REAR PANEL
q w y e!5 r | t u | i o |
yRS-232C
The
The
!2 Subwoofer Output
Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer
ENGLISH
|
|
|
|
|
|
| DVD |
| DSS/VCR2 |
|
|
|
|
|
| ||
|
|
| ANTENNA |
|
|
|
|
|
|
|
|
| COMPONENT |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| VIDEO |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MONITOR OUT |
| |
FM (75‰) | GND | AM |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Y | CB/PB | CR/PR | Y | CB/PB | CR/PR | Y | CB/PB | CR/PR |
| ||
VIDEO |
|
|
|
|
|
| TV |
|
| VCR1 |
|
|
|
|
| ||
TV | DVD |
| VCR1 | DSS/VCR2 | MONITOR | MULTI | TV | DVD |
| VCR1 |
| DSS/VCR2 | MONITOR |
| |||
|
| IN | OUT | IN | OUT | OUT | OUT |
|
|
| IN | OUT | IN | OUT | OUT |
| |
@0 |
|
|
|
|
|
|
|
|
| OUTPUT |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| DIGITAL IN | DIGITAL OUT |
|
| MULTI RC |
| FLASHER IN |
| L | SL | SBL | C | |||||
|
|
|
| COAX. |
|
|
|
| IN | 1 |
|
| 2 |
|
|
|
|
4 | 5 | 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PRE | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OUT |
1 | 2 | 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OPT. |
|
|
|
| OUT | 1 | DC OUT | 2 |
|
|
|
| |
|
|
|
|
|
|
|
|
| R | SR | SBR | SW | |||||
TV | DVD |
| VCR1 | DSS/VCR2 | CD | TAPE | CDR/MD | MULTI | L | SL | SBL | C | |||||
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7.1CH |
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN | OUT | IN | OUT | IN | OUT | IN | OUT OUT | R | SR | SBR | SW |
|
|
|
| AUDIO |
|
|
| (AUX2) |
|
|
|
|
| OFF |
|
|
|
|
| SPEAKER C |
|
|
|
| |
|
| ON |
|
|
|
|
R | L |
|
|
|
|
|
SURROUND BACK/ |
|
|
|
|
| |
MULTI SPEAKER/ |
|
|
| AC OUTLET | ||
SPEAKER C |
|
|
| |||
|
|
|
| AC IN | 230V | 50/60HZ |
|
|
|
|
| SWITCHED | |
|
|
|
|
| 100W MAX. | |
R | L | R | L |
| R | L |
FRONT A | FRONT B | CENTER SURROUND | ||||
SPEAKER SYSTEMS |
|
|
|
|
| |
FRONT A OR B, CENTER, SURR, SURR BACK |
|
| ||||
FRONT A + B | : 6 |
|
|
|
| |
: 8 | OHMS |
|
|
|
|
uPreamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right).
Use these jacks for connection to external power amplifiers.
iAC INLET
Plug the supplied power cord into this AC INLET and then into the power outlet on the wall. SR7500 can be powered by 230V AC only.
oAC OUTLETS
amplifier.
!3 7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, SACD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs.
!4 DC TRIGGER output terminal
Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the conditions by which these jack will be active.
Note:
!9 | !8 | !7!6 !5!4!3!2!1 | !0 |
Connect the AC power cable of component such as a DVD or CD player to this outlet.
•This output voltage is for (status) control only, It is not sufficient for drive capability.
qVIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2) These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and
The 2 video output channels can be used to be connected to video tape recorders for making recordings.
wFM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.
eCOMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR7500. The SR7500 has 4 component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device.
By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail.
rFLASHER IN (Flasher input terminal) These terminals are to control the unit from each zone. Connect the control signal from a Keypad, etc.
tMONITOR OUT
The marked SWITCHED provides power only when the SR7500 is turned on and is useful for components which you use every time you play your system.
Caution:
•In order to avoid potential
•The capacity of this AC outlet is 100W. Do not connect devices that consume electricity more than the capacity of these AC outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.
!0 Speaker outputs terminals
Seven terminals are provided for the front (A) left, front (A) right, front (B) left, front (B) right, front center, surround left and surround right speakers.
!1 Speaker outputs terminals (SURROUND BACK / MULTI SPEAKER / SPEAKER C)
Two terminals are provided for the front left, and right speakers for multi room (2nd zone) or
!5 Multiroom Outputs (Audio L&R, Video)
These are the audio and video output jacks for the Multi zone (Multi room).
Connect these jacks to optional audio power amplifiers or video display devices to listen and view the source selected by the multiroom system in a remote room.
!6 MULTI ROOM REMOTE IN/OUT terminals
IN: Connect to a
OUT: Connect to the Marantz component equipped with remote control
!7 REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with remote control
These are monitor outputs and each one includes both composite video and
surround back.
The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 17.
7