Mustang M/8M, M2508/D, M100/SD, M1008/D, M250/SD Macro range installation manual. Issue

Page 15

MACRO range installation manual. Issue 6

Fig. 8 Power amplifier module fixings and adjustments

removing the 4BA nut on the left and lifting that end clear of the stud. The cover may now be swung round.100V output

The general concept of a 100V line loudspeaker system is that a quantity of 100V line loudspeakers are connected in parallel across the amplifier output terminals. The loudspeakers may be arranged in any order, any combination and if necessary, using any number of feeds from the amplifier. They may be grouped onto sub-circuits which may then be controlled by switching or group volume controls, etc., as required to suit the operational requirements of the system. Sub circuits may be dedicated to ëPage-onlyí operation and switched in by means of relays powered by the comprehensive MACRO current sinks. See APPENDIX C for typical arrangements.

The 100V line loudspeaker output terminals will deliver conventional full program content, i.e. all music and all paging/priority signals. For 100V line loads connect between the two outer terminals and for 50V line systems connect between the centre and right terminals.

All three 100V line output terminals fully floating, earth-free, and centre-tapped. This latter is useful in certain critical installations where careful balancing of the loudspeaker network may be necessary. The terminal marked ëCTí may be earthed to chassis if required.

Low impedance output

Power output to the loudspeaker load may be taken at low impedance (low Z) The terminals marked A-O-B present a very low impedance output across A-B and which is centre-tapped at O. These terminals are not specifically rated, but as a guide, the output impedance across the A-B terminals is in the order of 2 ohms. The centre-tap is a direct connection to 0V level (chassis, signal earth, and -24V).

Typical loudspeaker load arrangements

 

 

The following are acceptable examples of loudspeaker loading arrangements:

A

400 x 1/2 Watt 100 Volt line speakers =

200 Watts total load to the amplifier. Use a 250 Watt amplifier

B

200 x 1 Watt 100 Volt line speakers

=

200 Watts total load to the amplifier. Use a 250 Watt amplifier

C

2 x 50 Watt 100 Volt line speakers =

100 Watts total load to the amplifier: Use either a 100 Watt amplifier (or a 250 Watt

 

amplifier to allow for 150 Watts future development).

D12x 5 Watt 100 Volt line speakers = 60 Watts total load to the amplifier, and therefore 40 Watts spare capacity for future expansion if using a 100 Watt amplifier

E10 x 5 Watt, and 6 x 2 Watt 100 Volt line speakers = 50 + 12 Watts = 62 Watts total load to the amplifier. Use a 100 Watt amplifier.

F4 x 60 Watt units each tapped at 30 Watts, and 20 x 4 Watt units tapped as follows: 5 @ 4 Watt, 5 @ 2 Watt and 20 @ 0.5 Watt 100 Volt line speakers = 160 Watts total load and therefore 90 Watts spare capacity for future expansion or for final adjustments. Use a 250 Watt amplifier

See APPENDIX C for typical loudspeaker arrangements.

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Mustang Macro range installation manual. Issue Index Appendix a Appendix B Appendix C Appendix D Appendix E Introduction Slave Amplifiers General Specifications Mixer AmplifiersFront Panel Controls & Indicators Tone Control & Master Gain AdjustmentInput Module System Tone Generator Modules General Specifications Microphone Input ModulesMicrophone & Line Input Modules NON-PRIORITY ModulesTone Generators General Specifications Line Input ModulesGeneral Specifications Tone Generator Modules Line Input ModulesPriority Input Facilities BodyFacility Location of priority sequence setting switchesMixer facility connector pin identification Page Loudspeaker Output Power Amplifier ModuleMacro range installation manual. Issue Auxiliary Output Connection Combining the INPUT/OUTPUT Facilities of TWO or More Units Power SupplyPriority connections for multiple amplifier systems AC & DC supply connections and monitoring TB/S This is a Safety Earth and Must Never be DisregardedEarthing and HUM Loops Factory Fitted Options TB/ALCPage Installation Page Repairs and Maintenance WarrantyFuses Fault Symptom Checklist Faults Symptoms and ChecklistAppendix a Appendix B Appendix C Appendix D Appendix E

M250/SD, M1008/D, M1008, M100/S, M250/S specifications

The Mustang M1008, M2508, M250/SD, M/8M, and M100/S are a series of versatile aircraft designed to meet various operational needs in both civilian and military environments. These aircraft are known for their robust performance, advanced technologies, and user-friendly characteristics that make them suitable for tasks ranging from logistics to surveillance.

One of the main features of the Mustang M1008 is its efficient powerplant. It is equipped with a high-performance engine that delivers exceptional thrust and speed while maintaining fuel efficiency. This capability allows for extended ranges and longer flight durations, making it an ideal choice for long-haul missions. The M1008 has a spacious cabin designed for cargo transport, accommodating various payloads, and can be easily modified for different roles.

The M2508 variant incorporates advanced avionics and navigation systems, improving situational awareness for pilots. Its cutting-edge cockpit design offers a user-friendly interface, enhancing pilot control and reducing workload during complex operations. Additionally, the M2508 features enhanced safety systems, including redundant controls and automated flight systems, ensuring mission reliability even in challenging conditions.

The M250/SD model focuses on surveillance and reconnaissance applications. It is equipped with sophisticated imaging and sensor technologies that allow for real-time data collection and analysis. This capability is vital for military operations, providing ground forces with actionable intelligence and improving operational effectiveness. The M250/SD’s ability to adapt to different sensor suites makes it a valuable asset in various mission profiles.

The M/8M variant is notable for its versatility in various terrains. Its rugged design allows for impressive off-road capabilities, making it suitable for operations in remote and challenging environments. With reinforced landing gear and a spacious cargo bay, the M/8M can handle rough landings and transport heavy equipment, crucial for logistical support in the field.

Lastly, the M100/S emphasizes speed and agility, catering to urgent transport needs. This aircraft can operate in tighter spaces, enabling it to access locations that larger aircraft cannot. Its streamlined design minimizes drag, resulting in higher speeds and lower fuel consumption.

Overall, the Mustang M1008/D, M2508, M250/SD, M/8M, and M100/S deliver a combination of performance, versatility, and advanced technology, making them formidable options in their respective roles. Whether for logistics, surveillance, or both, these aircraft provide solutions that meet the demands of modern aviation.
Top Page Image Contents