Measurement Specialties 9116 ,

Pressure Systems, Inc. Model 9116 User’s Manual

Page 66 www.PressureSystems.com

Example:

● Send TCP/IP command to Model 9116 module (via its connected socket) that

returns decimal raw “temperature” A/D counts data for channels 1, 5, 9, and 13:

“ m11110”

Response contains data for channels 13, 9, 5, and 1 (left to right):

“ 20692.000000 19783.000000 19204.000000 20432.000000”

Contents

Main Page Table of Contents Page Page Page Preface Our Company Our Warranty Technical Support Merchandise Return Procedures Website and E-Mail Our Firmware Our Publication Disclaimer Chapter 1 General Information 1.1 Introduction 1.2 Description of the Instrument 1.2.1 Differences Between Models 9016 and 9116 Page 1.3 Options 1.3.1 Pressure Ranges 1.3.2 Manifolds and Pressure Connections 1.3.3 Communication Interfaces 2.2 Safety Considerations 2.3 Preparation for Use 2.3.1 Environment 2.3.2 Power 2.3.3 Mounting and Module Dimensions 2.3.4 Network Communications Hookup Page Note Page 2.3.5 Diagnostic Port Hookup 2.3.6 Pressure Connections Page Page Page 2.3.7 Case Grounding 2.3.8 Trigger Input Signal 2.3.9 Power Up Checks and Self-Diagnostics Chapter 3 Programming and Operation 3.1 Commands & Responses 3.1.1 Introduction 3.1.2 Commands Page Page 3.1.3 Responses 3.1.4 Functional Command Overview Page Page Page Page 3.2 Detailed Command Description Reference POWER UP CLEAR (Command A) RESET (Command B) CONFIGURE/CONTROL MULTI-POINT CALIBRATION (Command C) Command C Sub-command Index 00: Configure & Start Multi-Point Calibration Command C Sub-command Index 01: Collect Data for a Calibration Point Supply each of the previously-specified three (3) pressure calibration points to the Multi- Command C- Sub-command Index 02: Calculate & Apply Correction Coefficients Page Command C Sub-command Index 03: Abort Multi-Point Calibration READ TRANSDUCER VOLTAGES (Command V) Page CALCULATE AND SET GAINS (Command Z) Page READ TRANSDUCER A/D COUNTS (Command a) Page Page DEFINE/CONTROL AUTONOMOUS HOST STREAMS (Command c) Page Command c Sub-command Index 00: Configure A Host Delivery Stream Page Page Configure three (3) separate autonomous host delivery streams, and divide the modules Command c Sub-command Index 01: Start Stream(s) Command c Sub-command Index 02: Stop Stream(s) Command c Sub-command Index 03: Clear Stream(s) Stop all the streams configured previously. Then clear (un-define) only stream 3. Command c Sub-command Index 04: Return Stream Information Return configuration information for stream l Command c Sub-command Index 05: Select Data in a Stream Page Command c Sub-command Index 06: Select Protocol For Stream Delivery Configure all streams to be delivered via UDP/IP protocol. Host expects the UDP CALCULATE AND SET OFFSETS (Command h) READ TEMPERATURE COUNTS (Command m) READ TEMPERATURE VOLTAGES (Command n) READ MODULE STATUS (Command q) hhhh is a 4-digit hex datum (or other (**) decimal datum Page READ HIGH-PRECISION DATA (Command r) READ TRANSDUCER TEMPERATURE (Command t) READ INTERNAL COEFFICIENTS (Command u) Page Page DOWNLOAD INTERNAL COEFFICIENTS (Command v) Page Send TCP/IP command to module (i.e., via its connected socket): with SET/DO OPERATING OPTIONS/FUNCTIONS (Command w) Page Page NETWORK QUERY (UDP/IP Command psi9000) Query all module(s) on the network. RE-BOOT MODULE (UDP/IP Command psireboot) CHANGE MODULES IP ADDRESS RESOLUTION METHOD & RE-BOOT (UDP/IP Command psirarp) Chapter 4 Calibration 4.1 Introduction Page 4.2 Re-zero Calibration 4.2.1. Re-zero Calibration Valve Control 4.2.2 Re-zero Calibration Summary 4.3 Span Calibration 4.3.1. Span Calibration Valve Control 4.3.2. Span Calibration Summary Page 4.4 Integrated Multi-Point Calibration Adjustment 4.4.1. Multi-Point Calibration Valve Control 4.4.2 Multi-Point Calibration Summary 4.5 Coefficient Storage 4.6 Line Pressure Precautions Chapter 5 Service 5.1 Maintenance Page 5.1.1 Common Maintenance 5.1.2 Module Disassembly 5.1.3 Electronic Circuit Board Replacement Page Page Page 5.1.4 Replacement of Transducers 5.1.5 Calibration Valve Solenoid Replacement 5.1.6 Replacement of O-Rings Page Page Page Page Page 5.2 Upgrading Module Firmware 5.2.1 Upgrading Firmware Via Host TCP/IP Port 6.1.1 Checking Module Power-Up Sequence 6.1.2 Checking Module TCP/IP Communications Page Page 6.2 Zero and Gain Calibration Troubleshooting The Re-Zero calibration command (Calculate & Set Offsets) will automatically shift 6.3 User Software Chapter 7 Start-up Software 7.1 Introduction Appendix A All Commands Quick Reference Appendix B Model 9116 Response Error Codes Appendix C Cable Diagrams Page Page Appendix E Model 9116 Range Codes Page Appendix F NetScanner System Products Appendix G Binary Bit Map