Multiquip SP706030, SP706020 SAW Lifting and Loading Safety, Transporting VIA TRUCK/TRAILER

Page 13

RULES AND REGULATIONS

SAW LIFTING AND LOADING SAFETY

CAUTION — Lifting Saw

This saw is very heavy. Use proper heavy lifting procedures and DO NOT attempt to lift by the guards.

DANGER — Do Not Stand Under Saw

NEVER stand under or allow anyone else to stand under the saw while it is being lifted.

DO NOT use the handle bars and/or front pointer as lifting points.

ALWAYS use ramps capable of supporting the weight of the saw and the operator to load and unload the saw.

NEVER tip the engine to extreme angles as it may cause oil to gravitate into the cylinder head making the engine start difficult.

TRANSPORTING (VIA TRUCK/TRAILER)

ALWAYS shutdown engine before transporting.

Tighten fuel tank cap securely and close fuel petcock to prevent fuel from spilling.

Drain fuel when transporting saw for long distances or over bad roads.

Use appropriate lifting equipment to ensure the safe movement of the saw.

When placing the saw on a truck-bed for transport, always tie-down the saw.

Do not use the handlebars or front pointer as tie-down points.

Never attempt to tow the saw untrailered behind a vehicle.

NEVER transport the saw to or from the job site with the blade mounted.

If the saw is being transported via a trailer, make sure the trailer complies with all local and state safety transportation laws.Refer to the following “Towing Safety Precautions” section for basic towing techniques.

TOWING SAFETY PRECAUTIONS (TRAILER USAGE)

CAUTION — Transporting Saw

Conform to Department ofTransportation (DOT) Safety Towing Regulations before transporting saw on public roads.

To reduce the possibility of an accident while transporting the saw on public roads, always make sure the trailer that supports the saw and the towing vehicle are in good operating condition and both units are mechanically sound.

The following list of suggestions should be used when towing your saw:

Check the tire air pressure on both towing vehicle and trailer. Refer to the tire manufacturer’s recommended pressure. Also check the tire tread wear on both vehicles.

Make sure the hitch and coupling of the towing vehicle are rated equal to or greater than the trailer “gross vehicle weight rating” (GVWR) of 6,000 lbs.

ALWAYS inspect the hitch and coupling for wear. NEVER tow a trailer with defective hitches, couplings, chains, etc.

ALWAYS make sure the trailer is equipped with Safety Chains and ensure they are attached properly.

ALWAYS make sure the vehicle and trailer directional, backup, brake, and trailer lights are connected and working.

DO NOT exceed the recommended highway speed when towing.

Use chock-blocks at each wheel when parked to prevent trailer from rolling.

Use the trailer’s swivel jack to adjust the trailer height to a level position while parked.

Avoid sudden stops and starts.This can cause the trailer to skid or jack-knife. Smooth, gradual starts and stops will improve towing.

Avoid sharp turns.

Trailer should be adjusted to a level position at all times when towing.

Raise and lock trailer wheel stand in the “UP” position when transporting.

DOT requirements include the following: Connect and test electric brake operation.

Secure portable power cables in cable tray with tie wraps.

SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Models Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningTable of Contents Page Training Checklist Training ChecklistRead Operator’s Manual completely Machine layout, location of components, checking of engineDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistHardware and damage check Safety Message Alert Symbols SafetyHazard Symbols Always wear approved respiratory protection when requiredSaw to be elevated Rotating blade can cut and crush. Keep hands and feet clearRules and Regulations General Safety Always keep the work area well-organized  Examine blade flanges for damage and excessive wear Diamond Blade SafetyTransporting VIA TRUCK/TRAILER SAW Lifting and Loading SafetyMaintenance Safety BatteryEmergencies See Figures 1 and 2 and for saw dimensions DimensionsOil bath design, fully enclosed housing SpecificationsBF3L2011 Engine SpecificationsHydro-gear hydrostatic transmission pump Lbs KgIntended USE / Familiarization FeaturesIntended USE EngineSerial TAG Serial TAG InformationSerial TAG is bonded to the inside of the console , Item Socket Connector Use to plug in optional light Controls and IndicatorsDepth Stop Allows repeatable cutting depths Components ComponentsFuel Filter Removes dirt and water from the engine fuel Basic Engine InformationLinked to the accelerator system Oil in crankcaseChoosing Proper Blade Size Choosing Proper Blade SizeEngine RPM and Surface Feet per Minute Sfpm Speeds Ratio Speeds and Blade Guard SizeSurface Feet per Minute Sfpm Data ~ No Load Blade RPM vs. Surface Feet Per Minute SfpmSpecifictoolsto be Used Specific Tools / SAW BladesSAW Blades Failure to thoroughly inspect the diamond blade FigureInstalling the Blade Installing the BladeAlign flange pin through the blade into the inner flange 12 In .48 cm Lbs 56.7-79.4 Kg Stacking Blades for Wide CutsBlade Guard Blade GuardsRemoving a Blade Guard To accomodate different cutting jobsInstalling the Flange Guard Installing a Blade GuardConnect the water delivery hose to the blade guard Figure Water Delivery System Water Delivery SystemsBattery Setup STAY-LEVEL HANDLEBARS/BATTERYTo adjust the handlebar height STAY-LEVEL Handlebars SLHFueling the SAW Fueling the SAWPriming the Fuel System Storage With Fuel In SystemPointer Adjustment Cold Weather OPERATION/POINTER AdjustmentColdweather Operation Block HeatersUntil readjusted Setting the Depth IndicatorRAISE-LOWER Controls Raise Lower ControlsBlade Shaft Rotation Disengagement System Blade Shaft Engage System / Wheel Drive SystemTo Stop blade shaft rotation To Start blade shaft rotationStarting and Stoppingthe Engine OperationStarting the Engine Allow the engine to warm up for several minutesRestarting After Running Out of Fuel Stopping the EngineOperating Synopsis Crank the engine normally until it startsLOADING, Unloading Andtransportingthe SAW Loading and TransportingMaintenance MaintenanceMaintenance Schedule AIR Cleaners DailyAir Cleaner Components Oil Filter 125 Hours Checking Engine OilChanging Engine Oil And Filter Oil And Fuel Lines Fuel Filter 500 HoursEngine Tune-Up LubricationCheck and clean battery terminals for corrosion BATTERY/CHARGING SystemCooling System Disconnect the air intake hose at the lifting bale , Item aRemovable Guards and Access Panels Replacing the BatteryRemove rear access panel Replace guards and panels prior to starting the engineBelt Tension Belts and PulleysAdjust to 3-1/2 notches on the tensioner Blade Shaft AssemblyRotary Belttensioner Blade ShaftDrive System Alignment Adjustment Removal and ReplacementBlade Alignment Drive System AlignmentRemoving the Inner Blade Flange Blade Flange REMOVAL/INSTALLATIONBlade Shaft Tolerance Inner Flange Inside Face Installing the Inner Blade FlangeCircuit Breakers and Starter Relays Maximum CUT Depth AdjustmentRAISE-LOWER System PTO Drive MaintenanceRaise-Lower System Troubleshooting Raise-Lower System TroubleshootingHydraulic System Maintenance R Control AdjustmentHydraulic Oil System Hydraulic System Drainingthe Hydraulic SystemStay-Level Handles SLH Tips When Draining and Filling the Hydraulic Oil SystemLongterm Storage Decommissioning SAW/COMPONENTSTroubleshooting Engine Battery and starter Loose, damaged wiring?Intake air restricted? NecessaryBlade Troubleshooting Troubleshooting BladePage Electrical Diagram UP to S/N AF3700155 Electrical Diagram to SN AF3700155Electrical Diagram S/N AF3700156 and UP Electrical Diagram SN AF3700156 & UPHydraulic Schematic to SN AF3700155 Hydraulic Schematic to SN AF3700155Hydraulic Schematic SN AF3700156 and UP Hydraulic Schematic SN AF3700156 & UPYour Local Dealer is HERE’S HOW to GET Help
Related manuals
Manual 82 pages 45.83 Kb

SP706016, SP706026, SP706030, SP706036, SP706020 specifications

Multiquip is a prominent name in the construction equipment industry, known for its innovative and reliable products. Among its versatile offerings, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 stand out as notable concrete pump models. These pumps provide exceptional performance and efficiency, making them ideal for a wide range of applications.

Each model in this lineup is engineered for maximum durability and reliability. The SP706020, for instance, features a powerful and efficient hydraulic system that allows for smooth operation and consistent performance, even in demanding conditions. It is designed with a robust frame that can withstand rigorous job site environments, ensuring longevity and reduced maintenance.

The SP706016 stands out with its compact design, making it suitable for smaller job sites while still offering high output and efficiency. This model is equipped with advanced safety features, such as emergency stop buttons and pressure relief valves, ensuring safe operation for the user and surrounding personnel.

Notably, the SP706036 is designed for high-capacity pumping. It is ideal for larger projects that require higher output without compromising on efficiency. Its advanced pumping technology reduces the potential for blockages, enhancing overall productivity. The SP706030 presents a balance between power and size, making it an excellent choice for medium-scale projects.

The SP706026 is notable for its energy-efficient design, which minimizes fuel consumption while providing robust performance. This model reflects Multiquip's commitment to sustainability and cost-effectiveness, allowing contractors to save on operational costs over time.

Across the series, user-friendly controls and adjustable settings provide operators with the flexibility needed to handle various types of concrete mixes and job specifications. Additionally, these models are fitted with high-quality components that enhance performance and reduce wear and tear.

In summary, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 are versatile concrete pumps equipped with cutting-edge technology, ensuring high efficiency, reliability, and safety on any job site. Their various features and specifications make them a valuable addition to any construction operation, catering to diverse project needs while ensuring exceptional performance.
Top Page Image Contents