Multiquip J36S60 manual FUeL SaFeTy, TRaNSpORTINg SaFeTy

Page 10

Safety Information

NOTICE

„NeveR run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter frequently to prevent engine malfunction.

„NeveR tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.

FUeL SaFeTy

DaNgeR

„DO NOT add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fi re due to static electricity.

FUEL

FUEL

„DO NOT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited.

„aLWayS refuel in a well-ventilated area, away from sparks and open fl ames.

„aLWayS use extreme caution when working with flammable liquids.

„DO NOT fi ll the fuel tank while the engine is running or hot.

„DO NOT overfi ll tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.

„Store fuel in appropriate containers, in well-ventilated areas and away from sparks and fl ames.

„NeveR use fuel as a cleaning agent.

„DO NOT smoke around or near the equipment. Fire or explosion could result from fuel vapors or if fuel is spilled on a hot engine.

TRaNSpORTINg SaFeTy

CaUTION

„NeveR allow any person or animal to stand underneath the equipment while lifting.

NOTICE

„Some walk-behind trowels can be lifted or moved by two people utilizing lifting tubes or other special attachments. Generally, however, they must be lifted using lifting bales and cranes, hoists, or forklifts.

„NeveR transport trowel with fl oat pans attached unless safety catches are used and are specifi cally cleared for such transport by the manufacturer.

„NeveR hoist the trowel more than three feet off the ground with fl oat pans attached.

„Before lifting, make sure that the lifting bales are not damaged.

„Always make sure crane or lifting device has been properly secured to the lifting bales of the equipment.

„aLWayS shutdown engine before transporting.

„NeveR lift the equipment while the engine is running.

„Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

„Use adequate lifting cable (wire or rope) of suffi cient strength.

„DO NOT lift machine to unnecessary heights.

„aLWayS tie down equipment during transport by securing the equipment with rope.

page 10 — J36S60 WALK-BEHIND TROWEL • operation and parts manUAL — rev. #1 (01/23/13)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents J36S60 WAKL-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation ChecklistSafety Information SaFeTy meSSageSGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy Before servicing equipmentFUeL SaFeTy TRaNSpORTINg SaFeTyEmission Control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeSound Power Level in dBA b Trowel SPECIFICATIONS/DIMENSIONSGuaranteed ISO 37442010 Based M/s 2 ∑A8Engine Specifications General information Trowel Components Engine Subaru 5.7 HP gasoline engineEngine Components Initial ServicingHandle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar PlacementFlat Safety Stop Switch ConnectionPitch Cable Installation Handle forward for no pitch blades flatBefore Starting InspectionEngine Oil Check Belt Guard Check Gearbox OilBelt Check Fuel CheckLifting the Trowel Onto a Slab Inspection/operationOperation Lifting BaleStarting the Engine OperationPlace the engine fuel valve lever in the on position Testing the Centrifugal Safety Stop Switch Choke Lever OpenPitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineClip-On Float Blades Optional OptionsCombo Blades Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance General Cleanliness Engine Air CleanerEngine check Belt Engine oilSpark Plug Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT- ChinaStandard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center BalanceGuard Assy SCREW, Fast Lead Guard Ring J36 FinisherWASHER, Flat SAE 5/16 GRD 9YZ WASHER, Fast Lead StainlessGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationBEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input ShaftEngine Assy Lifting Bale Assembly J FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic ClutchSpider Assy 14 1BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider PlateBlade Assy Float Disc Latch PIN Trowel BLADE, 8X14, ComboTrowel BLADE, 8X14, Finish Float PAN, 36-INCHEX17 crankcase assy OIL Seal Valve GuideStem Seal Ball BearingEX17 crankshaft assy Flange NUT Connecting ROD BoltCrankshaft CP Woodruff KEYEX17 muffler assy Ring Adjust ScrewPIN CAM Shaft PIN SpringEX17 air cleaner assy Label PackingCover CP Wing NUTEX17 governor assy Governor Shaft Spring AdjustGovernor Lever Governor ROD CPEX17 blower assy Case CP Blower Housing CPLabel Trade Mark HeadEX17 Recoil Starter assy Starter Rope Spiral SpringReel Starter KnobEX17 fuel tank assy Label Model Fuel Tank CPLabel Warning Fuel Tank CAP CPEX17 carburetor assy Pilot JET Throttle ValveChoke Valve Choke LeverEX17 ignition coil assy Flywheel CP Wire 1 CPSwitch Assy Ignition Coil CPEX17 oil sensor assy 740 20A0130400 700 2777630121OIL Sensor CP 780 20A0590100HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents