Multiquip SP706016, SP706020 Operation, Starting and Stoppingthe Engine, Starting the Engine

Page 36

OPERATION

STARTING AND STOPPINGTHE ENGINE

WARNING

DO NOT leave the saw unattended while the engine is running.NEVER start, park, or leave the saw unattended on a slope.

CAUTION

Allow the engine to warm up before increasing engine speed.

DO NOT stop the engine abruptly when hot.Reduce the throttle to idle and allow the engine to run one or two minutes before turning the ignition switch off.This allows the engine to cool down preventing damage to the turbo charger.

Starting the Engine

1.Move the speed control handle to the NEUTRAL position.

2. Set the throttle to IDLE.

3.Make sure the emergency stop button is in the OUT position.

4.Ensure that water lines are attached and water is flowing to the saw blade.

5.Turn the ignition switch to the ON position (Figure 32).

Figure 32. ON/OFF Switch

6.Wait for the glow plug indicator light to go out. See Figure 33.

7.Turn ignition switch to the START position; RELEASE switch after engine starts.

1.Engine oil pressure warning light

2.Engine high temp warning light

3.Glow plug warning light

4.Not used

5.Air filter warning light

6.Battery warning light

Figure 33. Ignition Switch and System Status

8.Allow the engine to warm up for several minutes.

9.Set the throttle to the recommended engine RPM to match the recommended blade speed of the attached blade.

10.Lower the blade to the cut depth.

11.Move the control handle FORWARD to advance the cut.

In case of an EMERGENCY, push the RED EMERGENCY-STOP BUTTON to stop all functions (Figure 34). Engine will not crank when emergency stop button is depressed.

Figure 34. Emergency Stop Button

PAGE36 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents Page Training Checklist Training ChecklistRead Operator’s Manual completely Machine layout, location of components, checking of engineDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistHardware and damage check Safety Safety Message Alert SymbolsHazard Symbols Always wear approved respiratory protection when requiredRotating blade can cut and crush. Keep hands and feet clear Saw to be elevatedGeneral Safety Rules and Regulations Always keep the work area well-organized Diamond Blade Safety  Examine blade flanges for damage and excessive wearSAW Lifting and Loading Safety Transporting VIA TRUCK/TRAILERBattery Maintenance SafetyEmergencies Dimensions See Figures 1 and 2 and for saw dimensionsSpecifications Oil bath design, fully enclosed housingEngine Specifications BF3L2011Hydro-gear hydrostatic transmission pump Lbs KgFeatures Intended USE / FamiliarizationIntended USE EngineSerial TAG Information Serial TAGSerial TAG is bonded to the inside of the console , Item Controls and Indicators Socket Connector Use to plug in optional lightDepth Stop Allows repeatable cutting depths Components ComponentsBasic Engine Information Fuel Filter Removes dirt and water from the engine fuelLinked to the accelerator system Oil in crankcaseChoosing Proper Blade Size Choosing Proper Blade SizeEngine RPM and Surface Feet per Minute Sfpm Speeds Ratio Speeds and Blade Guard SizeBlade RPM vs. Surface Feet Per Minute Sfpm Surface Feet per Minute Sfpm Data ~ No LoadSpecific Tools / SAW Blades Specifictoolsto be UsedSAW Blades Failure to thoroughly inspect the diamond blade FigureInstalling the Blade Installing the BladeAlign flange pin through the blade into the inner flange Stacking Blades for Wide Cuts 12 In .48 cm Lbs 56.7-79.4 KgBlade Guards Blade GuardRemoving a Blade Guard To accomodate different cutting jobsInstalling a Blade Guard Installing the Flange GuardConnect the water delivery hose to the blade guard Figure Water Delivery Systems Water Delivery SystemSTAY-LEVEL HANDLEBARS/BATTERY Battery SetupTo adjust the handlebar height STAY-LEVEL Handlebars SLHFueling the SAW Fueling the SAWPriming the Fuel System Storage With Fuel In SystemCold Weather OPERATION/POINTER Adjustment Pointer AdjustmentColdweather Operation Block HeatersSetting the Depth Indicator Until readjustedRAISE-LOWER Controls Raise Lower ControlsBlade Shaft Engage System / Wheel Drive System Blade Shaft Rotation Disengagement SystemTo Stop blade shaft rotation To Start blade shaft rotationOperation Starting and Stoppingthe EngineStarting the Engine Allow the engine to warm up for several minutesStopping the Engine Restarting After Running Out of FuelOperating Synopsis Crank the engine normally until it startsLoading and Transporting LOADING, Unloading Andtransportingthe SAWMaintenance MaintenanceMaintenance Schedule AIR Cleaners DailyAir Cleaner Components Checking Engine Oil Oil Filter 125 HoursChanging Engine Oil And Filter Fuel Filter 500 Hours Oil And Fuel LinesEngine Tune-Up LubricationBATTERY/CHARGING System Check and clean battery terminals for corrosionCooling System Disconnect the air intake hose at the lifting bale , Item aReplacing the Battery Removable Guards and Access PanelsRemove rear access panel Replace guards and panels prior to starting the engineBelts and Pulleys Belt TensionBlade Shaft Assembly Adjust to 3-1/2 notches on the tensionerRotary Belttensioner Blade ShaftRemoval and Replacement Drive System Alignment AdjustmentBlade Alignment Drive System AlignmentBlade Flange REMOVAL/INSTALLATION Removing the Inner Blade FlangeInstalling the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside FaceMaximum CUT Depth Adjustment Circuit Breakers and Starter RelaysPTO Drive Maintenance RAISE-LOWER SystemRaise-Lower System Troubleshooting Raise-Lower System TroubleshootingR Control Adjustment Hydraulic System MaintenanceHydraulic Oil System Drainingthe Hydraulic System Hydraulic SystemTips When Draining and Filling the Hydraulic Oil System Stay-Level Handles SLHLongterm Storage Decommissioning SAW/COMPONENTSTroubleshooting Engine Loose, damaged wiring? Battery and starterIntake air restricted? NecessaryTroubleshooting Blade Blade TroubleshootingPage Electrical Diagram to SN AF3700155 Electrical Diagram UP to S/N AF3700155Electrical Diagram SN AF3700156 & UP Electrical Diagram S/N AF3700156 and UPHydraulic Schematic to SN AF3700155 Hydraulic Schematic to SN AF3700155Hydraulic Schematic SN AF3700156 & UP Hydraulic Schematic SN AF3700156 and UPHERE’S HOW to GET Help Your Local Dealer is
Related manuals
Manual 82 pages 45.83 Kb

SP706016, SP706026, SP706030, SP706036, SP706020 specifications

Multiquip is a prominent name in the construction equipment industry, known for its innovative and reliable products. Among its versatile offerings, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 stand out as notable concrete pump models. These pumps provide exceptional performance and efficiency, making them ideal for a wide range of applications.

Each model in this lineup is engineered for maximum durability and reliability. The SP706020, for instance, features a powerful and efficient hydraulic system that allows for smooth operation and consistent performance, even in demanding conditions. It is designed with a robust frame that can withstand rigorous job site environments, ensuring longevity and reduced maintenance.

The SP706016 stands out with its compact design, making it suitable for smaller job sites while still offering high output and efficiency. This model is equipped with advanced safety features, such as emergency stop buttons and pressure relief valves, ensuring safe operation for the user and surrounding personnel.

Notably, the SP706036 is designed for high-capacity pumping. It is ideal for larger projects that require higher output without compromising on efficiency. Its advanced pumping technology reduces the potential for blockages, enhancing overall productivity. The SP706030 presents a balance between power and size, making it an excellent choice for medium-scale projects.

The SP706026 is notable for its energy-efficient design, which minimizes fuel consumption while providing robust performance. This model reflects Multiquip's commitment to sustainability and cost-effectiveness, allowing contractors to save on operational costs over time.

Across the series, user-friendly controls and adjustable settings provide operators with the flexibility needed to handle various types of concrete mixes and job specifications. Additionally, these models are fitted with high-quality components that enhance performance and reduce wear and tear.

In summary, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 are versatile concrete pumps equipped with cutting-edge technology, ensuring high efficiency, reliability, and safety on any job site. Their various features and specifications make them a valuable addition to any construction operation, catering to diverse project needs while ensuring exceptional performance.
Top Page Image Contents