Multiquip J36S60 Changing blades, Trowel arm removal, Remove the trowel arm from the spider plate

Page 34

maintenance

changing blades

It is recommended that ALL the blades on the trowel are changed at the same time. If only one or some of the blades are changed, the machine will not finish concrete consistently and the machine may wobble or bounce.

Perform the following procedure when changing blades: Please note the blade orientation on the trowel arm before removing.

1.Lift the trowel up, placing blocks under the main guard ring to support it.

2.Remove the bolts and lock washers from all the towel arms, and then remove the blades as shown in Figure 52.

BLADE

ATTACHMENT

SCREWS

TROWEL ARM

BLADE

ATTACHMENT

BAR

TROWEL

BLADE

Figure 52. Blade Removal

3.Wire brush and remove all concrete and debris from all six sides of each of the four trowel arms. This is important to properly seat the new blades.

4.Install the new blades, maintaining the proper blade orientation for direction of rotation.

5.Reinstall the bolts and lock washers.

Trowel arm removal

1.Each trowel arm is held in place at the spider plate by a hex head bolt (zerk grease fitting) and a roll pin. Remove both the hex head bolt and the roll pin (Figure 53) from the spider plate.

2.Remove the trowel arm from the spider plate.

3.Should the trowel arm inserts ( bushing ) come out with the trowel arm, remove the bushing from the trowel arm and set aside in a safe place. If the bushing is retained inside the spider plate, carefully remove the bushing

4.Examine the trowel arm bushing insert (Figure 53), clean if necessary. Replace bushing if out of round or worn.

SPIDER PLATE

ROLL PIN

TROWEL

ZERKARM

CAP GREASE FITTING

BUSHING

Figure 53. Trowel Arm Removal

page 34 — J36S60 WALK-BEHIND TROWEL • operation and parts manUAL — rev. #1 (01/23/13)

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents J36S60 WAKL-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation ChecklistSafety Information SaFeTy meSSageSGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy Before servicing equipmentFUeL SaFeTy TRaNSpORTINg SaFeTyEmission Control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeSound Power Level in dBA b Trowel SPECIFICATIONS/DIMENSIONSGuaranteed ISO 37442010 Based M/s 2 ∑A8Engine Specifications General information Trowel Components Engine Subaru 5.7 HP gasoline engineEngine Components Initial ServicingHandle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar PlacementFlat Safety Stop Switch ConnectionPitch Cable Installation Handle forward for no pitch blades flatBefore Starting InspectionEngine Oil Check Belt Guard Check Gearbox OilBelt Check Fuel CheckLifting the Trowel Onto a Slab Inspection/operationOperation Lifting BaleStarting the Engine OperationPlace the engine fuel valve lever in the on position Testing the Centrifugal Safety Stop Switch Choke Lever OpenPitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineClip-On Float Blades Optional OptionsCombo Blades Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance General Cleanliness Engine Air CleanerEngine check Belt Engine oilSpark Plug Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT- ChinaStandard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center BalanceGuard Assy SCREW, Fast Lead Guard Ring J36 FinisherWASHER, Flat SAE 5/16 GRD 9YZ WASHER, Fast Lead StainlessGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationBEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input ShaftEngine Assy Lifting Bale Assembly J FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic ClutchSpider Assy 14 1BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider PlateBlade Assy Float Disc Latch PIN Trowel BLADE, 8X14, ComboTrowel BLADE, 8X14, Finish Float PAN, 36-INCHEX17 crankcase assy OIL Seal Valve GuideStem Seal Ball BearingEX17 crankshaft assy Flange NUT Connecting ROD BoltCrankshaft CP Woodruff KEYEX17 muffler assy Ring Adjust ScrewPIN CAM Shaft PIN SpringEX17 air cleaner assy Label PackingCover CP Wing NUTEX17 governor assy Governor Shaft Spring AdjustGovernor Lever Governor ROD CPEX17 blower assy Case CP Blower Housing CPLabel Trade Mark HeadEX17 Recoil Starter assy Starter Rope Spiral SpringReel Starter KnobEX17 fuel tank assy Label Model Fuel Tank CPLabel Warning Fuel Tank CAP CPEX17 carburetor assy Pilot JET Throttle ValveChoke Valve Choke LeverEX17 ignition coil assy Flywheel CP Wire 1 CPSwitch Assy Ignition Coil CPEX17 oil sensor assy 740 20A0130400 700 2777630121OIL Sensor CP 780 20A0590100HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents