Multiquip R2000H manual Free Wheel Engagement Pin, Tie-Down Transport Points

Page 19

1. Engine – The MQ R2000H ride-on roller uses an 7.1 HP Honda GX240K1QAE2 air cooled, 4-stroke, single cylinder gasoline engine.This engine uses unleaded gasoline.

2.SteeringWheel — Use this wheel to steer the roller.

3.Parking Break Lever — Pull the lever upward to set the parking break. To release the parking break, press and hold the button on top of the lever and push lever downward.

4.Transmission Control Lever — Push the lever forward to make the roller travel in a forward direction, pull the lever backward to make the roller travel in a reverse direction. Maximum travel speed is 5.6 MPH (9.0 KPH). Center position is neutral, no travel.

5.Documentation Box — Maintain and store at all times Operation, Parts, and Engine manuals in this box.

6.Operator's Seat — A contoured seat that provides visibility of both front rear drum edges during operation. NEVER! start the roller unless seated in the operator's seat.

7.Water Tank/Cap — Remove filler cap and fill with clean fresh water.Water tank capacity is 21 gallons (79.5 liters). If water level is low, add water as necessary.

8.Rear Lifting Point – Attach a crane or suitable lifting device to this point when lifting of the roller is required.

9.Rear Scrapper – This adjustable rear scrapper blade helps prevent the buildup of material between the drum and frame.

10.Rear Roller – This roller is a 32-inch wide steel drum with beveled edges (no vibration). The beveled edges help prevent asphalt marring.

11.Front Lifting Point – Attach a crane or suitable lifting device to this point when lifting of the roller is required.

12.Front Scrapper – This adjustable rear scrapper blade helps prevent the buildup of material between the drum and frame.

13.Front Roller Water Plug – Remove this plug to add water (ballast) to the front drum. This plug is located on each side of the split front roller.

14.Front Roller Zerk Fitting – Grease this fitting as recommended in the maintenance section of this manual.

15.Steering Zerk Fitting – Grease this fitting as recommended in the maintenance section of this manual.

R2000H — ROLLER COMPONENTS

16.Access Panel – Lift this -panel to gain access to the transmission assembly and battery.

A.Transmission – This roller uses a hydrostatic pump which provides hydraulic pressure to the hydraulic drive system. Fill the pump reservoir with hydrostatic transmission fluid. Fill with Mobil 300, GM Dextron B or Ford MCZ-41A type transmission fluid.

Free Wheel Engagement Pin

The hydrostatic transmission is equipped with a free wheel engagement pin, which, when actuated, allows the oil to circulate freely within the roller, thereby permitting the roller to be moved without the engine running. This engagement pin is only to be used in the event the roller is disabled.

This pin is located on the side of the hydrostatic transmission underneath the acess cover.It is actuated by pushing the pin inward and placing the locking clip over the pin to keep it in place.

B.Battery – Provides +12VDC to the electrical system. Replace only with recommended type battery, see specification Table 1.

17.Sprinkler Valve Lever – A gravity feed spray bar is provided on the front and rear of the roller for the wetting of the roll for asphalt pavement. Pull upward on the lever to start the flow of water to the gravity feed system. Push the lever downward to stop the flow of water.

18.Front Roller – This roller is a split 28-inch wide steel drum with beveled edges (no vibration). The beveled edges help prevent asphalt marring.

19.Rear Roller Water Plug – Remove this plug to add water (ballast) to the rear drum. This plug is located on the chain-side of the roller. It is shown here for clarity only.

Tie-Down Transport Points –

Attach a chain or suitable tie-down

NOTE device to these points when transporting of the roller is required.

R2000H RIDE-ON STATIC ROLLER — OPERATION AND PARTS MANUAL — REV. #6 (11/29/10) — PAGE 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model R2000H Proposition 65WARNING Page Table of Contents Ordering parts has never been easier Parts Ordering Procedures25 x 7 x 7 in .5 x17.8 x17.8 cm LH 9 in mmRH 3.25 in mm LH 1.75 in mm Drive to rear rollR2000H Specifications Engine R2000H Roller Dimensions R2000H DimensionsSeriously injured if you do not follow directions Injury to yourself and othersInstructions Always wear approved respiratory protectionRules for Safe Operation Always wear seat belts Rules for Safe OperationEmergencies Never stand below roller when it is being liftedMachine Safety Decals Operation and Safety DecalsRecommended Slope Do not operate this roller on slippery or wet surfacesTipping Rollover Tipping RolloversPage Roller Components R2000H Roller ComponentsTie-Down Transport Points Free Wheel Engagement PinAttach a chain or suitable tie-down R2000H Engine Components Capacity is 400 cc Reference manufacturer engine R2000H InspectionBefore Starting Engine Oil CheckWater System Check Place the Choke Lever in the Closed position Sit down in the operators seatStarting the Engine R2000H Operation Ignition SwitchPlace the transmission lever in the neutral position Water Sprinklers ControlEmergency Shut-Down Lubrication R2000H MaintenanceHydrostatic Transmission Drive Chains Transmission Control Lever AdjustmentSteering Adjustment Drive Chains Tension AdjustmentUse a belt tension tester to check the belt tension TransmissionV-Belt AdjustmentScrapers, Cocoa Mats, and Sprinkler Bars Roller Storage R2000H Preparation for Long -TERM StorageR2000H Troubleshooting Roller Engine Troubleshooting R2000H Troubleshooting EngineXxxxx only Not Used on Explanation of Code in Remarks ColumnR2000H Suggested Spare Parts Name Plate and Decals R2000H Name Plate and DecalsDECAL, MQ Multiquip DECAL, MQ R2000H LeftDECAL, MQ R2000H Right DECAL, MQBrake Assy R2000H Brake AssySpacer Adjustable YokeLEVER, Parking Brake CAP Screw 5/16Steering Assy R2000H Steering AssyWasher 5/8 CAPHexnut 5/8 Flatwasher 5/8Chassis & Covers Assy R2000H Chassis and Covers AssyPLATE, Shifter Main Body FrameGUARD, Rear PANEL, Left SideBattery Assy R2000H Battery AssyRED BatteryCLAMP, Battery CAP Screw 3/8Rear Drum Assy R2000H Rear Drum AssySprocket 70 Tooth BearingSCREW, HEX 5/8 Drive System Assy R2000H Drive System AssyPULLEY, Engine 6 MM Honda GX240K1QAE2WASHER, Flat 3/8 ClipTransmission Assy R2000H Transmission AssyLEVER, Free Flow Relief Adjustment RODROD, Adjustment PUMP, HydrostaticWater System Assy R2000H Water System AssyCAP, Plastic Water Tank TANK, WaterWasher 5/16 Flat W Washer 5/16 LockAIR Cleaner Assy Honda GX240K1QAE2 Engine AIR Cleaner AssyCollar B, AIR Cleaner COVER, AIR CleanerGROMMET, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy Honda GX240K1QAE2 Engine Camshaft AssyLifter Valve SPRING, Weight ReturnROD Push ARM Valve RockerCarburetor Assy Honda GX240K1QAE2 Engine Carburetor AssyFloat SET PLATE, Lever SettingGasket SET Valve SET, FloatControl Assy Honda GX240K1QAE2 Engine Control AssySPRING, Throttle Return ARM, GovernorROD, Governor SPRING, GovernorCrankcase Cover Assy Honda GX240K1QAE2 Engine Crankcase Cover AssyGASKET, Case Cover WEIGHT, GovernorHOLDER, Governor Weight PIN, Governor WeightCrankshaft Assy Honda GX240K1QAE2 Engine Crankshaft Assy90745ZE2600 KEY 6.3 X 6.3 X 961006206000 WEIGHT, BalancerCylinder Barrel Assy Honda GX240K1QAE2 Engine Cylinder Barrel AssyOIL Seal Switch ASSY., OIL LevelSHAFT, Governor ARM BOLT, Drain PlugCylinder Head Assy Honda GX240K1QAE2 Engine Cylinder Head AssyGASKET, Cylinder Head GUIDE, VALVE, OS, OptionalGUIDE, EX. VALVE, OS, Optional CLIP, Valve GuideFAN Cover Assy Honda GX240K1QAE2 Engine FAN Cover AssyGROMMET, Drain Hole CLIP, Wire HarnessCLIP, Tube ShroudFlywheel Assy Honda GX240K1QAE2 Engine Flywheel AssyKEY, Special Woodruff FAN, CoolingFlywheel Comp NUT, Special 16MMFuel Tank Assy Honda GX240K1QAE2 Engine Fueltank AssyFILTER, Fuel Rubber Supporter 107MMJOINT, Fuel Tank GASKET, Fuel Filler CAPIgnition Coil Assy Honda GX240K1QAE2 Engine Ignition Coil AssyHOLDER, Stop Switch Wire CLAMP, WireGROMMET, Wire WIRE, Stop Switch 370MMStarter Motor Assy Honda GX390K1QAE2 Starter Motor AssyClutch Overrunning WIRE, Water CoverContactor Assy ArmatureHonda GX240K1QAE2 Control BOX Assy FUSE, Blade 15A Alert UNIT, OIL Control BOX AssyCLIP, Purse Lock TUBE, FastenerMuffler Assy Honda GX240K1QAE2 Engine Muffler AssyPIPE, EX MufflerProtector COMP., Muffler PROTECTOR, EX. PipePiston Assy Honda GX240K1QAE2 Engine Piston AssyPISTON, Standard BOLT, Connecting RODRing SET, PISTON, STD Ring SET, PISTON, 0.75, OptionalRecoil Starter Assy Honda GX240K1QAE2 Engine Recoil Starter AssySPRING, Starter Return PULLEY, Recoil StarterRATCHET, Starter SPRING, FrictionEngine Labels Honda GX240K1QAE2 Engine Engine LabelsMARK, OIL ALERT, E EMBLEM, InternalLABEL, Caution MARK, CHOKE, ExternalTerms and Conditions of Sale Parts Page HERE’S HOW to GET Help
Related manuals
Manual 90 pages 21.37 Kb

R2000H specifications

The Multiquip R2000H is a versatile and robust portable generator designed to meet the demands of construction sites, rental industries, and various outdoor events. Known for its reliability and performance, this generator stands out with several key features and technologies that cater to diverse power needs.

One of the main features of the R2000H is its powerful engine. The generator is equipped with a reliable Honda GX390 engine, providing a starting output of 2000 watts and a running output of 1800 watts. This ensures ample power to run essential tools and equipment, such as drills, saws, and lights, effectively and efficiently.

The R2000H showcases advanced inverter technology, which offers clean and stable power that is crucial for sensitive electronic equipment. This feature makes it ideal for job sites where precision and protection of equipment are paramount. Inverter technology also ensures fuel efficiency, allowing for longer run times on a single tank of gas, making it an economical choice for extended use.

Portability is another significant characteristic of the Multiquip R2000H. It is designed with a compact structure and lightweight construction, making it easy to transport from one location to another. The integrated wheels and folding handle allow for smooth mobility, thus enhancing its usability on various job sites or recreational activities.

Additionally, the R2000H is constructed with durability in mind. The robust frame protects the generator from the rigors of job site challenges, while also incorporating features like a quiet muffler to reduce operating noise. This is particularly beneficial for users who need to operate the generator in noise-sensitive environments.

User-friendly controls make the R2000H accessible for novice users, while also providing necessary functionalities for experienced operators. The intuitive panel features multiple outlets, enabling the simultaneous use of different tools, and an easy-to-read fuel gauge that allows users to monitor fuel levels with confidence.

Overall, the Multiquip R2000H combines power, efficiency, and convenience, making it an excellent choice for various applications. Whether powering professional tools on a construction site or providing backup power during outdoor events, this generator is designed to deliver reliable performance with outstanding features and technologies.
Top Page Image Contents