Woods Equipment FZ25D manual Dealer Service, Troubleshooting Hydrostatic Pump

Page 21

DEALER SERVICE

The information in this section is written for dealer ser- vice personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in this type of repair, you may be time and money ahead to replace complete assemblies.

„Before performing any service or maintenance, lower attachment to ground, turn off power unit engine, remove key, and disconnect battery ground cable (negative -).

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

TROUBLESHOOTING HYDROSTATIC PUMP

Loss of Power in Transmission

1.Make sure transmission fluid is correct.

2.Make sure hydrostatic pump and fan blades are clean.

NOTE: Overheating can cause loss of power or fluid leaks from excess fluid expansion.

3.Make sure dump valves are tightened down.

NOTE: Transmission fluid can leak by the dump valve if by-pass is not tight. Tighten hex head if dump valves are loose.

No Positive Neutral Position

If drive wheels travel forward or reverse when steering handles are in the NEUTRAL position (pivoted out- ward), adjustment of hydrostatic pumps is necessary.

1.Block up power unit frame so both drive wheels are off the ground.

2.Release parking brake.

3.Loosen jam nut (1) on linkage rod as shown in Figure 10.

4. Place steering handles in the NEUTRAL position (pivoted outward) and start engine.

5. If drive wheels turn, turn rod out or in until wheel stops.

6. Tighten jam nut.

7. Repeat steps 3 through 6 for other hydrostatic pump control arm.

1

Figure 10. Jam Nut on Linkage Rod, Left Pump

Straight Line Travel Adjustment

1.Check tire pressure; tires must have equal air pressure.

2.Check travel; drive forward with both steering handles full forward at half throttle.

If travel is not straight, adjust steering handle stop bolt on opposite side of turn.

If power unit turns to the left, raise steering stop bolt on the right.

If power unit turns to the right, raise steering stop bolt on the left.

DP4

Figure 11. Left Side Steering Stop Bolts

MAN0646 (Rev. 11/5/2007)

Dealer Service 21

 

 

Image 21
Contents MOW’N Machine To the Dealer IntroductionTable of Contents General Information SpecificationsSafety Rules SafetyTraining PreparationOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsBe Careful Operation OperationDeck HEIGHT/POWER Tilt Adjustment Switch Controls and SwitchesBrake & Temperature Lights Safety Switch SystemCold Weather Starting Tips Starting EngineStarting Mower or Attachment Stopping Mower or AttachmentSteering Handle Positions Steering Handle OperationMoving Disabled Power Unit Weight TransferStopping Engine Manual Fuel Shut-Off ValveOwners Responsibility Owner PRE-OPERATION Check ListOwner Service Owner ServiceEngine Service Radiator and PrescreenTailwheel Maintenance Lubrication Service IntervalsHydrostatic Transmission Service Battery ServiceHydraulic Transmission Change OIL & Filter Clutch Burnishing CleaningReturn to Operation After Each UseDealer Service Dealer ServiceTroubleshooting Hydrostatic Pump Engine Dies when Steering Handles are Engaged Troubleshooting EngineTroubleshooting Deck Safety Switch Hydrostatic Pump InstallationHydrostatic Pump & Belt Removal PTO Belt Removal Parking Brake AdjustmentEngine Removal Solenoid TestInstall Clutch Align BeltReassemble Components Clutch & Drive Components Reassembled Assembly AssemblyInstall Drive Tires Adjust Steering HandlesStraight Line Travel Install Single Tailwheel OptionalDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0646 Rev /5/2007 Parts FZ25DFZ25D Frame Assembly Part QTY Description FZ25D Frame Assembly Parts ListFZ25D Engine Assembly REF Part QTY Description FZ25D Engine Assembly Parts ListHydraulic Reservoir & Hoses Hydraulic Diagram Hydraulic Reservoir & Hoses Parts ListPTO, Clutch & Pump Assembly PTO Clutch & Pump Assembly Parts List Seat & Hood Assembly Single Tailwheel Assembly Wide Stance Tailwheel Assembly Tailwheel AssemblyBrake Assembly Tire & Wheel Chart Brake Assembly Parts ListFZ25D Wiring Diagram Kubota FZ25D Wiring Diagram Kubota Diesel Steering Assembly Counterweight Mount KIT Headlight KIT Optional SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexLimited Warranty Mow’n MachineTM Zero-Turn Mower Replacement Parts Woods Equipment Company

FZ25D specifications

The Woods Equipment FZ25D is a versatile and powerful piece of machinery designed for professional landscapers and grounds maintenance operations. This compact yet robust zero-turn mower boasts a range of features that make it ideal for tackling various mowing tasks efficiently and effectively.

One of the standout features of the FZ25D is its powerful engine. Equipped with a reliable engine, it ensures excellent performance and reliability during operation. With a horsepower rating that enhances its cutting power, the FZ25D can easily handle tough grass and uneven terrains, providing a smooth and immaculate finish to manicured lawns.

The zero-turn capability of the FZ25D is another significant advantage, allowing for unparalleled maneuverability. It features a dual-hydrostatic transmission that offers quick and responsive turns, enabling operators to navigate around obstacles, flower beds, and tight corners with ease. This capability reduces mowing time and increases productivity, making it a preferred choice for professionals.

The mower deck of the Woods Equipment FZ25D is designed for optimal cutting performance, featuring a durable construction that withstands rigorous use. Its cutting width allows for a large mowing area covered in a single pass, ensuring efficiency in operation. Additionally, the cutting height can be easily adjusted to suit various grass types and conditions, providing flexibility for different mowing scenarios.

Comfort is paramount in the design of the FZ25D. The operator station is ergonomically designed, offering a comfortable seating position with excellent visibility. The controls are intuitively placed, making it easy for operators to manage their mowing tasks without unnecessary strain. Furthermore, the mower is designed with vibration dampening technology to reduce operator fatigue, allowing for extended periods of use.

Maintenance is straightforward with the Woods Equipment FZ25D due to its easily accessible components. Users can quickly perform routine checks and necessary servicing, ensuring the mower remains in optimal working condition.

In summary, the Woods Equipment FZ25D combines power, maneuverability, and comfort, making it an excellent choice for landscaping professionals. Its advanced features, including a robust engine, zero-turn capability, durable cutting deck, and ergonomic design, cater to the demands of both commercial and residential mowing tasks, providing unmatched efficiency and performance.