Multiquip SP706016 Stay-Level Handlebars/Battery, STAY-LEVEL Handlebars SLH, Battery Setup

Page 31

STAY-LEVEL HANDLEBARS/BATTERY

STAY-LEVEL HANDLEBARS (SLH)

This saw incorporates a unique handlebar design that allows the handlebars to maintain a level height position regardless of the angle of the saw. Along with this, the height of the handlebars can be adjusted for individual operator providing for more comfortable operation.

To adjust the handlebar height:

1.Loosen the SLH linkage adjustment plate bolts (Figure 21).

2.Set the handlebars to the desired height.

3. Tighten the SLH linkage adjustment plate bolts.

Figure 21. Stay-Level Handlebars

BATTERY SETUP

WARNING — Battery hazards

Always recharge the battery in a well- ventilated area to avoid risk of a dangerous concentration of combustible gases.

Battery electrolyte contains corrosive, toxic chemical. (dilute sulfuric acid). Avoid contact with eyes and skin.

WARNING — Shock hazards

Disconnect battery cables before inspecting electrical system and never “spark” battery terminals to test for charge.

CAUTION — Battery safety

Use all safety precautions specified by the battery manufacturer when working with the battery.

This saw was shipped with a wet charged battery (Figure 22). This battery may need to be charged for a brief period of time as per the manufacturer instructions.

Figure 22. Battery and Battery Box

To install the battery on the saw, make sure that the battery is properly clamped into the battery box. Connect the positive cables to the positive terminals on the battery first, then connect the negative cables to the negative terminals.

The 7060 uses two positive battery cables and twonegativebatterycables.Onesetisforengine start, and the other is for the raise/lower pump assembly.Make sure that both sets of cables are connected to the battery.Also, LIMIT the cycling of the raise/lower system on battery power only. Frequentcyclingwilldiminishthelifeofthebattery.

SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Models Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningTable of Contents Page Machine layout, location of components, checking of engine Training ChecklistTraining Checklist Read Operator’s Manual completelyDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistHardware and damage check Always wear approved respiratory protection when required SafetySafety Message Alert Symbols Hazard SymbolsSaw to be elevated Rotating blade can cut and crush. Keep hands and feet clearRules and Regulations General Safety Always keep the work area well-organized  Examine blade flanges for damage and excessive wear Diamond Blade SafetyTransporting VIA TRUCK/TRAILER SAW Lifting and Loading SafetyMaintenance Safety BatteryEmergencies See Figures 1 and 2 and for saw dimensions DimensionsOil bath design, fully enclosed housing SpecificationsLbs Kg Engine SpecificationsBF3L2011 Hydro-gear hydrostatic transmission pumpEngine FeaturesIntended USE / Familiarization Intended USESerial TAG Serial TAG InformationSerial TAG is bonded to the inside of the console , Item Socket Connector Use to plug in optional light Controls and IndicatorsDepth Stop Allows repeatable cutting depths Components ComponentsOil in crankcase Basic Engine InformationFuel Filter Removes dirt and water from the engine fuel Linked to the accelerator systemRatio Speeds and Blade Guard Size Choosing Proper Blade SizeChoosing Proper Blade Size Engine RPM and Surface Feet per Minute Sfpm SpeedsSurface Feet per Minute Sfpm Data ~ No Load Blade RPM vs. Surface Feet Per Minute SfpmFailure to thoroughly inspect the diamond blade Figure Specific Tools / SAW BladesSpecifictoolsto be Used SAW BladesInstalling the Blade Installing the BladeAlign flange pin through the blade into the inner flange 12 In .48 cm Lbs 56.7-79.4 Kg Stacking Blades for Wide CutsTo accomodate different cutting jobs Blade GuardsBlade Guard Removing a Blade GuardInstalling the Flange Guard Installing a Blade GuardConnect the water delivery hose to the blade guard Figure Water Delivery System Water Delivery SystemsSTAY-LEVEL Handlebars SLH STAY-LEVEL HANDLEBARS/BATTERYBattery Setup To adjust the handlebar heightStorage With Fuel In System Fueling the SAWFueling the SAW Priming the Fuel SystemBlock Heaters Cold Weather OPERATION/POINTER AdjustmentPointer Adjustment Coldweather OperationRaise Lower Controls Setting the Depth IndicatorUntil readjusted RAISE-LOWER ControlsTo Start blade shaft rotation Blade Shaft Engage System / Wheel Drive SystemBlade Shaft Rotation Disengagement System To Stop blade shaft rotationAllow the engine to warm up for several minutes OperationStarting and Stoppingthe Engine Starting the EngineCrank the engine normally until it starts Stopping the EngineRestarting After Running Out of Fuel Operating SynopsisLOADING, Unloading Andtransportingthe SAW Loading and TransportingAIR Cleaners Daily MaintenanceMaintenance Maintenance ScheduleAir Cleaner Components Oil Filter 125 Hours Checking Engine OilChanging Engine Oil And Filter Lubrication Fuel Filter 500 HoursOil And Fuel Lines Engine Tune-UpDisconnect the air intake hose at the lifting bale , Item a BATTERY/CHARGING SystemCheck and clean battery terminals for corrosion Cooling SystemReplace guards and panels prior to starting the engine Replacing the BatteryRemovable Guards and Access Panels Remove rear access panelBelt Tension Belts and PulleysBlade Shaft Blade Shaft AssemblyAdjust to 3-1/2 notches on the tensioner Rotary BelttensionerDrive System Alignment Removal and ReplacementDrive System Alignment Adjustment Blade AlignmentRemoving the Inner Blade Flange Blade Flange REMOVAL/INSTALLATIONBlade Shaft Tolerance Inner Flange Inside Face Installing the Inner Blade FlangeCircuit Breakers and Starter Relays Maximum CUT Depth AdjustmentRAISE-LOWER System PTO Drive MaintenanceRaise-Lower System Troubleshooting Raise-Lower System TroubleshootingHydraulic System Maintenance R Control AdjustmentHydraulic Oil System Hydraulic System Drainingthe Hydraulic SystemDecommissioning SAW/COMPONENTS Tips When Draining and Filling the Hydraulic Oil SystemStay-Level Handles SLH Longterm StorageTroubleshooting Engine Necessary Loose, damaged wiring?Battery and starter Intake air restricted?Blade Troubleshooting Troubleshooting BladePage Electrical Diagram UP to S/N AF3700155 Electrical Diagram to SN AF3700155Electrical Diagram S/N AF3700156 and UP Electrical Diagram SN AF3700156 & UPHydraulic Schematic to SN AF3700155 Hydraulic Schematic to SN AF3700155Hydraulic Schematic SN AF3700156 and UP Hydraulic Schematic SN AF3700156 & UPYour Local Dealer is HERE’S HOW to GET Help
Related manuals
Manual 82 pages 45.83 Kb

SP706016, SP706026, SP706030, SP706036, SP706020 specifications

Multiquip is a prominent name in the construction equipment industry, known for its innovative and reliable products. Among its versatile offerings, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 stand out as notable concrete pump models. These pumps provide exceptional performance and efficiency, making them ideal for a wide range of applications.

Each model in this lineup is engineered for maximum durability and reliability. The SP706020, for instance, features a powerful and efficient hydraulic system that allows for smooth operation and consistent performance, even in demanding conditions. It is designed with a robust frame that can withstand rigorous job site environments, ensuring longevity and reduced maintenance.

The SP706016 stands out with its compact design, making it suitable for smaller job sites while still offering high output and efficiency. This model is equipped with advanced safety features, such as emergency stop buttons and pressure relief valves, ensuring safe operation for the user and surrounding personnel.

Notably, the SP706036 is designed for high-capacity pumping. It is ideal for larger projects that require higher output without compromising on efficiency. Its advanced pumping technology reduces the potential for blockages, enhancing overall productivity. The SP706030 presents a balance between power and size, making it an excellent choice for medium-scale projects.

The SP706026 is notable for its energy-efficient design, which minimizes fuel consumption while providing robust performance. This model reflects Multiquip's commitment to sustainability and cost-effectiveness, allowing contractors to save on operational costs over time.

Across the series, user-friendly controls and adjustable settings provide operators with the flexibility needed to handle various types of concrete mixes and job specifications. Additionally, these models are fitted with high-quality components that enhance performance and reduce wear and tear.

In summary, the Multiquip SP706020, SP706016, SP706036, SP706030, and SP706026 are versatile concrete pumps equipped with cutting-edge technology, ensuring high efficiency, reliability, and safety on any job site. Their various features and specifications make them a valuable addition to any construction operation, catering to diverse project needs while ensuring exceptional performance.
Top Page Image Contents