Multiquip J36S60 TROWeL SaFeTy, ENgINe SaFeTy, Order Form PT-160, Before servicing equipment

Page 9
DANGEROUS
GAS FUMES

Safety Information

TROWeL SaFeTy

DaNgeR

„Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

„The engine of this equipment requires an adequate free fl ow of cooling air. NeveR operate this equipment in any enclosed or narrow area

where free fl ow of the air is restricted. If the air fl ow is

restricted it will cause injury to people and property and serious damage to the equipment or engine.

„NeveR operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fi re could result causing severe bodily harm or even death.

WaRNINg

„aLWayS keep clear of rotating or moving

parts while operating the trowel.

„DO NOT start or operate the trowel if the drive train will not disengage. Centrifugal

force between the trowel and surface when starting can cause uncontrolled handle movement that can cause serious injury. The handle must not move while pulling the engine recoil starter.

„NeveR disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

CaUTION

„NeveR stand on trowel during operation.

„NeveR lubricate components or attempt service on a running machine.

„NeveR place your feet or hands inside the guard rings while starting or operating this equipment.

NOTICE

„aLWayS keep the machine in proper running condition.

„Fix damage to machine and replace any broken parts immediately.

„aLWayS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

„A safety manual for operating and maintenance personnel of concrete power trowels produced by the Association of Equipment Manufacturers (AEM) can be obtained for a fee by ordering through their website at www.aem.org.

Order FORM PT-160

eNgINe SaFeTy

WaRNINg

„DO NOT place hands or fingers inside engine compartment when engine is running.

„NeveR operate the engine with heat shields or guards removed.

„Keep fi ngers, hands hair and clothing away from all moving parts to prevent injury.

„DO NOT remove the radiator cap while the

engine is hot. High pressure boiling water will gush out of the radiator and severely scald any persons in the general area of the trowel.

„DO NOT remove the coolant drain plug while the engine is hot. Hot coolant will gush out of the coolant tank and severely scald any persons in the general area of the trowel.

„DO NOT remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the trowel.

CaUTION

„NeveR touch the hot exhaust manifold, muffl er or cylinder. Allow these parts to cool

before servicing equipment.

j36s60 WALK-BEHIND TROWEL • operatION And parts manual — rev. #1 (01/23/13) — page 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model j36s60 Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsJ36S60 WAKL-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy ENgINe SaFeTy TROWeL SaFeTyOrder Form PT-160 Before servicing equipmentTRaNSpORTINg SaFeTy FUeL SaFeTyEmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmission Control Label Label must remain with the engine for its entire lifeGuaranteed ISO 37442010 Based Trowel SPECIFICATIONS/DIMENSIONSSound Power Level in dBA b M/s 2 ∑A8Engine Specifications General information Engine Subaru 5.7 HP gasoline engine Trowel ComponentsInitial Servicing Engine ComponentsAssembly and Installation Assembly and installationHandle Tube Installation Vibratory T-Handle Bar PlacementPitch Cable Installation Safety Stop Switch ConnectionFlat Handle forward for no pitch blades flatInspection Before StartingEngine Oil Check Belt Check Gearbox OilBelt Guard Check Fuel CheckOperation Inspection/operationLifting the Trowel Onto a Slab Lifting BaleOperation Starting the EnginePlace the engine fuel valve lever in the on position Choke Lever Open Testing the Centrifugal Safety Stop SwitchConcrete Finishing Techniques To Begin TrowelingPitching the Blades Standard Handle Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionCombo Blades OptionsClip-On Float Blades Optional Float Discs OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Spark Plug Engine oilBelt Never use a spark plug of incorrect heat rangeBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalChanging blades Trowel arm removalRemove the trowel arm from the spider plate Checking trowel arm straightness Trowel arm Lever adjustmentEnsure the fixture arm is in the up position Shaft and the test surfaceInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals ISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT- ChinaStandard Handle Assy Switch ASSY., Kill Wire ASSY., Kill SwitchSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option Adjustment PIN NUT , QP Trim Cntl AdjustmentQP Adjustment Block Spring Center BalanceGuard Assy WASHER, Flat SAE 5/16 GRD 9YZ Guard Ring J36 FinisherSCREW, Fast Lead WASHER, Fast Lead StainlessRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyFLANGE, Input Shaft SEAL, OILBEARING, CUP, Timken #M11910 GEAR, Worm B Input ShaftEngine Assy WIRE, Safety Switch CONNECTOR, Splice TAPLifting Bale Assembly J FIN WEIGHT, Automatic Clutch14 1 Spider AssyLock Washer 3/8 MED Blade AssemblyBUSHING, Trowel ARM Spider PlateBlade Assy Trowel BLADE, 8X14, Finish Trowel BLADE, 8X14, ComboFloat Disc Latch PIN Float PAN, 36-INCHEX17 crankcase assy Stem Seal Valve GuideOIL Seal Ball BearingEX17 crankshaft assy Crankshaft CP Connecting ROD BoltFlange NUT Woodruff KEYEX17 muffler assy PIN CAM Shaft Adjust ScrewRing PIN SpringEX17 air cleaner assy Cover CP PackingLabel Wing NUTEX17 governor assy Governor Lever Spring AdjustGovernor Shaft Governor ROD CPEX17 blower assy Label Trade Mark Blower Housing CPCase CP HeadEX17 Recoil Starter assy Reel Spiral SpringStarter Rope Starter KnobEX17 fuel tank assy Label Warning Fuel Tank CPLabel Model Fuel Tank CAP CPEX17 carburetor assy Choke Valve Throttle ValvePilot JET Choke LeverEX17 ignition coil assy Switch Assy Wire 1 CPFlywheel CP Ignition Coil CPEX17 oil sensor assy OIL Sensor CP 700 2777630121740 20A0130400 780 20A0590100HERE’S HOW to GET Help

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents