Mustang M/8M, M2508/D, M100/SD, M250/S, M1008 manual Power Amplifier Module, Loudspeaker Output

Page 14

MACRO range installation manual. Issue 6

Fig. 7 Interconnection of several amplifiers

POWER AMPLIFIER MODULE

The power output stage of the amplifier including all low level drive circuitry, and output devices are contained in a module which is bolted to the rear panel by four screws. The module is connected into circuit by push-on tab connectors facilitating easy change of a suspect module. The module may be unbolted and swung out to enable circuitry to be worked on with power connected, though as the heatsink is no longer coupled, the module should not be driven into a load for any length of time. Output devices are mounted on sockets so they may be replaced without dismantling the PCB from the heatsink plate. See Fig. 8

Adjustments There are three pre-settable adjustments on the power output module which are accessible from the top of the amplifier. When received from the factory, the amplifier will have been adjusted for correct overload protection, output device biasing, and input sensitivity, and no further adjustment will be necessary. The recommended adjustments are:

OVERLOAD: Top left of module when viewed from front: Set for triggering at full amplitude on a load of 3 x rated output.

OUTPUT DEVICE BIASING: Centre top of module: Set nominally for a total module drain of 200mA, measured via the supply push-on tab.

INPUT SENSITIVITY: Top right of module: Set for 0.775V RMS at 1kHz.

The above adjustments necessitate the use of certain test equipment and facilities, and the precise methods are outside the scope of this manual. The adjustments may be identified by referring to Fig. 8

The front panel ëerrorí LED is energised for a minimum period of 1.5 sec. when an output overload condition is detected. During this time, the signal drive to the output stage is suppressed.

The detection circuit and LED will remain energised for the entire duration of any such overload, and the amplifier will return to normal operation 1.5 second after removal of the overload. Note therefore that this circuit will not register an overload until a suitable signal is present.

LOUDSPEAKER OUTPUT

The amplifier is designed to work primarily with 100V line loudspeaker systems. Facilities are also provided for 50V line and low impedance loads. IT IS ESSENTIAL to provide the correct loudspeaker load for safe and distortion-free reproduction.

When connecting a MACRO mixer amplifier or slave amplifier onto an existing loudspeaker network, the load should be ascertained by measuring the load by a proprietary impedance bridge

The cover provided on the output barrier terminals is a safety cover and should be retained. Access to the terminals is gained by Page 14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Mustang Macro range installation manual. Issue Index Appendix a Appendix B Appendix C Appendix D Appendix E Introduction Tone Control & Master Gain Adjustment General Specifications Mixer AmplifiersFront Panel Controls & Indicators Slave AmplifiersInput Module System NON-PRIORITY Modules General Specifications Microphone Input ModulesMicrophone & Line Input Modules Tone Generator ModulesLine Input Modules General Specifications Line Input ModulesGeneral Specifications Tone Generator Modules Tone GeneratorsBody Priority Input FacilitiesLocation of priority sequence setting switches FacilityMixer facility connector pin identification Page Power Amplifier Module Loudspeaker OutputMacro range installation manual. Issue Auxiliary Output Connection Power Supply Combining the INPUT/OUTPUT Facilities of TWO or More UnitsPriority connections for multiple amplifier systems AC & DC supply connections and monitoring Factory Fitted Options TB/ALC This is a Safety Earth and Must Never be DisregardedEarthing and HUM Loops TB/SPage Installation Page Fuses Repairs and MaintenanceWarranty Faults Symptoms and Checklist Fault Symptom ChecklistAppendix a Appendix B Appendix C Appendix D Appendix E

M250/SD, M1008/D, M1008, M100/S, M250/S specifications

The Mustang M1008, M2508, M250/SD, M/8M, and M100/S are a series of versatile aircraft designed to meet various operational needs in both civilian and military environments. These aircraft are known for their robust performance, advanced technologies, and user-friendly characteristics that make them suitable for tasks ranging from logistics to surveillance.

One of the main features of the Mustang M1008 is its efficient powerplant. It is equipped with a high-performance engine that delivers exceptional thrust and speed while maintaining fuel efficiency. This capability allows for extended ranges and longer flight durations, making it an ideal choice for long-haul missions. The M1008 has a spacious cabin designed for cargo transport, accommodating various payloads, and can be easily modified for different roles.

The M2508 variant incorporates advanced avionics and navigation systems, improving situational awareness for pilots. Its cutting-edge cockpit design offers a user-friendly interface, enhancing pilot control and reducing workload during complex operations. Additionally, the M2508 features enhanced safety systems, including redundant controls and automated flight systems, ensuring mission reliability even in challenging conditions.

The M250/SD model focuses on surveillance and reconnaissance applications. It is equipped with sophisticated imaging and sensor technologies that allow for real-time data collection and analysis. This capability is vital for military operations, providing ground forces with actionable intelligence and improving operational effectiveness. The M250/SD’s ability to adapt to different sensor suites makes it a valuable asset in various mission profiles.

The M/8M variant is notable for its versatility in various terrains. Its rugged design allows for impressive off-road capabilities, making it suitable for operations in remote and challenging environments. With reinforced landing gear and a spacious cargo bay, the M/8M can handle rough landings and transport heavy equipment, crucial for logistical support in the field.

Lastly, the M100/S emphasizes speed and agility, catering to urgent transport needs. This aircraft can operate in tighter spaces, enabling it to access locations that larger aircraft cannot. Its streamlined design minimizes drag, resulting in higher speeds and lower fuel consumption.

Overall, the Mustang M1008/D, M2508, M250/SD, M/8M, and M100/S deliver a combination of performance, versatility, and advanced technology, making them formidable options in their respective roles. Whether for logistics, surveillance, or both, these aircraft provide solutions that meet the demands of modern aviation.
Top Page Image Contents