Yazoo/Kees ZEKW42170, ZEKW52210 manual Battery, Maintenance

Page 39
Battery

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Recharge at 6-10 amperes for 1 hour

To clean battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Open the terminal access doors.

2.Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until shiny.

5.Coat terminals with grease or petroleum jelly

6.Reinstall battery.

Replacing battery

1.Lift Seat and rotate forward.

2.Open terminal access doors.

3.Using two 1/2" wrenches disconnect BLACK battery cable then RED battery cable.

4.Using 7/16" wrench, remove terminal guard.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall terminal guard.

8.First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

Always use protective glasses when handling the battery.

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

CZ-22

1.Terminal guard

2.Terminal access doors

Battery installation

English-37

Image 39
Contents 968999296/ZEKW52210 Operator’s manualModels 968999295/ZEKW42170Page Contents OPERATOR’S MANUALZE RIDER English-2 General INTRODUCTIONIntroduction CongratulationsManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSRead SAFETY INSTRUCTIONS Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance Use protective goggles IMPORTANT INFORMATION TransportCustomer responsibilities CONTROLS ControlsControl Locations 2. Motion Control Levers 1. Parking Brake1. Forward 4. Seat adjustment boltsTracking 3. Fuel Shut Off Valve5. Refueling 7. Fuses 6. By pass linkage10. Ignition Switch 8. Hour Meter9. Choke Control 11. Throttle Control 12. Blade switch13. Cutting height pedal AccessoriesOPERATION OperationTraining Starting the Engine Before Starting6.Move the throttle to the middle position 8.Open the fuel shut off valve IMPORTANT INFORMATION To start an engine with a weak battery Running Operating on hills Mowing patterns Mowing TipsStopping the Engine the parking brake is on Moving by Handthe engine stopped the ignition key has been removedMAINTENANCE MaintenanceMaintenance Schedule The engine is stopped The ignition key has been removedThe parking brake is on Battery Ignition System Checking the Safety System 2. Throttle cable Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Checking the Engines Cooling Air IntakeStandard air filter Replacing the Air Filter Kawasaki EngineReplacing the Fuel Filter Checking the Fuel Pump’s Air FilterChecking Tire Pressures Faulty adjustment can cause an accident Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation IZT belt Checking the Blades Blade replacement Adjusting the Mower Deck To adjust anti-scalprollers Use protective glasses when cleaning and washing Cleaning and WashingCaster Wheels HardwareMower is tracking to the right Tracking adjustmentParking brake To adjust parking brakeZE LUBRICATIONLubrication Lubrication Schedule3. Deck spindle Lubricating the Cables1. Front Wheel Mount 2. Front Wheel Bearings4. Deck outer spindle Checking the Oil Level Transaxle Transmission Fluid Change 6. Changing the Engine Oil Filter14.Proceed to the purge procedure Purging Procedures Trouble Shooting Guide TROUBLE SHOOTING GUIDEWater in the fuel Uneven mowing results Winter Storage ServiceSTORAGE StorageWIRING DIAGRAMS Wiring diagram1 13 11 5 12 Technical Data TECHNICAL DATAOverall dimensions EquipmentProductivity Torque Specifications CONFORMITY CERTIFICATES Conformity CertificatesUSA requirements SERVICE JOURNAL Service JournalDelivery Service After the First 5-8Hours 1. Change engine oilEnglish-69 6.Check/clean the engine’s cooling air intake 25-HourService4.Check battery with cables 5.Lubricate according to lubrication chart5.Check/adjust the parking brake 50-HourService1.Perform the 25-hourservice 4.Lubricate according to lubrication chart3.Change the engine oil filter 100-HourService2.Perform the 50-hourservice 4.Clean/replace the spark plugs300-HourService At Least Once Each Year English-75 English-76 English-77