Mounting and Module Dimensions | Measurement Specialties 9116

Pressure Systems, Inc.	Model 9116 User’s Manual

2.3.3Mounting and Module Dimensions

See the Model 9116 Data Sheet for exact dimensions of the module. A detailed mechanical drawing is also included in Appendix E.

2.3.4Network Communications Hookup

Every NetScanner™ System Intelligent Pressure Scanner contains a Host Port, allowing it to be interconnected in a network with other modules and a host computer. Model 9116 has an Ethernet Host Port using TCP/IP and UDP/IP transmission protocols.

2.3.4.1Ethernet Host Port Hookup

The Ethernet Host port of every Model 9116 Intelligent Pressure Scanner module, and its host computer, may be interconnected in a “star” network via a standard 10BaseT or 100BaseT, half or full duplex hub or switch. These standard devices will have their own power requirements.

Hubs will treat the host computer connection and all NetScanner™ System module connections alike. Switches may provide, or negotiate different speeds and/or different handshaking on its various ports. The Model 9116 will auto-negotiate through the hub or with the switch, for a half or full duplex connection at 10BaseT or 100BaseT speeds, establishing the best connection available. Ethernet communications pin assignments for the Model 9116 electrical connector are shown in Figure 2.2. See Figure 2.3 for typical network topology.

Figure 2.2

Ethernet Host Port Connector Pins

Page 9

www.PressureSystems.com

Image 18

Measurement Specialties 9116 Mounting and Module Dimensions, Network Communications Hookup, Ethernet Host Port Hookup

Contents

Model Intelligent Pressure Scanner User’s Manual Revision Revision History Print Date Table of Contents Table of Contents Service 102 Calibration Troubleshooting Guide 118 Start-up Software 124Appendices Preface Our Company Our WarrantyMerchandise Return Procedures Technical Support Website and E-Mail Our Firmware Our Publication Disclaimer Chapter General Information Introduction Description of the Instrument Model 9116 Intelligent Pressure Scanner Differences Between Models 9016 Set Hardware Trigger Mode w320x Set Module type alias w3200 Pressure Ranges Firmware Updates/Boot LoaderOptions Manifolds and Pressure Connections Communication Interfaces Preparation for Use Chapter Installation and Set Up Unpacking and InspectionSafety Considerations Environment Power Power Pin Assignments Network Communications Hookup Mounting and Module DimensionsEthernet Host Port Connector Pins Ethernet Host Port Hookup Pressure Systems, Inc Model 9116 User’s Manual Pressure Systems, Inc Model 9116 User’s Manual Ethernet Network Topology Diagnostic Port Hookup Pressure Connections Pressure Systems, Inc Model 9116 User’s Manual CAL Mode Inputs Purge Mode Inputs Leak Mode Inputs Supply Air Trigger Input Signal Power Up Checks and Self-DiagnosticsCase Grounding Chapter Programming and Operation Commands & Responses Introduction1.1 TCP/UDP/IP Protocols Commands General Command Format Command Field Position Field Datum Fields Format Field Responses An Acknowledge with Data response, or Interpreting Gain Values Span Calibration Adjustment Functional Command OverviewInterpreting Offset Values Re-zero Calibration Adjustment Interpreting Engineering Units Output Startup Initialization Module Data Acquisition Pressure Systems, Inc Model 9116 User’s Manual Delivery of Acquired Data To Host Network Query and Control Functions Other Functions Detailed Command Description Reference Type Command ID Command Functions Response Power UP Clear Command ‘A’Command Example Reset Command ‘B’ CONFIGURE/CONTROL MULTI-POINT Calibration Command ‘C’ Command Ii dddd ‘ 00’ is the sub-command index ii for Configure & Start Pppp npts ord avg 00 F 3 1 32 Read response a Pnt pppp.pppp Response Pppp.pppp pppp.pppp 01 1 -2.5 C 01 2 0.0 C 01 3 ‘ 02’ is the sub-command index ii for Calculate & Apply Example ‘ 03’ is the sub-command index ii for Abort Response Description Read Transducer Voltages Command ‘V’Vppppf Dddd.. dddd V11110 Calculate and SET Gains Command ‘Z’ ZppppResponse g.gggg .. g.gggg Z00F8 000212 1.000269 1.000437 1.000145 Read Transducer A/D Counts Command ‘a’ Appppf A11110 32767.000000 -32700.000000 10.000000 Read HIGH-SPEED Data Command ‘b’ Aaaabbbbcccc..rrrrAaaabbbbcccc .. rrrr Autonomous DEFINE/CONTROL Autonomous Host Streams Command ‘c’Ii dddd Command Packet Pressure Systems, Inc Model 9116 User’s Manual St pppp sync per f num ‘sync’ Meaning of ‘per’ Pressure Systems, Inc Model 9116 User’s Manual 00 1 000F 0 1 7 0 c 00 2 00F0 0 2 7 0 c 00 3 FF00 0 4 7 Command ‘c’- Sub-command Index 01 Start Streams Command 01 st Example Command ‘c’- Sub-command Index 02 Stop Streams Command 02 st Command ‘c’- Sub-command Index 03 Clear Streams Command 03 st02 0 c 03 3 c 01 Command ‘c’ Sub-command Index 04 Return Stream Information Command 04 stSt pppp sync per f num pro remport ipaddr bbbb Ffff 0 20 7 32000 1 7002 Command ‘c’ Sub-command Index 05 Select Data in a Stream St bbbb Bbbb hex 05 1 0012 Read response ‘ 06’ is the sub-command index ii for Select Protocol St pro remport ipaddr 06 0 1 7500 Read response 06 0 0 Read response Calculate and SET Offsets Command ‘h’ HppppGggg .. g.gggg HF000 0010 0.0020 0.0015 Read Temperature Counts Command ‘m’ Mppppf M11110 20692.000000 19783.000000 19204.000000 Read Temperature Voltages Command ‘n’ Nppppf N11110 53013 0.541698 0.503633 Read Module Status Command ‘q’ Returned value ‘w’ set Digit hex or other decimal IndexFirmware Version, as hex value Auto UDP Broadcast@Reset, as hex state Hardware trigger modeTemperature Range, as a hex value Q07 Read HIGH-PRECISION Data Command ‘r’ Rppppf R11110 Read Transducer Temperature Command ‘t’ TppppfResponse Dddd.. dddd T11110 Read Internal Coefficients Command ‘u’ Ufaacc-ccConverts each internal value from Max. char Dynamic EU Conversion coefficient c1 Span Cal Adjustment gain termDynamic EU Conversion coefficient c0 Dynamic EU Conversion coefficient c2 EU Pressure Conversion scaler default=1.0 Transducer Coefficients Description Datum TypeOther Coefficients Description Datum Type Example Download Internal Coefficients Command ‘v’ Vfaacc-ccdddd..ddddConverts each internal value from Other Coefficients Description Datum Type V00800-01 0.000 1.000 Response returned is a V01101 6.894757 Response returned is a Disable Automatic Shifting of Calibration Valve in ‘h’ SET/DO Operating OPTIONS/FUNCTIONS Command ‘w’Calculate and Set Offsets ‘h’ command default Wiidd eeee Set Cal Valves to RUN or CAL/RE-ZERO Position default Disable periodic Thermal Coefficient Update taskSet Number of A/D Samples to Average, default = Enable Host Response/Stream Back-Off Delay specified Description ‘q’ read Index Position W1200W0C01 Network Query UDP/IP Command ‘psi9000’ Parameter Meaning Psi9000 RE-BOOT Module UDP/IP Command ‘psireboot’ Command Psireboot ethadrPsireboot 00-E0-8D-00-00-01 Response None Command Psirarp ethadr Psirarp 00-E0-8D-00-00-01 Response None Chapter Calibration Introduction PTV Figures 4.1 Pneumatic Diagrams of the Calibration Manifold Re-zero Calibration Re-zero Calibration Valve Control Re-zero Calibration Summary Description Model 9116 CommandSpan Calibration Section Span Calibration Valve Control Span Calibration Summary Zffff Description Model 9116 Command Integrated Multi-Point Calibration Adjustment Multi-Point Calibration Valve Control Description Model Command Multi-Point Calibration Summary Coefficient Storage Line Pressure Precautions Chapter Service Maintenance Exploded View of Model Pressure Systems, Inc Model 9116 User’s Manual Common Maintenance Component Cross Reference Section Module Disassembly Electronic Circuit Board Replacement 3.2 PC-322/323 Main Board/PowerPC Daughter Board Assembly 3.1 PC-327 Analog Board PC-322/323 Assembly Remove and Replace PC-323 Daughter board on PC-322 Main PCB PC-323 Daughter Board Removed froom PC-322 Replacement of Transducers PC-322 BoardTop View of DH200 Calibration Valve Solenoid Replacement Replacement of O-Rings Solenoids in Module 6.1 DH200 Pressure Transducer O-Ring Replacement DH200 Transducer O-Ring Replacement Tubing Plate O-Ring Replacement Adapter Plate O-Ring Replacement Calibration Manifold Piston O-Ring Replacement Solenoid Valve O-Ring Replacement Upgrading Module Firmware Upgrading Firmware Via Host TCP/IP Port Checking Module Power-Up Sequence Checking Module TCP/IP Communications Module IP Address Assignment Pressure Systems, Inc Model 9116 User’s Manual Verifying Host TCP/IP Communications Zero and Gain Calibration Troubleshooting User Software Chapter Start-up Software Introduction Appendix a All Commands Quick Reference UDP/IP Appendix B Model 9116 Response Error Codes Undefined Command Received Appendix C Cable Diagrams Pressure Systems, Inc Model 9116 User’s Manual Appendix D Mounting Dimensions Appendix E Model 9116 Range Codes Psi 10 Water Column Psig Psi 20 Water Column Psid Psia Psid Psig Psia Appendix F NetScanner System ProductsModel Purpose Appendix G Binary Bit Map Bit Value If Set Position Binary Number Headquarters/Factory