Multiquip MLT25 operation manual Lights and signals, Table C. Tire Torque Requirements

Page 41

safety guidelines — TRAILERS

Table C. Tire Torque Requirements

Wheel size

First pass

second pass

Third pass

FT-LBs

FT-LBs

FT-LBs

 

 

 

 

 

12"

20-25

35-40

50-65

 

 

 

 

13"

20-25

35-40

50-65

 

 

 

 

14"

20-25

50-60

90-120

15"

20-25

50-60

90-120

16"

20-25

50-60

90-120

Lights and signals

Before each tow, check the trailer taillights, stoplights, turn signals and any clearance lights for proper operation.

Replace any broken or burned-out lamps as necessary. Check the wire harness for cuts, fraying or other damage. If it needs replacing, contact your dealer.

WaRnIng

Improper operating taillights, stoplights and turn signals can cause collisions.

Check all lights before each tow.

Figure M. Trailer to Tow Vehicle Wiring Diagram

MLT25 SERIES LIGHT TOWER • operation manual — rev. #0 (11/28/12) — page 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Model MLT25 sERIES Proposition 65 warning Nhtsa Reporting Safety DefectsSpecifications are subject to change without notice Table of ContentsSaFeTY Messages Safety InformationSaFeTY sYMBOLs Addresses practices not related to personal injuryGeneRaL saFeTY LaMp saFeTY LIgHT TOWeR saFeTYTOWIng saFeTY Loading and Tie-Down on Flatbed Truck TRanspORTIng saFeTY„ neveR operate light tower ELeCTRICaL saFeTYLight Tower Specifications MLT25 Series SpecificationsTrailer Specifications Generator/Engine SpecificationsDimensions DimensionsReference Letter Description Dimension Length Mast Stowed Position Length Mast Deployed PositionMetal Halide Lamps General informationMajor Components Control Panel Side ComponentsMajor Components Front/Rear Circuit Breakers, 3-Pole, 15 a Turn the lamps on and offInspection Read all safety instructions at the beginning of manualBefore starting Check all fastening nuts and bolts for tightnessFemale and Male Connector Contact between the two connectorsStarting the Engine OperationMast operation Outriggers and Support StandsRaising the Mast Lowering the Mast Raising the MastStowing the Mast to Horizontal Position Rotating the MastVoltage Selector Positions Move the Voltage Selector to the desired positionGenerator/ENGINE Maintenance MaintenanceCheck Cable Wear Servicing the Mast Raise/Lower Cable SystemLower the mast to the horizontal resting position Servicing the Mast Extension Cable SystemManually Adjusting the Brakes Maintenance TrailersTrailer Brakes Hydraulic BrakesHydraulic Brake Troubleshooting Adjustable ChannelLeaf Suspension Wheel Hub AdjustmentTRaILeR TOWIng guIDeLInes Safety guidelines TrailersCOMMOn Causes for LOss of TRaILeR COupLIng to THe TOW veHICLe DRIvIng COnDITIOnsTRaILeR vIn Tag InOpeRaBLe BRaKes, LIgHTs or MIRRORsTRaILeR TOWIng TIps TOW veHICLe ELeCTRICaL COnneCTORSuspensIOn sYsTeM BRaKe COnTROLLeRTRaILeR LIgHTIng anD BRaKIng COnneCTOR SaFeTY CHaInsBReaKaWaY sYsTeM JaCKsTanDCoupling the Trailer to the Tow vehicle Ball Coupler Lock washer and hitch frameTrailer tongue. Wood or concrete blocks may also be used Breakaway Cable surge Brake system Attaching safety ChainBreakaway Brake system Uncoupling the Ball Hitch Connecting Trailer LightsPInTLe Hitch COupLeR Pintle Coupler and pintle HookCoupling Trailer to Tow vehicle pintle Coupler Figure H. Attaching Safety Chain Pintle HitchBe sure lug nuts are tight before each tow TIRe saFeTY Unsafe Tires, Lug nuts or WheelsDetermining Load Limit of Trailer Determining Load Limit of Tow vehicle step StepLetter Rating Speed Rating TIRe FunDaMenTaLsTable a. speed Rating Tire Repair Tire safety TipsReplacing Worn or Damaged Tires Uniform Tire Quality grading standards uTQgsWheel Rims Table B. Tire Wear TroubleshootingWheels, Bearings and Lug nuts Lug nut Torque RequirementsTable C. Tire Torque Requirements Lights and signalsSymptom Possible Cause Solution Lamp TroubleshootingReplacement minimizes color differences When switch is first Checking voltage and ballast Turned onClean fixture Lamp starts slowly ARC does not strike Defective Lamp?Connections Lamp Troubleshooting GuideBallast Removal StartingElectronic components locator L3 NEU. GND Wiring diagram sheetTB1 E1 AWG Page HERE’S HOW to GET Help
Top Page Image Contents