Multiquip SP706020, SP706016 Circuit Breakers and Starter Relays, Maximum CUT Depth Adjustment

Page 50

MAINTENANCE

CIRCUIT BREAKERS AND STARTER RELAYS

Thermalcircuitbreakersandglowplugstarterrelaysarelocated behind the console access cover at the top of the console. See Figure 59.

12

3

4

1.Circuit Breakers

2.Relay, Glow Plug

3.DelayTimer

4.Starter Relay

Figure 59. Circuit Breakers and Starter Relay

Under normal circumstances the circuit breakers do not require service.They automatically reset when an overload condition is corrected. If a breaker is cycling on and off, locate the cause of the electrical overload and repair as required.

MAXIMUM CUT DEPTH ADJUSTMENT

The saw comes factory-adjusted for maximum usable cut depth. Should this setting need to be changed, perform the following:

While adjustment of the depth stop limiting bolts can change the maximum usable cut depth, they should not be adjusted to compensate for unit “wobble” or blade/cut problems.These are a result of other issues that should be addressed.

1.With the BLADE REMOVED, park the saw on a flat and level surface.

2.Fully lower the saw onto the depth limiting stop bolts. See Figure 60.

3.Measurethedistancefromthebladeflangestothesurface.

4.If adjustment is required, loosen locknut on the right-side depth limiting stop bolt (Figure 60, item 2) and screw bolt

2

1

3

4

1.Left-Side Stop Bolt

2.Right-Side Stop Bolt

3.Blade Flanges

4.Blade Shaft Housing Figure 60. Depth Adjustment

in several turns until it no longer makes contact with the axle.

5.Adjust the left-side stop bolt (item 1) in or out until the blade flange or lower belt guard achieves 1/8" to 3/16" ground clearance.Tighten lock nut on left side.

6.Raise saw and place 2 jack stands under the blade shaft housing.

7.Whileholdingtheraise-lowerswitchintheloweringposition, raise the front axle assembly until it contacts the left-side depth limiting stop bolt.

8.While holding the axle firmly against the left-side depth limiting stop bolt, screw the right-side depth limiting stop bolt out until it makes contact with the axle. Tighten lock nut on right side.

Following this procedure will prevent torsional stresses being applied to the frame when fully lowered due to uneven adjustment of depth limiting stop bolts.

PAGE50 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)

Image 50
Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents Page Read Operator’s Manual completely Training ChecklistTraining Checklist Machine layout, location of components, checking of engineHardware and damage check Daily PRE-OPERATION ChecklistDaily PRE-OPERATION Checklist Hazard Symbols SafetySafety Message Alert Symbols Always wear approved respiratory protection when requiredRotating blade can cut and crush. Keep hands and feet clear Saw to be elevatedGeneral Safety Rules and Regulations Always keep the work area well-organized Diamond Blade Safety  Examine blade flanges for damage and excessive wearSAW Lifting and Loading Safety Transporting VIA TRUCK/TRAILEREmergencies BatteryMaintenance Safety Dimensions See Figures 1 and 2 and for saw dimensionsSpecifications Oil bath design, fully enclosed housingHydro-gear hydrostatic transmission pump Engine SpecificationsBF3L2011 Lbs KgIntended USE FeaturesIntended USE / Familiarization EngineSerial TAG is bonded to the inside of the console , Item Serial TAG InformationSerial TAG Depth Stop Allows repeatable cutting depths Controls and IndicatorsSocket Connector Use to plug in optional light Components ComponentsLinked to the accelerator system Basic Engine InformationFuel Filter Removes dirt and water from the engine fuel Oil in crankcaseEngine RPM and Surface Feet per Minute Sfpm Speeds Choosing Proper Blade SizeChoosing Proper Blade Size Ratio Speeds and Blade Guard SizeBlade RPM vs. Surface Feet Per Minute Sfpm Surface Feet per Minute Sfpm Data ~ No LoadSAW Blades Specific Tools / SAW BladesSpecifictoolsto be Used Failure to thoroughly inspect the diamond blade FigureAlign flange pin through the blade into the inner flange Installing the BladeInstalling the Blade Stacking Blades for Wide Cuts 12 In .48 cm Lbs 56.7-79.4 KgRemoving a Blade Guard Blade GuardsBlade Guard To accomodate different cutting jobsConnect the water delivery hose to the blade guard Figure Installing a Blade GuardInstalling the Flange Guard Water Delivery Systems Water Delivery SystemTo adjust the handlebar height STAY-LEVEL HANDLEBARS/BATTERYBattery Setup STAY-LEVEL Handlebars SLHPriming the Fuel System Fueling the SAWFueling the SAW Storage With Fuel In SystemColdweather Operation Cold Weather OPERATION/POINTER AdjustmentPointer Adjustment Block HeatersRAISE-LOWER Controls Setting the Depth IndicatorUntil readjusted Raise Lower ControlsTo Stop blade shaft rotation Blade Shaft Engage System / Wheel Drive SystemBlade Shaft Rotation Disengagement System To Start blade shaft rotationStarting the Engine OperationStarting and Stoppingthe Engine Allow the engine to warm up for several minutesOperating Synopsis Stopping the EngineRestarting After Running Out of Fuel Crank the engine normally until it startsLoading and Transporting LOADING, Unloading Andtransportingthe SAWMaintenance Schedule MaintenanceMaintenance AIR Cleaners DailyAir Cleaner Components Changing Engine Oil And Filter Checking Engine OilOil Filter 125 Hours Engine Tune-Up Fuel Filter 500 HoursOil And Fuel Lines LubricationCooling System BATTERY/CHARGING SystemCheck and clean battery terminals for corrosion Disconnect the air intake hose at the lifting bale , Item aRemove rear access panel Replacing the BatteryRemovable Guards and Access Panels Replace guards and panels prior to starting the engineBelts and Pulleys Belt TensionRotary Belttensioner Blade Shaft AssemblyAdjust to 3-1/2 notches on the tensioner Blade ShaftBlade Alignment Removal and ReplacementDrive System Alignment Adjustment Drive System AlignmentBlade Flange REMOVAL/INSTALLATION Removing the Inner Blade FlangeInstalling the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside FaceMaximum CUT Depth Adjustment Circuit Breakers and Starter RelaysPTO Drive Maintenance RAISE-LOWER SystemRaise-Lower System Troubleshooting Raise-Lower System TroubleshootingHydraulic Oil System R Control AdjustmentHydraulic System Maintenance Drainingthe Hydraulic System Hydraulic SystemLongterm Storage Tips When Draining and Filling the Hydraulic Oil SystemStay-Level Handles SLH Decommissioning SAW/COMPONENTSTroubleshooting Engine Intake air restricted? Loose, damaged wiring?Battery and starter NecessaryTroubleshooting Blade Blade TroubleshootingPage Electrical Diagram to SN AF3700155 Electrical Diagram UP to S/N AF3700155Electrical Diagram SN AF3700156 & UP Electrical Diagram S/N AF3700156 and UPHydraulic Schematic to SN AF3700155 Hydraulic Schematic to SN AF3700155Hydraulic Schematic SN AF3700156 & UP Hydraulic Schematic SN AF3700156 and UPHERE’S HOW to GET Help Your Local Dealer is
Related manuals
Manual 82 pages 45.83 Kb

SP706016, SP706026, SP706030, SP706036, SP706020 specifications

Multiquip is a prominent name in the construction equipment industry, known for its innovative and reliable products. Among its versatile offerings, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 stand out as notable concrete pump models. These pumps provide exceptional performance and efficiency, making them ideal for a wide range of applications.

Each model in this lineup is engineered for maximum durability and reliability. The SP706020, for instance, features a powerful and efficient hydraulic system that allows for smooth operation and consistent performance, even in demanding conditions. It is designed with a robust frame that can withstand rigorous job site environments, ensuring longevity and reduced maintenance.

The SP706016 stands out with its compact design, making it suitable for smaller job sites while still offering high output and efficiency. This model is equipped with advanced safety features, such as emergency stop buttons and pressure relief valves, ensuring safe operation for the user and surrounding personnel.

Notably, the SP706036 is designed for high-capacity pumping. It is ideal for larger projects that require higher output without compromising on efficiency. Its advanced pumping technology reduces the potential for blockages, enhancing overall productivity. The SP706030 presents a balance between power and size, making it an excellent choice for medium-scale projects.

The SP706026 is notable for its energy-efficient design, which minimizes fuel consumption while providing robust performance. This model reflects Multiquip's commitment to sustainability and cost-effectiveness, allowing contractors to save on operational costs over time.

Across the series, user-friendly controls and adjustable settings provide operators with the flexibility needed to handle various types of concrete mixes and job specifications. Additionally, these models are fitted with high-quality components that enhance performance and reduce wear and tear.

In summary, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 are versatile concrete pumps equipped with cutting-edge technology, ensuring high efficiency, reliability, and safety on any job site. Their various features and specifications make them a valuable addition to any construction operation, catering to diverse project needs while ensuring exceptional performance.