Multiquip J36S60 manual Air cleaner dirty? Clean or replace air cleaner

Page 39

 

 

troubleshooting

 

 

 

 

 

 

 

 

 

Troubleshooting (engine) - continued

 

 

Symptom

possible problem

 

Solution

 

Air cleaner dirty?

 

Clean or replace air cleaner.

Weak in power, compression is proper and

Improper level in carburetor?

 

Check fl oat adjustment, rebuild carburetor.

does not misfi re.

Defective spark plug?

 

Clean or replace spark plug.

 

Improper spark plug?

 

Set to proper gap.

 

Water in fuel system?

 

Flush fuel system and replace with correct

Weak in power, compression is proper but

 

type of fuel.

 

 

 

 

 

misfi res.

Dirty spark plug?

 

Clean or replace spark plug.

 

 

 

 

 

Ignition coil defective?

 

Replace ignition coil.

 

 

 

 

 

Spark plug heat value incorrect?

 

Replace with correct type of spark plug.

 

 

 

 

 

Wrong type of fuel?

 

Replace with correct type of fuel.

 

 

 

 

Engine overheats.

Cooling fi ns dirty?

 

Clean cooling fi ns.

 

 

 

Intake air restricted?

 

Clear intake of dirt and debris. Replace air

 

 

 

 

cleaner elements as necessary.

 

 

 

 

 

 

 

 

Oil level too low or too high?

 

Adjust oil to proper level.

 

 

 

 

 

Governor adjusted incorrectly?

 

Adjust governor.

 

 

 

 

Rotational speed fl uctuates.

Governor spring defective?

 

Replace governor spring.

 

 

 

 

 

Fuel fl ow restricted?

 

Check entire fuel system for leaks or clogs.

 

 

 

 

Recoil starter malfunctions. (if applicable)

Recoil mechanism clogged with dust and dirt?

 

Clean recoil assembly with soap and water.

 

 

 

Spiral spring loose?

 

Replace spiral spring.

 

 

 

 

 

 

 

Loose, damaged wiring?

 

Ensure tight, clean connections on battery

 

 

and starter.

Starter malfunctions.

 

 

 

 

 

Battery insuffi ciently charged?

 

Recharge or replace battery.

 

 

 

 

 

 

 

Starter damaged or internally shorted?

 

Replace starter.

 

 

 

 

 

Over-accumulation of exhaust products?

 

Check and clean valves. Check muffl er and

 

 

replace if necessary.

Burns too much fuel.

 

 

 

 

 

Wrong spark plug?

 

Replace spark plug with manufacturer's

 

 

 

 

suggested type.

 

 

 

Exhaust color is continuously "white".

Lubricating oil is wrong viscosity?

 

Replace lubricating oil with correct viscosity.

Worn rings?

 

Replace rings.

 

 

 

Air cleaner clogged?

 

Clean or replace air cleaner.

 

Choke valve set to incorrect position?

 

Adjust choke valve to correct position.

Exhaust color is continuously "black".

Carburetor defective, seal on carburetor

 

Replace carburetor or seal.

broken?

 

 

 

 

 

Poor carburetor adjustment, engine runs too

 

Adjust carburetor.

 

rich?

 

 

 

 

 

ON/OFF device not activated ON?

 

Turn on ON/OFF device.

Will not start, no power with key "ON". (if

Battery disconnected or discharged?

 

Check cable connections. Charge or replace

applicable)

 

battery

 

 

 

Ignition switch/wiring defective?

 

Replace ignition switch. Check wiring.

j36s60 WALK-BEHIND TROWEL • operatION And parts manual — rev. #1 (01/23/13) — page 39

Image 39
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsJ36S60 WAKL-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160TRaNSpORTINg SaFeTy FUeL SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelM/s 2 ∑A8 Trowel SPECIFICATIONS/DIMENSIONSGuaranteed ISO 37442010 Based Sound Power Level in dBA bEngine Specifications General information Engine Subaru 5.7 HP gasoline engine Trowel ComponentsInitial Servicing Engine ComponentsVibratory T-Handle Bar Placement Assembly and installationAssembly and Installation Handle Tube InstallationHandle forward for no pitch blades flat Safety Stop Switch ConnectionPitch Cable Installation FlatInspection Before StartingEngine Oil Check Fuel Check Gearbox OilBelt Check Belt Guard CheckLifting Bale Inspection/operationOperation Lifting the Trowel Onto a SlabOperation Starting the EnginePlace the engine fuel valve lever in the on position Choke Lever Open Testing the Centrifugal Safety Stop SwitchPitching the Blades Quick Pitch Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Standard HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionFloat Discs Optional OptionsCombo Blades Clip-On Float Blades OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Never use a spark plug of incorrect heat range Engine oilSpark Plug BeltBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalChanging blades Trowel arm removalRemove the trowel arm from the spider plate Shaft and the test surface Trowel arm Lever adjustmentChecking trowel arm straightness Ensure the fixture arm is in the up positionInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals DECAL, Serial PLATE, WBT- China ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, ASK for TRAINING, 2.00 DIAStandard Handle Assy WASHER, FENDER, 1.5OD X 3/8ID Wire ASSY., Kill SwitchSwitch ASSY., Kill SPACER, Slide Block GuideQuick-pitch Handle ASSY. option Spring Center Balance NUT , QP Trim Cntl AdjustmentAdjustment PIN QP Adjustment BlockGuard Assy WASHER, Fast Lead Stainless Guard Ring J36 FinisherWASHER, Flat SAE 5/16 GRD 9YZ SCREW, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyGEAR, Worm B Input Shaft SEAL, OILFLANGE, Input Shaft BEARING, CUP, Timken #M11910Engine Assy WEIGHT, Automatic Clutch CONNECTOR, Splice TAPWIRE, Safety Switch Lifting Bale Assembly J FIN14 1 Spider AssySpider Plate Blade AssemblyLock Washer 3/8 MED BUSHING, Trowel ARMBlade Assy Float PAN, 36-INCH Trowel BLADE, 8X14, ComboTrowel BLADE, 8X14, Finish Float Disc Latch PINEX17 crankcase assy Ball Bearing Valve GuideStem Seal OIL SealEX17 crankshaft assy Woodruff KEY Connecting ROD BoltCrankshaft CP Flange NUTEX17 muffler assy PIN Spring Adjust ScrewPIN CAM Shaft RingEX17 air cleaner assy Wing NUT PackingCover CP LabelEX17 governor assy Governor ROD CP Spring AdjustGovernor Lever Governor ShaftEX17 blower assy Head Blower Housing CPLabel Trade Mark Case CPEX17 Recoil Starter assy Starter Knob Spiral SpringReel Starter RopeEX17 fuel tank assy Fuel Tank CAP CP Fuel Tank CPLabel Warning Label ModelEX17 carburetor assy Choke Lever Throttle ValveChoke Valve Pilot JETEX17 ignition coil assy Ignition Coil CP Wire 1 CPSwitch Assy Flywheel CPEX17 oil sensor assy 780 20A0590100 700 2777630121OIL Sensor CP 740 20A0130400HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.