Multiquip J36S60 manual Spark arrester cleaning, Blade Pitch Adjustment Procedure

Page 32

maintenance

spark arrester cleaning

Clean the spark arrester every 6 months or 100 hours.

1.Remove the 4 mm screw (3) from the exhaust deflector, then remove the deflector. See Figure 46

2.Remove the 5 mm screw (4) from the muffler protector, then remove the muffler protector.

3.Remove the 4 mm screw from the spark arrestor, then remove the spark arrester.

Figure 46. Spark Arrester Removal

4.Carefully remove carbon deposits from the spark arrester screen (Figure 47) with a wire brush.

WIRE

BRUSH

SPARK

ARRESTER

SCREEN

Figure 47. Cleaning The Spark Arrester

5.If the spark arrester is damaged and has breaks or holes, replace with a new one.

6.Reinstall the spark arrester and muffler protector in reverse order of disassembly.

Blade Pitch Adjustment Procedure

The maintenance adjustment of blade pitch is an adjustment that is made by a bolt (Figure 48) on the arm of the trowel arm lever. This bolt is the contact point of the trowel arm lever to the lower wear plate on the thrust collar. The goal of the adjustment is to promote consistent blade pitch and finishing quality. Adjustments are made by tightening or loosening the blade pitch adjustment bolt.

BLADE PITCH

ADJUSTMENT

BOLT

TROWEL LEVER

FINGER

TROWEL

ARM

SPIDER

PLATE

TROWEL

BLADE

Figure 48. Blade Pitch Adjustment Bolt

Watch for the following indications when determining if blade pitch adjustments are necessary:

•Is the machine wearing out blades unevenly, (i.e. one blade is completely worn out while the others look new)?

•Does the machine have a perceptible rolling or bouncing motion when in use?

•Look at the machine while it is running, do the guard rings “rock up and down” relative to the ground?

If it is determined that blade pitch adjustments are required do the following:

1.Place the trowel on a flat, level area free of dirt and debris.

NOTICE

Before any blade pitch adjustments can be made it is essential to have a clean level area free of dirt and debris to test the trowel. Any unlevel spots in the floor or debris under the trowel blades will give an incorrect perception of adjustment. Ideally, a 5 x 5 ft. (1.5 x 1.5 meter), three-quarter inch (19 mm) thick FLAT steel plate should be used for testing.

page 32 — J36S60 WALK-BEHIND TROWEL • operation and parts manUAL — rev. #1 (01/23/13)

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents J36S60 WAKL-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation ChecklistSafety Information SaFeTy meSSageSGeNeRaL SaFeTy TROWeL SaFeTy ENgINe SaFeTyOrder Form PT-160 Before servicing equipmentFUeL SaFeTy TRaNSpORTINg SaFeTyENvIRONmeNTaL SaFeTy/DeCOmmISSIONINg EmISSIONS INFORmaTIONEmission Control Label Label must remain with the engine for its entire lifeTrowel SPECIFICATIONS/DIMENSIONS Guaranteed ISO 37442010 BasedSound Power Level in dBA b M/s 2 ∑A8Engine Specifications General information Trowel Components Engine Subaru 5.7 HP gasoline engineEngine Components Initial ServicingAssembly and installation Assembly and InstallationHandle Tube Installation Vibratory T-Handle Bar PlacementSafety Stop Switch Connection Pitch Cable InstallationFlat Handle forward for no pitch blades flatEngine Oil Check InspectionBefore Starting Gearbox Oil Belt CheckBelt Guard Check Fuel CheckInspection/operation OperationLifting the Trowel Onto a Slab Lifting BalePlace the engine fuel valve lever in the on position OperationStarting the Engine Testing the Centrifugal Safety Stop Switch Choke Lever OpenTo Begin Troweling Concrete Finishing TechniquesPitching the Blades Standard Handle Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineOptions Combo BladesClip-On Float Blades Optional Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance Engine check Engine Air CleanerGeneral Cleanliness Engine oil Spark PlugBelt Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsRemove the trowel arm from the spider plate Changing bladesTrowel arm removal Trowel arm Lever adjustment Checking trowel arm straightnessEnsure the fixture arm is in the up position Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, Read MANUAL, 2.00 DIA ISO DECAL, LIFTING/CRUSH, 2.4 XISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT- ChinaStandard Handle Assy Wire ASSY., Kill Switch Switch ASSY., KillSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option NUT , QP Trim Cntl Adjustment Adjustment PINQP Adjustment Block Spring Center BalanceGuard Assy Guard Ring J36 Finisher WASHER, Flat SAE 5/16 GRD 9YZSCREW, Fast Lead WASHER, Fast Lead StainlessGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationSEAL, OIL FLANGE, Input ShaftBEARING, CUP, Timken #M11910 GEAR, Worm B Input ShaftEngine Assy CONNECTOR, Splice TAP WIRE, Safety SwitchLifting Bale Assembly J FIN WEIGHT, Automatic ClutchSpider Assy 14 1Blade Assembly Lock Washer 3/8 MEDBUSHING, Trowel ARM Spider PlateBlade Assy Trowel BLADE, 8X14, Combo Trowel BLADE, 8X14, FinishFloat Disc Latch PIN Float PAN, 36-INCHEX17 crankcase assy Valve Guide Stem SealOIL Seal Ball BearingEX17 crankshaft assy Connecting ROD Bolt Crankshaft CPFlange NUT Woodruff KEYEX17 muffler assy Adjust Screw PIN CAM ShaftRing PIN SpringEX17 air cleaner assy Packing Cover CPLabel Wing NUTEX17 governor assy Spring Adjust Governor LeverGovernor Shaft Governor ROD CPEX17 blower assy Blower Housing CP Label Trade MarkCase CP HeadEX17 Recoil Starter assy Spiral Spring ReelStarter Rope Starter KnobEX17 fuel tank assy Fuel Tank CP Label WarningLabel Model Fuel Tank CAP CPEX17 carburetor assy Throttle Valve Choke ValvePilot JET Choke LeverEX17 ignition coil assy Wire 1 CP Switch AssyFlywheel CP Ignition Coil CPEX17 oil sensor assy 700 2777630121 OIL Sensor CP740 20A0130400 780 20A0590100HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents