Stow manual Stow G-4.5R Installation, Outdoor Installation, Mounting, Indoor Installation

Page 23

Outdoor Installation

Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

CAUTION

Pay close attention to ventilation when operating the generator inside tunnels and caves. The engine exhaust contains noxious elements.

Mounting

The generator should always be mounted on a flat level surface to isolate vibration of the generator when it is running. DO NOT place the generator on slopes, the possibility exists that the generator could slide.

STOW G-4.5R — INSTALLATION

Indoor Installation

Exhaust gases from gasoline engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

Eliminate the danger of deadly carbon monoxide gas. Remember that exhaust fumes from any gasoline engine are very poisonous if discharged in a closed room, but harmless if allowed to mix with the outside air.If the generator is installed indoors, you must make provisions for venting the engine exhaust to the outside of the building.

Generator Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground. Always use the ground terminal on the generator to ground the generator.

Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generator to earth ground.

a.Copper - 10 AWG (5.3 mm2) or larger.

b.Aluminum - 8 AWG (8.4 mm2) or larger.

2.When grounding the generator (Figure 3) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

STOW G-4.5R A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #3 (03/13/06) — PAGE 23

Image 23
Contents Model G-4.5R Page Heres HOW to GET Help Table of Contents When ordering parts Please supply the following information Parts Ordering ProceduresDimensions Stow G-4.5R DimensionsEffects of Altitude and Heat SpecificationsRespiratory Hazards Stow G-4.5R Safety Message Alert SymbolsBurn Hazards Rotating Parts Hazards Equipment DamageRead this manual Stow G-4.5R Rules for Safe OperationStow G-4.5R Rules for Safe Operation Power Cord SafetyEmergencies DeathPage Machine Safety Decals Operation and Safety Decals S/N 5498030 and belowOperation and Safety Decals S/N 5498031 and Above Engine Stow G-4.5R FamilarizationControl Panel Excitation SystemSmall Motors Single Phase LoadStow G-4.5R Load Application Incandescent LoadsGenerator Controls and Components Stow G-4.5R Controls and IndicatorsStow G-4.5R Controls and Indicators Stow G-4.5R Controls and Indicators With S/N 5498031 and above Generator Refueling Stow G-4.5R Generator RefuelingMounting Stow G-4.5R InstallationOutdoor Installation Indoor InstallationConnecting the Ground Stow G-4.5R InstallationMain Circuit Breaker General Inspection Prior to Operation Ground Power ToolsExtension Cable Fuel Check Stow G-4.5R PRE-INSPECTION EngineBefore Starting Engine Oil CheckBefore Starting the Engine Stow G-4.5R Initial START-UP EngineNoises that would associate with lose components Stow G-4.5R Initial START-UP ENGINE/OPERATION120 VAC Receptacles Main Circuit Breaker on Stopping The EngineGenerator Storage Stow G-4.5R Preparation for Long -TERM StoragePage Engine Maintenance Schedule Stow G-4.5R Maintenance EngineMaintenance Stow G-4.5R Maintenance EngineCleaning the Fuel Strainer Generator/Engine Wiring Diagram S/N 5498030 and Below Stow G-4.5R Wiring Diagram S/N 5498030 and belowStow G-4.5R Wiring Diagram S/N 5498031 and Above Stow G-4.5R -TROUBLESHOOTING Engine White Stow G-4.5R -TROUBLESHOOTING EngineGenerator Troubleshooting Stow G-4.5R -TROUBLESHOOTING GeneratorPage Items Found In the Items Number Column How to read the marks and remarks used in this parts bookTo 3 Units Stow G-4.5R Suggested Spare PartsNameplate and Decals S/N 5498030 and below Stow G-4.5R Name Plate and Decals S/N 5498030 and belowStow G-4.5R Name Plate and Decals S/N 5498030 and below Nameplate and Decals S/N 5498031 and Above Stow G-4.5R Name Plate and Decals S/N 5498030 and AboveDecal Operating Instructions Decal StowDecalwarning Read Manual Generator Assy Stow G-4.5R Generator AssySpring Washer Field Coil AssySET BOLT, Rotor SET WASHER, BearingControl BOX ASSY. S/N 549830 and below Stow G-4.5R Control BOX ASSY. S/N 549830 and belowStow G-4.5R Control BOX ASSY. S/N 549830 and below Control BOX ASSY. S/N 549831 and Above Stow G-4.5R Control BOX ASSY. S/N 549831 and AboveVR1H102MHA Stow G-4.5R Control BOX ASSY. S/N 549831 and AboveHEX NUT Pipe Frame ASSY. S/N 549830 and below Stow G-4.5R Pipe Frame ASSY. S/N 549830 and belowRubber Suspension Pipe FrameSUPPORT, Pipe Frame Engine BasePipe Frame ASSY. S/N 549830 and Above Stow G-4.5R Pipe Frame ASSY. S/N 549831 and AboveWASHER, Flat HangerPlastic Washer HEX Head BoltCrankcase Assy Robin EX270D20110- Crankcase AssyBall Bearing Valve GuideStem Seal OIL SealCrankshaft and Piston Assy Robin EX270D20110 Crankshaft and Piston AssyWoodruff KEY Connecting ROD BoltCrankshaft CP Flange NUTGovernor Assy Robin EX270D20110 Governor AssyGovernor Shaft SPRING, AdjustGovernor Operation Assy Governor LeverIntake and Exhaust Assy Robin EX270D20110 Intake and Exhaust AssyRelease Lever Adjust SCREW, M5X0.5X23LPIN, CAMSHAFT, 9DX78.5L Spring PIN, 4DX7.5DX11LAIR Cleaner Assy Robin EX270D20110 AIR Cleaner AssyElement Assy Body CPCOVER, LOW Profile Cooling Starting Assy Robin EX270D20110 Cooling Starting AssyBaffle 2, Head Blower Housing CP, YellowLABEL, Trademark 64D Baffle 1, Case CPFuel Lubricant Assy Robin EX270D20110 Carburetor AssyJET Slow Screw AdjustingValve Throttle Valve ChokeFlywheel Assy Robin EX270D20110 Flywheel AssyIgnition Coil CP Wire 2 CP, W/OIL SensorSwitch Assy Flywheel CPElectric Device Assy Robin EX270D20110 Electric Device AssyClamp CP OIL Sensor CPFLOAT, C/U CP3 Tapping BoltTerms and Conditions of Sale Stow Construction Equipment Page Heres HOW to GET Help

G-4.5R specifications

The Stow G-4.5R is an exceptional piece of rugged engineering designed for professionals who require efficiency and reliability in demanding environments. This cutting-edge equipment stands out for its unique combination of robust features and innovative technologies.

At the heart of the G-4.5R is its powerful engine, designed to facilitate high-performance operations. The machine is equipped with a fuel-efficient powertrain that not only maximizes output but also minimizes consumption. This feature is crucial for users who need to operate over extended periods without frequent refueling, making the G-4.5R highly suitable for long-term projects.

The G-4.5R boasts an advanced hydraulic system that enhances its lifting capabilities. With optimized hydraulic mechanics, the machine can handle heavier loads with improved precision and speed. This ensures that users can perform tasks more efficiently, reducing downtime and increasing productivity. Furthermore, the hydraulic system is complemented by a robust frame, designed to withstand rigorous field conditions while providing stability during operation.

Another notable aspect of the Stow G-4.5R is its user-centric design. The operational interface is intuitively laid out, allowing users to easily navigate controls and features without extensive training. The ergonomic design of the operating cabin further enhances comfort, reducing fatigue during long working hours. Noise reduction technologies have also been integrated into the design, making the working environment more pleasant.

In terms of technology, the G-4.5R features real-time monitoring systems that provide crucial operational data. These systems allow users to track fuel levels, hydraulic pressures, and performance metrics at a glance. Such capabilities not only promote efficient resource management but also facilitate preventive maintenance, helping to prolong the machine’s lifespan.

Safety is paramount in the design of the G-4.5R, with multiple safety mechanisms in place. These include automatic shutdown features in case of system overloads, reinforced caging to protect operators, and enhanced visibility systems that ensure a clear line of sight during operation.

In summary, the Stow G-4.5R is a versatile, powerful, and user-friendly machine specifically designed for challenging work environments. With its combination of advanced technologies, ergonomic design, and safety features, the G-4.5R stands out as a top choice for professionals aiming for efficiency and reliability in their operations.