1100885 and below.

1.Attach red and black wires from the power tilt cable (75407 or 75433) to the center terminals of the rocker switch as shown in Figure 21.

2.Insert opposite end of power tilt cable through left steering handle slot as shown in Figure 22.

24Assembly

(Rev. 1/11/2008)

MAN0253 (Rev. 3/10/2007)

Image 24

Contents MAN0253 Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationSafety Safety RulesTraining PreparationMaintenance StorageSafety & Instructional Decals MX54 & MX61Be Careful Attaching Mower to Power Unit OperationOperation Cutting Height Adjustment PowerTilt Operation & FigureMower SIDE-TO-SIDE Adjustment To tilt deck upMowing Tips Storage PositionTroubleshooting Mowing ConditionsMowing Conditions Belt ConditionsPRE-OPERATION Check List Owners ResponsibilityService ServiceLubrication Blade Service Blade InstallationBlade Removal Blade SharpeningBelt Service Belt Adjustment FigureBelt Replacement Spindle Disassembly Spindle AssemblyRear Pivot Lift ARM Service Spindle Repair Figure Spindle RemovalCaster Wheel Maintenance Lift Linkage Bushing ReplacementCleaning After Each UsePeriodically or Before Extended Storage Returning to OperationAssembly Assembly InstructionsMower Assembly Figure Dealer SET-UP InstructionsInstall Discharge Chute Figure Preparation All ModelsWiring Connections MXT Deck SN 1100886 and above Wiring Connection MXT Deck SN 1100886 & aboveFZ Series Power Units without timer delay Figure Adjust Mower Deck & Figure Deck Attachment All ModelsAdjust Cutting Height Apply Deck Height Decal PowerTilt UnitsAdjust Mower SIDE-TO-SIDE Anti-Scalp Height Adjustment Linkage PowerTilt Models Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMOW’N Machine Mower Deck PartsMX54 & MX61 Deck Assembly MX54 & MX61 Deck Assembly Parts List Part QTY DescriptionMX54T & MX61T Deck Assembly with Powertilt Parts Deck Drive System Deck Drive System Parts List Right Angle Gearbox Assembly Floating Deck Lift ARM Powertilt Assembly Height Adjustment Handle Assembly For MX54/MX61 Manually Controlled Cutting HeightWheel Lift Assembly Blade Spindle Assembly Mulch KIT Parts Powertilt with Timer Delay FZ Series Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexLimited Warranty Warranty Woods Equipment Company