Multiquip J36S60 manual Inspection, Before Starting, Engine Oil Check

Page 19

inspection

BLADE

PITCH

CABLE

YOKE

YOKE

EYELET

BRASS SET

BRASS SET

NUT #1

NUT #2

 

4.Align the groove on the slider with the text 36" COMBO/ "J" COMBO on the decal. The letter "J" stands for J-36 Walk-Behind Trowel

CAUTION

ALWAYS wear approved eye and hearing protection before operating the trowel.

NEVER place hands or feet inside the guard rings while the engine is running. ALWAYS shut the engine down before performing any kind of maintenance service on the trowel.

Figure 12. Pitch Cable Yoke Attachment

6.Using a wrench, tighten the brass set #2 nut up against the yoke boss. This will lock the cable in place.

7.Use a wrench and finish tightening the brass set #1 nut up against the yoke boss.

Pre-Load Adjustment (Quick Pitch™ Handle Only)

WARNING

The Quick Pitch™ handle is spring loaded, personal injury or damage could result from improper handling, installation or adjustment. Use extreme caution when installing this component.

1.After the Quick-Pitch™ handle has been installed on the trowel, spring pre-load adjustment will be required.

2.Locate the spring pre-load adjustment screw (Figure 13) on the underside of the handle tube.

ALIGNMENT

DECAL

FINISH

J

COMBO

FINISH

J

COMBO

PRELOAD TRIM INDICATOR

FINISH

36”

COMBO

FINISH

48”

COMBO

 

ADJUSTMENT

J

SCREW

 

48”

J

SLIDER

36”

 

GROOVE

Before Starting

1.Read all safety instructions at the beginning of manual.

2.Clean the trowel, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner.

3.Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

4.Check carburetor for external dirt and dust. Clean with dry compressed air.

5.Check fastening nuts and bolts for tightness.

Engine Oil Check

1.To check the engine oil level, place the trowel on secure level ground with the engine stopped.

2.Remove the dipstick from the engine oil filler hole (Figure 14) and wipe clean.

Figure 14. Engine Oil Dipstick Removal Figure 13. Spring Pre-Load Adjustment

3.A decal has been placed on the side of the handle tube to assist the user in the adjustment of the spring.

j36s60 WALK-BEHIND TROWEL • operatION And parts manual — rev. #1 (01/23/13) — page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsJ36S60 WAKL-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160TRaNSpORTINg SaFeTy FUeL SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelM/s 2 ∑A8 Trowel SPECIFICATIONS/DIMENSIONSGuaranteed ISO 37442010 Based Sound Power Level in dBA bEngine Specifications General information Engine Subaru 5.7 HP gasoline engine Trowel ComponentsInitial Servicing Engine ComponentsVibratory T-Handle Bar Placement Assembly and installationAssembly and Installation Handle Tube InstallationHandle forward for no pitch blades flat Safety Stop Switch ConnectionPitch Cable Installation FlatBefore Starting InspectionEngine Oil Check Fuel Check Gearbox OilBelt Check Belt Guard CheckLifting Bale Inspection/operationOperation Lifting the Trowel Onto a SlabStarting the Engine OperationPlace the engine fuel valve lever in the on position Choke Lever Open Testing the Centrifugal Safety Stop SwitchPitching the Blades Quick Pitch Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Standard HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionFloat Discs Optional OptionsCombo Blades Clip-On Float Blades OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance General Cleanliness Engine Air CleanerEngine check Never use a spark plug of incorrect heat range Engine oilSpark Plug BeltBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Shaft and the test surface Trowel arm Lever adjustmentChecking trowel arm straightness Ensure the fixture arm is in the up positionInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals DECAL, Serial PLATE, WBT- China ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, ASK for TRAINING, 2.00 DIAStandard Handle Assy WASHER, FENDER, 1.5OD X 3/8ID Wire ASSY., Kill SwitchSwitch ASSY., Kill SPACER, Slide Block GuideQuick-pitch Handle ASSY. option Spring Center Balance NUT , QP Trim Cntl AdjustmentAdjustment PIN QP Adjustment BlockGuard Assy WASHER, Fast Lead Stainless Guard Ring J36 FinisherWASHER, Flat SAE 5/16 GRD 9YZ SCREW, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyGEAR, Worm B Input Shaft SEAL, OILFLANGE, Input Shaft BEARING, CUP, Timken #M11910Engine Assy WEIGHT, Automatic Clutch CONNECTOR, Splice TAPWIRE, Safety Switch Lifting Bale Assembly J FIN14 1 Spider AssySpider Plate Blade AssemblyLock Washer 3/8 MED BUSHING, Trowel ARMBlade Assy Float PAN, 36-INCH Trowel BLADE, 8X14, ComboTrowel BLADE, 8X14, Finish Float Disc Latch PINEX17 crankcase assy Ball Bearing Valve GuideStem Seal OIL SealEX17 crankshaft assy Woodruff KEY Connecting ROD BoltCrankshaft CP Flange NUTEX17 muffler assy PIN Spring Adjust ScrewPIN CAM Shaft RingEX17 air cleaner assy Wing NUT PackingCover CP LabelEX17 governor assy Governor ROD CP Spring AdjustGovernor Lever Governor ShaftEX17 blower assy Head Blower Housing CPLabel Trade Mark Case CPEX17 Recoil Starter assy Starter Knob Spiral SpringReel Starter RopeEX17 fuel tank assy Fuel Tank CAP CP Fuel Tank CPLabel Warning Label ModelEX17 carburetor assy Choke Lever Throttle ValveChoke Valve Pilot JETEX17 ignition coil assy Ignition Coil CP Wire 1 CPSwitch Assy Flywheel CPEX17 oil sensor assy 780 20A0590100 700 2777630121OIL Sensor CP 740 20A0130400HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents