Multiquip SP706030 SILICOSIS/RESPIRATORY Warnings Silicosis Warning, Respiratory Hazards

Page 3

SILICOSIS/RESPIRATORY WARNINGS

WARNING

SILICOSIS WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance known to cause cancer. When cutting such materials, always follow the respiratory precautions mentioned above.

WARNING

RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow the recommendations of the manufacturers or suppliers, OSHA/NIOSH, and occupational and trade associations. Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the materials being used.

SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Models Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningTable of Contents Page Machine layout, location of components, checking of engine Training ChecklistTraining Checklist Read Operator’s Manual completelyDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistHardware and damage check Always wear approved respiratory protection when required SafetySafety Message Alert Symbols Hazard SymbolsSaw to be elevated Rotating blade can cut and crush. Keep hands and feet clearRules and Regulations General Safety Always keep the work area well-organized  Examine blade flanges for damage and excessive wear Diamond Blade SafetyTransporting VIA TRUCK/TRAILER SAW Lifting and Loading SafetyBattery Maintenance SafetyEmergencies See Figures 1 and 2 and for saw dimensions DimensionsOil bath design, fully enclosed housing SpecificationsLbs Kg Engine SpecificationsBF3L2011 Hydro-gear hydrostatic transmission pumpEngine FeaturesIntended USE / Familiarization Intended USESerial TAG Information Serial TAGSerial TAG is bonded to the inside of the console , Item Controls and Indicators Socket Connector Use to plug in optional lightDepth Stop Allows repeatable cutting depths Components ComponentsOil in crankcase Basic Engine InformationFuel Filter Removes dirt and water from the engine fuel Linked to the accelerator systemRatio Speeds and Blade Guard Size Choosing Proper Blade SizeChoosing Proper Blade Size Engine RPM and Surface Feet per Minute Sfpm SpeedsSurface Feet per Minute Sfpm Data ~ No Load Blade RPM vs. Surface Feet Per Minute SfpmFailure to thoroughly inspect the diamond blade Figure Specific Tools / SAW BladesSpecifictoolsto be Used SAW BladesInstalling the Blade Installing the BladeAlign flange pin through the blade into the inner flange 12 In .48 cm Lbs 56.7-79.4 Kg Stacking Blades for Wide CutsTo accomodate different cutting jobs Blade GuardsBlade Guard Removing a Blade GuardInstalling a Blade Guard Installing the Flange GuardConnect the water delivery hose to the blade guard Figure Water Delivery System Water Delivery SystemsSTAY-LEVEL Handlebars SLH STAY-LEVEL HANDLEBARS/BATTERYBattery Setup To adjust the handlebar heightStorage With Fuel In System Fueling the SAWFueling the SAW Priming the Fuel SystemBlock Heaters Cold Weather OPERATION/POINTER AdjustmentPointer Adjustment Coldweather OperationRaise Lower Controls Setting the Depth IndicatorUntil readjusted RAISE-LOWER ControlsTo Start blade shaft rotation Blade Shaft Engage System / Wheel Drive SystemBlade Shaft Rotation Disengagement System To Stop blade shaft rotationAllow the engine to warm up for several minutes OperationStarting and Stoppingthe Engine Starting the EngineCrank the engine normally until it starts Stopping the EngineRestarting After Running Out of Fuel Operating SynopsisLOADING, Unloading Andtransportingthe SAW Loading and TransportingAIR Cleaners Daily MaintenanceMaintenance Maintenance ScheduleAir Cleaner Components Checking Engine Oil Oil Filter 125 HoursChanging Engine Oil And Filter Lubrication Fuel Filter 500 HoursOil And Fuel Lines Engine Tune-UpDisconnect the air intake hose at the lifting bale , Item a BATTERY/CHARGING SystemCheck and clean battery terminals for corrosion Cooling SystemReplace guards and panels prior to starting the engine Replacing the BatteryRemovable Guards and Access Panels Remove rear access panelBelt Tension Belts and PulleysBlade Shaft Blade Shaft AssemblyAdjust to 3-1/2 notches on the tensioner Rotary BelttensionerDrive System Alignment Removal and ReplacementDrive System Alignment Adjustment Blade AlignmentRemoving the Inner Blade Flange Blade Flange REMOVAL/INSTALLATIONBlade Shaft Tolerance Inner Flange Inside Face Installing the Inner Blade FlangeCircuit Breakers and Starter Relays Maximum CUT Depth AdjustmentRAISE-LOWER System PTO Drive MaintenanceRaise-Lower System Troubleshooting Raise-Lower System TroubleshootingR Control Adjustment Hydraulic System MaintenanceHydraulic Oil System Hydraulic System Drainingthe Hydraulic SystemDecommissioning SAW/COMPONENTS Tips When Draining and Filling the Hydraulic Oil SystemStay-Level Handles SLH Longterm StorageTroubleshooting Engine Necessary Loose, damaged wiring?Battery and starter Intake air restricted?Blade Troubleshooting Troubleshooting BladePage Electrical Diagram UP to S/N AF3700155 Electrical Diagram to SN AF3700155Electrical Diagram S/N AF3700156 and UP Electrical Diagram SN AF3700156 & UPHydraulic Schematic to SN AF3700155 Hydraulic Schematic to SN AF3700155Hydraulic Schematic SN AF3700156 and UP Hydraulic Schematic SN AF3700156 & UPYour Local Dealer is HERE’S HOW to GET Help
Related manuals
Manual 82 pages 45.83 Kb

SP706016, SP706026, SP706030, SP706036, SP706020 specifications

Multiquip is a prominent name in the construction equipment industry, known for its innovative and reliable products. Among its versatile offerings, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 stand out as notable concrete pump models. These pumps provide exceptional performance and efficiency, making them ideal for a wide range of applications.

Each model in this lineup is engineered for maximum durability and reliability. The SP706020, for instance, features a powerful and efficient hydraulic system that allows for smooth operation and consistent performance, even in demanding conditions. It is designed with a robust frame that can withstand rigorous job site environments, ensuring longevity and reduced maintenance.

The SP706016 stands out with its compact design, making it suitable for smaller job sites while still offering high output and efficiency. This model is equipped with advanced safety features, such as emergency stop buttons and pressure relief valves, ensuring safe operation for the user and surrounding personnel.

Notably, the SP706036 is designed for high-capacity pumping. It is ideal for larger projects that require higher output without compromising on efficiency. Its advanced pumping technology reduces the potential for blockages, enhancing overall productivity. The SP706030 presents a balance between power and size, making it an excellent choice for medium-scale projects.

The SP706026 is notable for its energy-efficient design, which minimizes fuel consumption while providing robust performance. This model reflects Multiquip's commitment to sustainability and cost-effectiveness, allowing contractors to save on operational costs over time.

Across the series, user-friendly controls and adjustable settings provide operators with the flexibility needed to handle various types of concrete mixes and job specifications. Additionally, these models are fitted with high-quality components that enhance performance and reduce wear and tear.

In summary, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 are versatile concrete pumps equipped with cutting-edge technology, ensuring high efficiency, reliability, and safety on any job site. Their various features and specifications make them a valuable addition to any construction operation, catering to diverse project needs while ensuring exceptional performance.
Top Page Image Contents