Multiquip MLT25 TIRe saFeTY Unsafe Tires, Lug nuts or Wheels, Determining Load Limit of Trailer

Page 36

safety guidelines — TRAILERS

TIRe saFeTY

unsafe Tires, Lug nuts or Wheels

Trailer tires and wheels are more likely to fail than car tires and wheels because they carry a heavier load. Therefore, it is essential to inspect the trailer tires before each tow.

If a tire has a bald spot, bulge, cuts, is showing any cords, or is cracked, replace the tire before towing. If a tire has uneven tread wear, take the trailer to a dealer service center for diagnosis.

Uneven tread wear can be caused by tire imbalance, axle misalignment or incorrect infl ation.

Tires with too little tread will not provide adequate tracking on wet roadways and can result in loss of control, leading to death or serious injury.

Improper tire pressure causes an unstable trailer and can result in a tire blowout and loss of control. Therefore, before each tow you must also check the tire pressure.Tire pressure must be checked when tires are cold.

Allow 3 hours cool-down after driving as much as 1 mile at 40 mph before checking tire pressure. Trailer tires will be infl ated to higher pressures than passenger vehicle tires.

Since trailer wheels and lug nuts (or bolts) are subjected to greater side loads than automobile wheels, they are more prone to loosen. Before each tow, check to make sure they are tight.

The proper tightness (torque) for lug nuts is listed in the lug nut tightening section of this manual. Use a torque wrench to tighten the lug nuts. If you do not have a torque wrench, use a lug wrench (from your tow vehicle) and tighten the nuts as much as you can. Then have a service garage or trailer dealer tighten the lug nuts to the proper torque.

WaRnIng

Metal creep between the wheel rim and lug nuts will cause rim to loosen and could result in a wheel coming off, leading to death or serious injury.

Tighten lug nuts before each tow.

Lug nuts are also prone to loosen after first being assembled. When driving a new trailer (or after wheels have been remounted), check to make sure they are tight after the fi rst 10, 25 and 50 miles of driving and before each tow thereafter.

Failure to perform this check can result in a wheel parting from the trailer and a crash, leading to death or serious injury.

WaRnIng

Lug nuts are prone to loosen after initial installation, which can lead to death or serious injury.

Check lug nuts for tightness on a new trailer or when wheel(s) have been remounted after the fi rst 10, 25 and 50 miles of driving.

WaRnIng

Improper lug nut torque can cause a wheel parting from the trailer, leading to death or serious injury.

Be sure lug nuts are tight before each tow.

WaRnIng

Improper tire pressure can result in a blowout and loss of control, which can lead to death or serious injury.

Be sure tires are infl ated to pressure indicated on side wall before towing trailer.

Determining Load Limit of Trailer

Determining the load limits of a trailer includes more than understanding the load limits of the tires alone. On all trailers there is a Federal certifi cation/VIN label that is located on the forward half of the left (road) side of the unit. This certifi cation/VIN label will indicate the trailer’s Gross Vehicle Weight Rating (GVWR). This is the most weight the fully loaded trailer can weigh. It will also provide the Gross Axle Weight Rating (GAWR). This is the most a the axle can weigh.

page 36 — MLT25 sERIES LIGHT TOWER • operation manual — rev. #0 (11/28/12)

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Model MLT25 sERIES Proposition 65 warning Reporting Safety Defects NhtsaTable of Contents Specifications are subject to change without noticeSafety Information SaFeTY MessagesSaFeTY sYMBOLs Addresses practices not related to personal injuryGeneRaL saFeTY LIgHT TOWeR saFeTY LaMp saFeTYTOWIng saFeTY TRanspORTIng saFeTY Loading and Tie-Down on Flatbed TruckELeCTRICaL saFeTY „ neveR operate light towerMLT25 Series Specifications Light Tower SpecificationsTrailer Specifications Generator/Engine SpecificationsDimensions DimensionsReference Letter Description Dimension Length Mast Stowed Position Length Mast Deployed PositionGeneral information Metal Halide LampsComponents Major Components Control Panel SideCircuit Breakers, 3-Pole, 15 a Turn the lamps on and off Major Components Front/RearRead all safety instructions at the beginning of manual InspectionBefore starting Check all fastening nuts and bolts for tightnessContact between the two connectors Female and Male ConnectorOperation Starting the EngineMast operation Outriggers and Support StandsRaising the Mast Raising the Mast Lowering the MastStowing the Mast to Horizontal Position Rotating the MastMove the Voltage Selector to the desired position Voltage Selector PositionsMaintenance Generator/ENGINE MaintenanceCheck Cable Wear Servicing the Mast Raise/Lower Cable SystemServicing the Mast Extension Cable System Lower the mast to the horizontal resting positionMaintenance Trailers Manually Adjusting the BrakesTrailer Brakes Hydraulic BrakesAdjustable Channel Hydraulic Brake TroubleshootingWheel Hub Adjustment Leaf SuspensionSafety guidelines Trailers COMMOn Causes for LOss of TRaILeRTRaILeR TOWIng guIDeLInes DRIvIng COnDITIOns COupLIng to THe TOW veHICLeInOpeRaBLe BRaKes, LIgHTs or MIRRORs TRaILeR TOWIng TIpsTRaILeR vIn Tag ELeCTRICaL COnneCTOR TOW veHICLeSuspensIOn sYsTeM BRaKe COnTROLLeRSaFeTY CHaIns TRaILeR LIgHTIng anD BRaKIng COnneCTORBReaKaWaY sYsTeM JaCKsTanDLock washer and hitch frame Trailer tongue. Wood or concrete blocks may also be usedCoupling the Trailer to the Tow vehicle Ball Coupler Attaching safety Chain Breakaway Brake systemBreakaway Cable surge Brake system Connecting Trailer Lights Uncoupling the Ball HitchPInTLe Hitch COupLeR Pintle Coupler and pintle HookFigure H. Attaching Safety Chain Pintle Hitch Coupling Trailer to Tow vehicle pintle CouplerTIRe saFeTY Unsafe Tires, Lug nuts or Wheels Determining Load Limit of TrailerBe sure lug nuts are tight before each tow Step Determining Load Limit of Tow vehicle stepTIRe FunDaMenTaLs Table a. speed RatingLetter Rating Speed Rating Tire safety Tips Tire RepairReplacing Worn or Damaged Tires Uniform Tire Quality grading standards uTQgsTable B. Tire Wear Troubleshooting Wheel RimsWheels, Bearings and Lug nuts Lug nut Torque RequirementsLights and signals Table C. Tire Torque RequirementsLamp Troubleshooting Symptom Possible Cause SolutionWhen switch is first Checking voltage and ballast Turned on Replacement minimizes color differencesClean fixture Lamp starts slowly ARC does not strike Defective Lamp?Lamp Troubleshooting Guide ConnectionsBallast Removal StartingElectronic components locator Wiring diagram sheet L3 NEU. GNDTB1 E1 AWG Page HERE’S HOW to GET Help
Top Page Image Contents