Adapter Plate O-Ring Replacement | Measurement Specialties 9116

Pressure Systems, Inc.	Model 9116 User’s Manual

5.1.6.3Adapter Plate O-Ring Replacement

Following is a step-by-step procedure to replace Adapter plate O-rings in a Model 9116 Intelligent Pressure Scanner. The adapter plate is located opposite of the tubing plate on the calibration manifold. All DH200 transducers are attached to the adapter plate.

(1)Disassemble the module as described in Section 5.1.2.

(2)Remove the PC-327 Analog board as described in Section 5.1.3.1. Lay the circuit board to the side on an anti-static surface.

(3)Remove the six (6) 3/32" Allen-head screws that secure the adapter plate to the calibration valve housing. To remove the two (2) center screws, you must remove the DH200 transducers near the screws. Make sure to note the DH200 serial number and location. The plate should be gently lifted from the calibration housing.

(4)Carefully rotate or slide the adapter plate back and forth, pivoting on the guiding pin about 1/8" several times. This is done to loosen the O-rings from the calibration manifold. Lift the adapter plate straight up. Do not touch the calibration manifold.

(5)Remove and replace the O-rings needing maintenance using the procedure described in Section 5.1.6.1. Note that the O-ring seals use an additional Teflon cup seal placed on top of the O-ring. These Teflon seals do not require Krytox® grease.

(6)Examine the adapter plate and calibration valve surface to verify that no contaminants are on either surface. This generally requires microscopic examination. Replace the adapter plate by slowly placing the plate on the calibration manifold. Make sure that the O-ring is down towards the pneumatic sliding manifold and the guiding pin on the adapter plate fits into the mating hole of the calibration valve housing. Fasten the adapter plate evenly on all sides.

(7)Install the DH200 transducers that were previously removed. It is suggested to install them back in their original location.

(8)Replace the PC-327 Analog board as described in Section 5.1.3.1 and reassemble the module.

(9)Test your scanner to ensure proper operation.

Page 114

www.PressureSystems.com

Image 123

Measurement Specialties 9116 user manual Adapter Plate O-Ring Replacement

Contents

Model Intelligent Pressure Scanner User’s Manual Revision Revision History Print Date Table of Contents Table of Contents Calibration Service 102 Troubleshooting Guide 118 Start-up Software 124Appendices Preface Technical Support Our WarrantyMerchandise Return Procedures Our Company Website and E-Mail Our Firmware Our Publication Disclaimer Chapter General Information Introduction Model 9116 Intelligent Pressure Scanner Description of the Instrument Differences Between Models 9016 Set Module type alias w3200 Set Hardware Trigger Mode w320x Manifolds and Pressure Connections Firmware Updates/Boot LoaderOptions Pressure Ranges Communication Interfaces Environment Chapter Installation and Set Up Unpacking and InspectionSafety Considerations Preparation for Use Power Pin Assignments Power Ethernet Host Port Hookup Mounting and Module DimensionsEthernet Host Port Connector Pins Network Communications Hookup Pressure Systems, Inc Model 9116 User’s Manual Pressure Systems, Inc Model 9116 User’s Manual Ethernet Network Topology Pressure Connections Diagnostic Port Hookup Pressure Systems, Inc Model 9116 User’s Manual Purge Mode Inputs CAL Mode Inputs Supply Air Leak Mode Inputs Trigger Input Signal Power Up Checks and Self-DiagnosticsCase Grounding Chapter Programming and Operation Commands & Responses Introduction1.1 TCP/UDP/IP Protocols General Command Format Commands Position Field Command Field Format Field Datum Fields An Acknowledge with Data response, or Responses Interpreting Engineering Units Output Functional Command OverviewInterpreting Offset Values Re-zero Calibration Adjustment Interpreting Gain Values Span Calibration Adjustment Module Data Acquisition Startup Initialization Pressure Systems, Inc Model 9116 User’s Manual Delivery of Acquired Data To Host Other Functions Network Query and Control Functions Type Command ID Command Functions Detailed Command Description Reference Example Power UP Clear Command ‘A’Command Response Reset Command ‘B’ Command Ii dddd CONFIGURE/CONTROL MULTI-POINT Calibration Command ‘C’ Pppp npts ord avg ‘ 00’ is the sub-command index ii for Configure & Start 00 F 3 1 32 Read response a Response Pppp.pppp pppp.pppp Pnt pppp.pppp 01 1 -2.5 C 01 2 0.0 C 01 3 ‘ 02’ is the sub-command index ii for Calculate & Apply Example ‘ 03’ is the sub-command index ii for Abort Dddd.. dddd Read Transducer Voltages Command ‘V’Vppppf Response Description V11110 Calculate and SET Gains Command ‘Z’ ZppppResponse g.gggg .. g.gggg 000212 1.000269 1.000437 1.000145 Z00F8 Appppf Read Transducer A/D Counts Command ‘a’ 32767.000000 -32700.000000 10.000000 A11110 Read HIGH-SPEED Data Command ‘b’ Aaaabbbbcccc..rrrrAaaabbbbcccc .. rrrr Packet DEFINE/CONTROL Autonomous Host Streams Command ‘c’Ii dddd Command Autonomous Pressure Systems, Inc Model 9116 User’s Manual St pppp sync per f num ‘sync’ Meaning of ‘per’ Pressure Systems, Inc Model 9116 User’s Manual 00 1 000F 0 1 7 0 c 00 2 00F0 0 2 7 0 c 00 3 FF00 0 4 7 Command 01 st Command ‘c’- Sub-command Index 01 Start Streams Example Command 02 st Command ‘c’- Sub-command Index 02 Stop Streams Command ‘c’- Sub-command Index 03 Clear Streams Command 03 st02 0 c 03 3 c 01 Command ‘c’ Sub-command Index 04 Return Stream Information Command 04 stSt pppp sync per f num pro remport ipaddr bbbb Ffff 0 20 7 32000 1 7002 St bbbb Command ‘c’ Sub-command Index 05 Select Data in a Stream Bbbb hex 05 1 0012 Read response St pro remport ipaddr ‘ 06’ is the sub-command index ii for Select Protocol 06 0 0 Read response 06 0 1 7500 Read response Calculate and SET Offsets Command ‘h’ HppppGggg .. g.gggg 0010 0.0020 0.0015 HF000 Mppppf Read Temperature Counts Command ‘m’ 20692.000000 19783.000000 19204.000000 M11110 Nppppf Read Temperature Voltages Command ‘n’ 53013 0.541698 0.503633 N11110 Read Module Status Command ‘q’ Returned value ‘w’ set Digit hex or other decimal IndexFirmware Version, as hex value Auto UDP Broadcast@Reset, as hex state Hardware trigger modeTemperature Range, as a hex value Q07 Rppppf Read HIGH-PRECISION Data Command ‘r’ R11110 Read Transducer Temperature Command ‘t’ TppppfResponse Dddd.. dddd T11110 Read Internal Coefficients Command ‘u’ Ufaacc-ccConverts each internal value from Max. char Dynamic EU Conversion coefficient c2 Span Cal Adjustment gain termDynamic EU Conversion coefficient c0 Dynamic EU Conversion coefficient c1 EU Pressure Conversion scaler default=1.0 Transducer Coefficients Description Datum TypeOther Coefficients Description Datum Type Example Download Internal Coefficients Command ‘v’ Vfaacc-ccdddd..ddddConverts each internal value from Datum Type Other Coefficients Description V01101 6.894757 Response returned is a V00800-01 0.000 1.000 Response returned is a Wiidd eeee SET/DO Operating OPTIONS/FUNCTIONS Command ‘w’Calculate and Set Offsets ‘h’ command default Disable Automatic Shifting of Calibration Valve in ‘h’ Enable Host Response/Stream Back-Off Delay specified Disable periodic Thermal Coefficient Update taskSet Number of A/D Samples to Average, default = Set Cal Valves to RUN or CAL/RE-ZERO Position default Description ‘q’ read Index Position W1200W0C01 Parameter Meaning Network Query UDP/IP Command ‘psi9000’ Psi9000 RE-BOOT Module UDP/IP Command ‘psireboot’ Command Psireboot ethadrPsireboot 00-E0-8D-00-00-01 Response None Psirarp 00-E0-8D-00-00-01 Response None Command Psirarp ethadr PTV Chapter Calibration Introduction Figures 4.1 Pneumatic Diagrams of the Calibration Manifold Re-zero Calibration Valve Control Re-zero Calibration Section Description Model 9116 CommandSpan Calibration Re-zero Calibration Summary Span Calibration Valve Control Zffff Span Calibration Summary Description Model 9116 Command Multi-Point Calibration Valve Control Integrated Multi-Point Calibration Adjustment Multi-Point Calibration Summary Description Model Command Coefficient Storage Line Pressure Precautions Exploded View of Model Chapter Service Maintenance Pressure Systems, Inc Model 9116 User’s Manual Component Cross Reference Section Common Maintenance Electronic Circuit Board Replacement Module Disassembly 3.1 PC-327 Analog Board 3.2 PC-322/323 Main Board/PowerPC Daughter Board Assembly PC-322/323 Assembly PC-323 Daughter Board Removed froom PC-322 Remove and Replace PC-323 Daughter board on PC-322 Main PCB Replacement of Transducers PC-322 BoardTop View of DH200 Calibration Valve Solenoid Replacement Solenoids in Module Replacement of O-Rings DH200 Transducer O-Ring Replacement 6.1 DH200 Pressure Transducer O-Ring Replacement Tubing Plate O-Ring Replacement Adapter Plate O-Ring Replacement Calibration Manifold Piston O-Ring Replacement Solenoid Valve O-Ring Replacement Upgrading Firmware Via Host TCP/IP Port Upgrading Module Firmware Checking Module Power-Up Sequence Module IP Address Assignment Checking Module TCP/IP Communications Pressure Systems, Inc Model 9116 User’s Manual Verifying Host TCP/IP Communications Zero and Gain Calibration Troubleshooting User Software Chapter Start-up Software Introduction UDP/IP Appendix a All Commands Quick Reference Undefined Command Received Appendix B Model 9116 Response Error Codes Appendix C Cable Diagrams Pressure Systems, Inc Model 9116 User’s Manual Appendix D Mounting Dimensions Psi 10 Water Column Psig Psi 20 Water Column Psid Psia Appendix E Model 9116 Range Codes Psid Psig Psia Appendix F NetScanner System ProductsModel Purpose Bit Value If Set Position Binary Number Appendix G Binary Bit Map Headquarters/Factory