Manuals / Measurement Specialties / Computer Equipment / Scanner

Measurement Specialties 9116 user manual Ffff 0 20 7 32000 1 7002

Models: 9116

1 143

Download 143 pages 39.58 Kb

Page 66

Pressure Systems, Inc.	Model 9116 User’s Manual

Example:

●Return configuration information for stream l

“c 04 1”

Read response:

“1 FFFF 0 20 7 32000 1 7002 200.200.200.1”

The above example shows all 16 (sixteen) channels. Data is acquired using hardware trigger with one (1) data packet acquired for every trigger events. Data is returned in format 7. (In the above example, 32000 packets have been returned so far.) Data is sent using UDP protocol to port 7002 at IP address 200.200.200.1. Pressure EU data only is returned for the requested channels.

Page 57

www.PressureSystems.com

Image 66

Measurement Specialties 9116 user manual Ffff 0 20 7 32000 1 7002

Contents

Model Intelligent Pressure Scanner User’s Manual Revision Revision History Print Date Table of Contents Table of Contents Service 102 CalibrationTroubleshooting Guide 118 Start-up Software 124Appendices Preface Our Company Our WarrantyMerchandise Return Procedures Technical SupportWebsite and E-Mail Our Firmware Our Publication Disclaimer Chapter General Information Introduction Description of the Instrument Model 9116 Intelligent Pressure ScannerDifferences Between Models 9016 Set Hardware Trigger Mode w320x Set Module type alias w3200Pressure Ranges Firmware Updates/Boot LoaderOptions Manifolds and Pressure ConnectionsCommunication Interfaces Preparation for Use Chapter Installation and Set Up Unpacking and InspectionSafety Considerations EnvironmentPower Power Pin AssignmentsNetwork Communications Hookup Mounting and Module DimensionsEthernet Host Port Connector Pins Ethernet Host Port HookupPressure Systems, Inc Model 9116 User’s Manual Pressure Systems, Inc Model 9116 User’s Manual Ethernet Network Topology Diagnostic Port Hookup Pressure ConnectionsPressure Systems, Inc Model 9116 User’s Manual CAL Mode Inputs Purge Mode InputsLeak Mode Inputs Supply AirTrigger Input Signal Power Up Checks and Self-DiagnosticsCase Grounding Chapter Programming and Operation Commands & Responses Introduction1.1 TCP/UDP/IP Protocols Commands General Command FormatCommand Field Position FieldDatum Fields Format FieldResponses An Acknowledge with Data response, orInterpreting Gain Values Span Calibration Adjustment Functional Command OverviewInterpreting Offset Values Re-zero Calibration Adjustment Interpreting Engineering Units OutputStartup Initialization Module Data AcquisitionPressure Systems, Inc Model 9116 User’s Manual Delivery of Acquired Data To Host Network Query and Control Functions Other FunctionsDetailed Command Description Reference Type Command ID Command FunctionsResponse Power UP Clear Command ‘A’Command ExampleReset Command ‘B’ CONFIGURE/CONTROL MULTI-POINT Calibration Command ‘C’ Command Ii dddd‘ 00’ is the sub-command index ii for Configure & Start Pppp npts ord avg00 F 3 1 32 Read response a Pnt pppp.pppp Response Pppp.pppp pppp.pppp01 1 -2.5 C 01 2 0.0 C 01 3 ‘ 02’ is the sub-command index ii for Calculate & Apply Example ‘ 03’ is the sub-command index ii for Abort Response Description Read Transducer Voltages Command ‘V’Vppppf Dddd.. ddddV11110 Calculate and SET Gains Command ‘Z’ ZppppResponse g.gggg .. g.gggg Z00F8 000212 1.000269 1.000437 1.000145Read Transducer A/D Counts Command ‘a’ AppppfA11110 32767.000000 -32700.000000 10.000000Read HIGH-SPEED Data Command ‘b’ Aaaabbbbcccc..rrrrAaaabbbbcccc .. rrrr Autonomous DEFINE/CONTROL Autonomous Host Streams Command ‘c’Ii dddd Command PacketPressure Systems, Inc Model 9116 User’s Manual St pppp sync per f num ‘sync’ Meaning of ‘per’ Pressure Systems, Inc Model 9116 User’s Manual 00 1 000F 0 1 7 0 c 00 2 00F0 0 2 7 0 c 00 3 FF00 0 4 7 Command ‘c’- Sub-command Index 01 Start Streams Command 01 stExample Command ‘c’- Sub-command Index 02 Stop Streams Command 02 stCommand ‘c’- Sub-command Index 03 Clear Streams Command 03 st02 0 c 03 3 c 01 Command ‘c’ Sub-command Index 04 Return Stream Information Command 04 stSt pppp sync per f num pro remport ipaddr bbbb Ffff 0 20 7 32000 1 7002 Command ‘c’ Sub-command Index 05 Select Data in a Stream St bbbbBbbb hex 05 1 0012 Read response ‘ 06’ is the sub-command index ii for Select Protocol St pro remport ipaddr06 0 1 7500 Read response 06 0 0 Read responseCalculate and SET Offsets Command ‘h’ HppppGggg .. g.gggg HF000 0010 0.0020 0.0015Read Temperature Counts Command ‘m’ MppppfM11110 20692.000000 19783.000000 19204.000000Read Temperature Voltages Command ‘n’ NppppfN11110 53013 0.541698 0.503633Read Module Status Command ‘q’ Returned value ‘w’ set Digit hex or other decimal IndexFirmware Version, as hex value Auto UDP Broadcast@Reset, as hex state Hardware trigger modeTemperature Range, as a hex value Q07 Read HIGH-PRECISION Data Command ‘r’ RppppfR11110 Read Transducer Temperature Command ‘t’ TppppfResponse Dddd.. dddd T11110 Read Internal Coefficients Command ‘u’ Ufaacc-ccConverts each internal value from Max. char Dynamic EU Conversion coefficient c1 Span Cal Adjustment gain termDynamic EU Conversion coefficient c0 Dynamic EU Conversion coefficient c2EU Pressure Conversion scaler default=1.0 Transducer Coefficients Description Datum TypeOther Coefficients Description Datum Type Example Download Internal Coefficients Command ‘v’ Vfaacc-ccdddd..ddddConverts each internal value from Other Coefficients Description Datum TypeV00800-01 0.000 1.000 Response returned is a V01101 6.894757 Response returned is aDisable Automatic Shifting of Calibration Valve in ‘h’ SET/DO Operating OPTIONS/FUNCTIONS Command ‘w’Calculate and Set Offsets ‘h’ command default Wiidd eeeeSet Cal Valves to RUN or CAL/RE-ZERO Position default Disable periodic Thermal Coefficient Update taskSet Number of A/D Samples to Average, default = Enable Host Response/Stream Back-Off Delay specifiedDescription ‘q’ read Index Position W1200W0C01 Network Query UDP/IP Command ‘psi9000’ Parameter MeaningPsi9000 RE-BOOT Module UDP/IP Command ‘psireboot’ Command Psireboot ethadrPsireboot 00-E0-8D-00-00-01 Response None Command Psirarp ethadr Psirarp 00-E0-8D-00-00-01 Response NoneChapter Calibration Introduction PTVFigures 4.1 Pneumatic Diagrams of the Calibration Manifold Re-zero Calibration Re-zero Calibration Valve ControlRe-zero Calibration Summary Description Model 9116 CommandSpan Calibration SectionSpan Calibration Valve Control Span Calibration Summary ZffffDescription Model 9116 Command Integrated Multi-Point Calibration Adjustment Multi-Point Calibration Valve ControlDescription Model Command Multi-Point Calibration SummaryCoefficient Storage Line Pressure Precautions Chapter Service Maintenance Exploded View of ModelPressure Systems, Inc Model 9116 User’s Manual Common Maintenance Component Cross Reference SectionModule Disassembly Electronic Circuit Board Replacement3.2 PC-322/323 Main Board/PowerPC Daughter Board Assembly 3.1 PC-327 Analog BoardPC-322/323 Assembly Remove and Replace PC-323 Daughter board on PC-322 Main PCB PC-323 Daughter Board Removed froom PC-322Replacement of Transducers PC-322 BoardTop View of DH200 Calibration Valve Solenoid Replacement Replacement of O-Rings Solenoids in Module6.1 DH200 Pressure Transducer O-Ring Replacement DH200 Transducer O-Ring ReplacementTubing Plate O-Ring Replacement Adapter Plate O-Ring Replacement Calibration Manifold Piston O-Ring Replacement Solenoid Valve O-Ring Replacement Upgrading Module Firmware Upgrading Firmware Via Host TCP/IP PortChecking Module Power-Up Sequence Checking Module TCP/IP Communications Module IP Address AssignmentPressure Systems, Inc Model 9116 User’s Manual Verifying Host TCP/IP Communications Zero and Gain Calibration Troubleshooting User Software Chapter Start-up Software Introduction Appendix a All Commands Quick Reference UDP/IPAppendix B Model 9116 Response Error Codes Undefined Command ReceivedAppendix C Cable Diagrams Pressure Systems, Inc Model 9116 User’s Manual Appendix D Mounting Dimensions Appendix E Model 9116 Range Codes Psi 10 Water Column Psig Psi 20 Water Column Psid PsiaPsid Psig Psia Appendix F NetScanner System ProductsModel Purpose Appendix G Binary Bit Map Bit Value If Set Position Binary NumberHeadquarters/Factory