Multiquip J36S60 manual Trowel Components, Engine Subaru 5.7 HP gasoline engine

Page 15

trowel COMPONENTS

4 5

3

2

10 9

1

15 14 13 12 11

Figure 2. Trowel Control and Components

Figure 2 shows the location of the basic controls or components, for the trowel. Listed below is a brief explanation of each control or component.

1.Access Panel — Allows access to the blade area. NEVER run the trowel with this access panel removed.

2.Engine — Subaru 5.7 HP gasoline engine.

3.Lifting Bale — Attach a suitable lifting device to lifting bale whenever lifting of the trowel is required.

4.Throttle Lever — Controls engine speed. Returns engine to idle when released.

5.Vibratory Handle Bar — Installed rubber shock mounts/isolators reduces vibration when the trowel is operating.

6.Pitch Control Star Wheel— To adjust the pitch of the blades, rotate the star wheel clockwise to pitch blades upwards. Rotate star wheel counterclockwise to pitch blades flat (no pitch).

7.Handle Bar Pad — Foam rubber pad that protects the body when coming in contact with handle bar.

8.Hand Grips — When maneuvering of the trowel is required ALWAYS place both hands on each grip to operate the trowel. Replace hand grips when they become worn or damaged.

6 7 8

16

QUICK PITCH ™

HANDLE (OPTION)

9.Handlebar Adjuster — Change the angle/height of the handle bars by loosening star wheel, adjust handlebars to desired location, tighten starwheel firmly to hold handlebars in that position.

10.Centrifugal "Kill" Switch — In the event the operator loses control of the trowel, this switch will shut down the engine.

11.Blades — This trowel is equipped with combination blades. These blades are versatile and should take care of most troweling needs. In addition float discs can be attached to the trowel arms that will allow the trowel to float on "wet" concrete.

12.V-Belt Cover — Remove this cover to gain access to the V-belt. NEVER operate the trowel with this cover removed.

13.Guard Ring — NEVER put hands or feet inside guard ring while the machine is running.

14.Gearbox — Helical worm gear drive gearbox. Provides rotation of blades via engine interface. ALWAYS check gearbox oil level (sight glass) prior to each use. Fill with recommended type gearbox oil.

15.Trowel Arm — NEVER operate the trowel with a bent, broken or out of adjustment trowel arm. If the blades show uneven wear patterns or some blades wear out faster than others, the trowel arm may need to be adjusted. Use the trowel arm adjustment tool P/N 1817 to adjust the trowel arms.

16.Quick Pitch™ Control Handle — Contact MQ unit sales for this option.

j36s60 WALK-BEHIND TROWEL • operatION And parts manual — rev. #1 (01/23/13) — page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsJ36S60 WAKL-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160TRaNSpORTINg SaFeTy FUeL SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelM/s 2 ∑A8 Trowel SPECIFICATIONS/DIMENSIONSGuaranteed ISO 37442010 Based Sound Power Level in dBA bEngine Specifications General information Engine Subaru 5.7 HP gasoline engine Trowel ComponentsInitial Servicing Engine ComponentsVibratory T-Handle Bar Placement Assembly and installationAssembly and Installation Handle Tube InstallationHandle forward for no pitch blades flat Safety Stop Switch ConnectionPitch Cable Installation FlatInspection Before StartingEngine Oil Check Fuel Check Gearbox OilBelt Check Belt Guard CheckLifting Bale Inspection/operationOperation Lifting the Trowel Onto a SlabOperation Starting the EnginePlace the engine fuel valve lever in the on position Choke Lever Open Testing the Centrifugal Safety Stop SwitchPitching the Blades Quick Pitch Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Standard HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionFloat Discs Optional OptionsCombo Blades Clip-On Float Blades OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Never use a spark plug of incorrect heat range Engine oilSpark Plug BeltBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalChanging blades Trowel arm removalRemove the trowel arm from the spider plate Shaft and the test surface Trowel arm Lever adjustmentChecking trowel arm straightness Ensure the fixture arm is in the up positionInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals DECAL, Serial PLATE, WBT- China ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, ASK for TRAINING, 2.00 DIAStandard Handle Assy WASHER, FENDER, 1.5OD X 3/8ID Wire ASSY., Kill SwitchSwitch ASSY., Kill SPACER, Slide Block GuideQuick-pitch Handle ASSY. option Spring Center Balance NUT , QP Trim Cntl AdjustmentAdjustment PIN QP Adjustment BlockGuard Assy WASHER, Fast Lead Stainless Guard Ring J36 FinisherWASHER, Flat SAE 5/16 GRD 9YZ SCREW, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyGEAR, Worm B Input Shaft SEAL, OILFLANGE, Input Shaft BEARING, CUP, Timken #M11910Engine Assy WEIGHT, Automatic Clutch CONNECTOR, Splice TAPWIRE, Safety Switch Lifting Bale Assembly J FIN14 1 Spider AssySpider Plate Blade AssemblyLock Washer 3/8 MED BUSHING, Trowel ARMBlade Assy Float PAN, 36-INCH Trowel BLADE, 8X14, ComboTrowel BLADE, 8X14, Finish Float Disc Latch PINEX17 crankcase assy Ball Bearing Valve GuideStem Seal OIL SealEX17 crankshaft assy Woodruff KEY Connecting ROD BoltCrankshaft CP Flange NUTEX17 muffler assy PIN Spring Adjust ScrewPIN CAM Shaft RingEX17 air cleaner assy Wing NUT PackingCover CP LabelEX17 governor assy Governor ROD CP Spring AdjustGovernor Lever Governor ShaftEX17 blower assy Head Blower Housing CPLabel Trade Mark Case CPEX17 Recoil Starter assy Starter Knob Spiral SpringReel Starter RopeEX17 fuel tank assy Fuel Tank CAP CP Fuel Tank CPLabel Warning Label ModelEX17 carburetor assy Choke Lever Throttle ValveChoke Valve Pilot JETEX17 ignition coil assy Ignition Coil CP Wire 1 CPSwitch Assy Flywheel CPEX17 oil sensor assy 780 20A0590100 700 2777630121OIL Sensor CP 740 20A0130400HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents