Manuals / Brands / Computer Equipment / Scanner / Measurement Specialties / Computer Equipment / Scanner

Measurement Specialties 9116 Our Company, Our Warranty, Technical Support, Merchandise Return Procedures

1 143

Download 143 pages, 1.86 Mb

Pressure Systems, Inc. Model 9116 User’s Manual

Page vii www.PressureSystems.com

Our Company

Pressure Systems Incorporated, (PSI) develops, manufactures, and services level and pressure

measuring instruments where the highest level of traceable accuracy is required for aerospace,

industrial, municipal, and environmental applications. Our products have become the world

standard for electronic level and pressure measurement and scanning. We are committed to

the highest quality design, manufacture, and support of level and pressure instrumentation that

is in the best interest of our customers. PSI is an ISO-9001:2000 certified company.

Our Warranty

Pressure Systems, Inc., warrants NetScanner™ System products to be free of defects in

material and workmanship under normal use and service for one (1) year.

Technical Support

Monday through Friday, during normal working hours, (7:30 am through 5:30 pm, Eastern time)

knowledgeable personnel are available for assistance and troubleshooting. Contact the

Applications Support Group or the Customer Services Department at Pressure Systems

(757-865-1243 or toll free 1-800-328-3665) if your scanner is not operating properly or if you

have questions concerning any of our products. E-mail assistance is available by contacting

Applications@PressureSystems.com.

Merchandise Return Procedures

If your scanner needs to be returned to Pressure Systems, obtain a Returned Merchandise

Authorization (RMA) from the Customer Service Department.

Be prepared to supply the following information when requesting the RMA:

• Part number

• Serial number

• Complete description of problems/symptoms

• Bill To and Ship To address

• Purchase order number (not required by PSI warranty repairs)

• Customer contact and telephone number

The above information, including the RMA number must be on the customer’s shipping

documents that accompany the equipment to be repaired. PSI also requests that the outside of

the shipping container be labeled with the RMA number to assist in tracking the repairs. All

equipment should be sent to the following address:

ATTN: PSI REPAIR DEPARTMENT (7-digit RMA number)

Pressure Systems, Inc.

34 Research Drive

Hampton, Virginia 23666

Contents

Main Page Table of Contents Page Page Page Preface Our Company Our Warranty Technical Support Merchandise Return Procedures Website and E-Mail Our Firmware Our Publication Disclaimer Chapter 1 General Information 1.1 Introduction 1.2 Description of the Instrument 1.2.1 Differences Between Models 9016 and 9116 Page 1.3 Options 1.3.1 Pressure Ranges 1.3.2 Manifolds and Pressure Connections 1.3.3 Communication Interfaces 2.2 Safety Considerations 2.3 Preparation for Use 2.3.1 Environment 2.3.2 Power 2.3.3 Mounting and Module Dimensions 2.3.4 Network Communications Hookup Page Note Page 2.3.5 Diagnostic Port Hookup 2.3.6 Pressure Connections Page Page Page 2.3.7 Case Grounding 2.3.8 Trigger Input Signal 2.3.9 Power Up Checks and Self-Diagnostics Chapter 3 Programming and Operation 3.1 Commands & Responses 3.1.1 Introduction 3.1.2 Commands Page Page 3.1.3 Responses 3.1.4 Functional Command Overview Page Page Page Page 3.2 Detailed Command Description Reference POWER UP CLEAR (Command A) RESET (Command B) CONFIGURE/CONTROL MULTI-POINT CALIBRATION (Command C) Command C Sub-command Index 00: Configure & Start Multi-Point Calibration Command C Sub-command Index 01: Collect Data for a Calibration Point Supply each of the previously-specified three (3) pressure calibration points to the Multi- Command C- Sub-command Index 02: Calculate & Apply Correction Coefficients Page Command C Sub-command Index 03: Abort Multi-Point Calibration READ TRANSDUCER VOLTAGES (Command V) Page CALCULATE AND SET GAINS (Command Z) Page READ TRANSDUCER A/D COUNTS (Command a) Page Page DEFINE/CONTROL AUTONOMOUS HOST STREAMS (Command c) Page Command c Sub-command Index 00: Configure A Host Delivery Stream Page Page Configure three (3) separate autonomous host delivery streams, and divide the modules Command c Sub-command Index 01: Start Stream(s) Command c Sub-command Index 02: Stop Stream(s) Command c Sub-command Index 03: Clear Stream(s) Stop all the streams configured previously. Then clear (un-define) only stream 3. Command c Sub-command Index 04: Return Stream Information Return configuration information for stream l Command c Sub-command Index 05: Select Data in a Stream Page Command c Sub-command Index 06: Select Protocol For Stream Delivery Configure all streams to be delivered via UDP/IP protocol. Host expects the UDP CALCULATE AND SET OFFSETS (Command h) READ TEMPERATURE COUNTS (Command m) READ TEMPERATURE VOLTAGES (Command n) READ MODULE STATUS (Command q) hhhh is a 4-digit hex datum (or other (**) decimal datum Page READ HIGH-PRECISION DATA (Command r) READ TRANSDUCER TEMPERATURE (Command t) READ INTERNAL COEFFICIENTS (Command u) Page Page DOWNLOAD INTERNAL COEFFICIENTS (Command v) Page Send TCP/IP command to module (i.e., via its connected socket): with SET/DO OPERATING OPTIONS/FUNCTIONS (Command w) Page Page NETWORK QUERY (UDP/IP Command psi9000) Query all module(s) on the network. RE-BOOT MODULE (UDP/IP Command psireboot) CHANGE MODULES IP ADDRESS RESOLUTION METHOD & RE-BOOT (UDP/IP Command psirarp) Chapter 4 Calibration 4.1 Introduction Page 4.2 Re-zero Calibration 4.2.1. Re-zero Calibration Valve Control 4.2.2 Re-zero Calibration Summary 4.3 Span Calibration 4.3.1. Span Calibration Valve Control 4.3.2. Span Calibration Summary Page 4.4 Integrated Multi-Point Calibration Adjustment 4.4.1. Multi-Point Calibration Valve Control 4.4.2 Multi-Point Calibration Summary 4.5 Coefficient Storage 4.6 Line Pressure Precautions Chapter 5 Service 5.1 Maintenance Page 5.1.1 Common Maintenance 5.1.2 Module Disassembly 5.1.3 Electronic Circuit Board Replacement Page Page Page 5.1.4 Replacement of Transducers 5.1.5 Calibration Valve Solenoid Replacement 5.1.6 Replacement of O-Rings Page Page Page Page Page 5.2 Upgrading Module Firmware 5.2.1 Upgrading Firmware Via Host TCP/IP Port 6.1.1 Checking Module Power-Up Sequence 6.1.2 Checking Module TCP/IP Communications Page Page 6.2 Zero and Gain Calibration Troubleshooting The Re-Zero calibration command (Calculate & Set Offsets) will automatically shift 6.3 User Software Chapter 7 Start-up Software 7.1 Introduction Appendix A All Commands Quick Reference Appendix B Model 9116 Response Error Codes Appendix C Cable Diagrams Page Page Appendix E Model 9116 Range Codes Page Appendix F NetScanner System Products Appendix G Binary Bit Map