Woods Equipment FZ25D manual Troubleshooting Deck Safety Switch, Hydrostatic Pump & Belt Removal

Page 23

engine. Push radiator forward until belt clears radiator cowl and engine sheave.

Figure 12. Power Tilt Deck Safety Switch Layout

Troubleshooting Deck Safety Switch

1.Pull handlebars in with deck in lowest cutting height position (1).

2.Check that switch is making contact with the height gauge.

3.Check that wires are properly hooked up to power unit.

4.Adjust switch bracket location on actuator if needed (four screws). Make sure height screw does not bottom out on slot in either direction when raising or lowering deck.

5.Check that screws holding switch to bracket are not too tight and holding lever open.

6.Adjust safety switch lever or replace switch if necessary,

7.After adjustments, check that engine cuts out with deck partially raised.

HYDROSTATIC PUMP & BELT REMOVAL

NOTE: Removal procedures are the same for both right and left hydrostatic pumps.

1.Place power unit on a level surface and remove key.

2.Place power unit on stands to allow access to bottom of the machine.

3.Drain hydraulic reservoir and hydrostatic pumps.

4.Remove steering linkage from control arm on hydrostatic pump.

5.Loosen J-bolt and remove belt.

6.If clearance between radiator cowl and engine sheave is too tight, loosen or remove rubber isolator (84) radiator mount located above the

Figure 13. Rubber Isolator & Radiator Mount

7.Remove hoses from hydrostatic pump. Plug and cap all fittings on hoses and pump to prevent contamination.

8.Remove H-drive that mounts sheave to hydrostatic pump. Use new 1/4 x 3/4 GR5 bolts in holes located 90° from previously occupied holes to separate H-drive from sheave.

9.Remove two bolts holding hydrostatic pump to frame and remove pump from frame. Hydrostatic pump weighs approximately 8 lbs; use care when removing.

HYDROSTATIC PUMP INSTALLATION

1.Position hydrostatic pump into power unit frame and secure with two bolts. Apply Loctite® 242 to threads of the two mounting bolts and torque to 35 lbs-ft.

2.Install sheave onto hydrostatic pump and secure H-drive. Alternate tightening each cap screw to 8 lbs-ft. Align sheave with spring idler to allow for proper belt alignment.

3.Install hoses to hydrostatic pump.

4.Install belts and tighten J-bolt for proper belt tension.

5.Install steering linkage to control arm on hydrostatic pump.

6.Fill hydraulic reservoir with new fluid. Use 20W-50 motor oil.

MAN0646 (Rev. 11/5/2007)

Dealer Service 23

 

 

Image 23
Contents MOW’N Machine To the Dealer IntroductionTable of Contents General Information SpecificationsPreparation SafetySafety Rules TrainingOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsBe Careful Operation OperationSafety Switch System Controls and SwitchesDeck HEIGHT/POWER Tilt Adjustment Switch Brake & Temperature LightsStopping Mower or Attachment Starting EngineCold Weather Starting Tips Starting Mower or AttachmentSteering Handle Positions Steering Handle OperationManual Fuel Shut-Off Valve Weight TransferMoving Disabled Power Unit Stopping EngineOwners Responsibility Owner PRE-OPERATION Check ListRadiator and Prescreen Owner ServiceOwner Service Engine ServiceTailwheel Maintenance Lubrication Service IntervalsHydraulic Transmission Change OIL & Filter Hydrostatic Transmission ServiceBattery Service After Each Use CleaningClutch Burnishing Return to OperationTroubleshooting Hydrostatic Pump Dealer ServiceDealer Service Engine Dies when Steering Handles are Engaged Troubleshooting EngineHydrostatic Pump & Belt Removal Troubleshooting Deck Safety SwitchHydrostatic Pump Installation Solenoid Test Parking Brake AdjustmentPTO Belt Removal Engine RemovalReassemble Components Install ClutchAlign Belt Clutch & Drive Components Reassembled Adjust Steering Handles AssemblyAssembly Install Drive TiresStraight Line Travel Install Single Tailwheel OptionalDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0646 Rev /5/2007 Parts FZ25DFZ25D Frame Assembly Part QTY Description FZ25D Frame Assembly Parts ListFZ25D Engine Assembly REF Part QTY Description FZ25D Engine Assembly Parts ListHydraulic Reservoir & Hoses Hydraulic Diagram Hydraulic Reservoir & Hoses Parts ListPTO, Clutch & Pump Assembly PTO Clutch & Pump Assembly Parts List Seat & Hood Assembly Single Tailwheel Assembly Wide Stance Tailwheel Assembly Tailwheel AssemblyBrake Assembly Tire & Wheel Chart Brake Assembly Parts ListFZ25D Wiring Diagram Kubota FZ25D Wiring Diagram Kubota Diesel Steering Assembly Counterweight Mount KIT Headlight KIT Optional Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexLimited Warranty Mow’n MachineTM Zero-Turn Mower Replacement Parts Woods Equipment Company

FZ25D specifications

The Woods Equipment FZ25D is a versatile and powerful piece of machinery designed for professional landscapers and grounds maintenance operations. This compact yet robust zero-turn mower boasts a range of features that make it ideal for tackling various mowing tasks efficiently and effectively.

One of the standout features of the FZ25D is its powerful engine. Equipped with a reliable engine, it ensures excellent performance and reliability during operation. With a horsepower rating that enhances its cutting power, the FZ25D can easily handle tough grass and uneven terrains, providing a smooth and immaculate finish to manicured lawns.

The zero-turn capability of the FZ25D is another significant advantage, allowing for unparalleled maneuverability. It features a dual-hydrostatic transmission that offers quick and responsive turns, enabling operators to navigate around obstacles, flower beds, and tight corners with ease. This capability reduces mowing time and increases productivity, making it a preferred choice for professionals.

The mower deck of the Woods Equipment FZ25D is designed for optimal cutting performance, featuring a durable construction that withstands rigorous use. Its cutting width allows for a large mowing area covered in a single pass, ensuring efficiency in operation. Additionally, the cutting height can be easily adjusted to suit various grass types and conditions, providing flexibility for different mowing scenarios.

Comfort is paramount in the design of the FZ25D. The operator station is ergonomically designed, offering a comfortable seating position with excellent visibility. The controls are intuitively placed, making it easy for operators to manage their mowing tasks without unnecessary strain. Furthermore, the mower is designed with vibration dampening technology to reduce operator fatigue, allowing for extended periods of use.

Maintenance is straightforward with the Woods Equipment FZ25D due to its easily accessible components. Users can quickly perform routine checks and necessary servicing, ensuring the mower remains in optimal working condition.

In summary, the Woods Equipment FZ25D combines power, maneuverability, and comfort, making it an excellent choice for landscaping professionals. Its advanced features, including a robust engine, zero-turn capability, durable cutting deck, and ergonomic design, cater to the demands of both commercial and residential mowing tasks, providing unmatched efficiency and performance.