Multiquip MLT25 operation manual Circuit Breakers, 3-Pole, 15 a Turn the lamps on and off

Page 15

components

21

21

 

20

23

REAR VIEW

22

FRONT VIEW

24

Figure 3. Major Components (Front/Rear)

13.Tongue Jackstand — Use this jackstand to support the tongue when attaching the light tower to a towing vehicle.

14.Safety Chain — Always attach safety chain to the towing vehicle. Never tow the light tower with the safety chain unattached.

15.Ball Hitch Coupler — Attach this coupler to the towing vehicle. Use only the specified ball diameter as indicated on your coupler. Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure.

16.Vertical Mast Winch — Use this winch to raise the mast to the vertical position.

17.Mast Lock/Release Pin — Pull this pin to start placing the tower mast in the vertical position. When tower mast has reached full vertical position, insert pin to keep mast from falling.

18.Tie-Down Points — Used to tie down light tower with strap or chains to allow even application of force to the front and rear of the equipment during transport.

19.Fuse Block Assembly — Contains the fuses that protect the lamp circuit breakers.

20.License Light — This light illuminates the license plate. Whenever towing of the light tower is required, make sure this light is operational.

21.Brake Lights — Before towing the light tower, make sure that these lights are operational and are working correctly. Never tow the light tower if these lights are inoperative.

22.Engine Exhaust Pipe — Directs engine exhaust to the rear of the light tower. NEVER block this exhaust pipe with obstructions. ALWAYS place the generator in an area free of obstructions.

23.Tires — This light tower uses ST205/75D15 LR-C size tire. Replace with only recommended tire size. Never tow light tower with bad or worn tires.

24.Circuit Breakers, 3-Pole, 15 A — Turn the lamps on and off.

MLT25 SERIES LIGHT TOWER • operation manual — rev. #0 (11/28/12) — page 15

Image 15
Contents Model MLT25 sERIES Proposition 65 warning Nhtsa Reporting Safety DefectsSpecifications are subject to change without notice Table of ContentsAddresses practices not related to personal injury Safety InformationSaFeTY Messages SaFeTY sYMBOLsGeneRaL saFeTY LaMp saFeTY LIgHT TOWeR saFeTYTOWIng saFeTY Loading and Tie-Down on Flatbed Truck TRanspORTIng saFeTY„ neveR operate light tower ELeCTRICaL saFeTYGenerator/Engine Specifications MLT25 Series SpecificationsLight Tower Specifications Trailer SpecificationsLength Mast Stowed Position Length Mast Deployed Position DimensionsDimensions Reference Letter Description DimensionMetal Halide Lamps General informationMajor Components Control Panel Side ComponentsMajor Components Front/Rear Circuit Breakers, 3-Pole, 15 a Turn the lamps on and offCheck all fastening nuts and bolts for tightness Read all safety instructions at the beginning of manualInspection Before startingFemale and Male Connector Contact between the two connectorsOutriggers and Support Stands OperationStarting the Engine Mast operationRaising the Mast Rotating the Mast Raising the MastLowering the Mast Stowing the Mast to Horizontal PositionVoltage Selector Positions Move the Voltage Selector to the desired positionServicing the Mast Raise/Lower Cable System MaintenanceGenerator/ENGINE Maintenance Check Cable WearLower the mast to the horizontal resting position Servicing the Mast Extension Cable SystemHydraulic Brakes Maintenance TrailersManually Adjusting the Brakes Trailer BrakesHydraulic Brake Troubleshooting Adjustable ChannelLeaf Suspension Wheel Hub AdjustmentSafety guidelines Trailers COMMOn Causes for LOss of TRaILeRTRaILeR TOWIng guIDeLInes COupLIng to THe TOW veHICLe DRIvIng COnDITIOnsInOpeRaBLe BRaKes, LIgHTs or MIRRORs TRaILeR TOWIng TIpsTRaILeR vIn Tag BRaKe COnTROLLeR ELeCTRICaL COnneCTORTOW veHICLe SuspensIOn sYsTeMJaCKsTanD SaFeTY CHaInsTRaILeR LIgHTIng anD BRaKIng COnneCTOR BReaKaWaY sYsTeMLock washer and hitch frame Trailer tongue. Wood or concrete blocks may also be usedCoupling the Trailer to the Tow vehicle Ball Coupler Attaching safety Chain Breakaway Brake systemBreakaway Cable surge Brake system Pintle Coupler and pintle Hook Connecting Trailer LightsUncoupling the Ball Hitch PInTLe Hitch COupLeRCoupling Trailer to Tow vehicle pintle Coupler Figure H. Attaching Safety Chain Pintle HitchTIRe saFeTY Unsafe Tires, Lug nuts or Wheels Determining Load Limit of TrailerBe sure lug nuts are tight before each tow Determining Load Limit of Tow vehicle step StepTIRe FunDaMenTaLs Table a. speed RatingLetter Rating Speed Rating Uniform Tire Quality grading standards uTQgs Tire safety TipsTire Repair Replacing Worn or Damaged TiresLug nut Torque Requirements Table B. Tire Wear TroubleshootingWheel Rims Wheels, Bearings and Lug nutsTable C. Tire Torque Requirements Lights and signalsSymptom Possible Cause Solution Lamp TroubleshootingLamp starts slowly ARC does not strike Defective Lamp? When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Clean fixtureStarting Lamp Troubleshooting GuideConnections Ballast RemovalElectronic components locator L3 NEU. GND Wiring diagram sheetTB1 E1 AWG Page HERE’S HOW to GET Help