1INPUT SETUP (ASSIGNABLE DIGITAL INPUT)
6 digital inputs can be assigned to a desired source.
With the SR8500,
Use this menu to select the digital input jack to be assigned to the input source.
1. Select “INPUT SETUP” in SETUP MAIN MENU with or cursor button, and press the ENTER button.
| 1 I N P U T S E T U P |
|
| |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| C D | : |
|
|
| D V I 1 : DV D |
|
|
|
| ||||||||||||
| D 6 - A T |
|
| |||||||||||||||||||
| T A P E : ANA |
|
| D V I 2 : DS S |
|
|
|
| ||||||||||||||
| C D - R | : D 1 - A T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| SR8500 only |
|
| ||||||||||||||||
| T V | : D 4 - A T |
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| D V D : D 5 - A T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| V CR 1 | : ANA |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| D S S : D 2 - A T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| A U X 1 | : D - A T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| MA I N |
|
|
|
|
|
|
|
|
|
|
|
|
| E X I T |
|
| |||||
2. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
To select the input source, press the |
| or | ||||||||||||||||||||
| cursor buttons. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
3. To select the digital input jack, press the | or |
cursor buttons.
Select
detection of the digital input signal condition. If there is not a digital signal present, but there is an analog signal present, the analog signal will be played.
Select “Dig x”, when only a digital signal will be used. Select “ANA” for input sources for which no digital input jacks are used.
4. To select the video source, select “DVI1” or “DVI2” by pressing the or cursor buttons, and press the or cursor buttons to select the video source to be assigned .(SR8500 only)
5. After you complete this portion of the set up, move the cursor to MAIN with the or cursor buttons and press the ENTER button.
Notes:
•The TUNER and AUX2 are fixed to the analog input, and cannot be selected for any digital input.
•When a
•If
2 SPEAKER SETUP
After you have installed the SR7500, connected all the components, and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout.
Before you perform the following settings, it is important that you first determine the following characteristics:
Speakers are set up by selecting either MANUAL or AUTO using the and cursor buttons. For operation when AUTO has been selected, see MRAC on page 21.
2 - 1 S P E AK E R S E T U P
S P E AKE R S S E T U P : MANUA L
MA I N | N E X T E X I T |
When setting the speaker size in the SPEAKER SIZE
LARGE:
The complete frequency range for the channel you are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting lower than approx. 100 Hz will be output from the subwoofer.
If the Subwoofer is set to “NONE” and the front speakers are set to “LARGE,” then the sound will be output from both the left and right speakers.
2 - 2 S P E AK E R S S I Z E |
| ||
S UBWOOF E R |
| : | Y E S |
F RON T L / R |
| : | SMA L L |
C E N T ER |
| : | SMA L L |
S URROU ND | L / R | : | SMA L L |
S URR . B ACK |
| : | 1 CH |
S URR . B ACK | S I Z E | : | SMA L L |
L P F / HP F |
| : 1 0 0 H Z | |
B A S S M I X |
| : BO T H |
MA I N RE T URN NE X T E X I T
1. Select 2. SPEAKER SETUP on the SETUP MAIN MENU, then select MANUAL for
SPEAKER SETUP.
2. To select the each speaker, press the or cursor buttons.
3. To select the setting of each speaker size, press the or cursor buttons.
4. After you complete this portion of the set up, move the cursor to “NEXT” with the or cursor buttons and then press the ENTER button to go to the next page.
THX SPEAKER SYSTEM
If you use full THX speaker systems which are approved by THX Ltd. the front, the center and surround speaker size should be ”Small” and the subwoofer should be “Yes”.
You need to set number of surround back speaker only.
SUBWOOFER
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
•If “NONE” is selected for the Subwoofer setting, then this setting is fixed to “LARGE.”
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are connected.
LARGE:
Select if the surround left and right speakers are large.
SMALL:
Select if the surround left and right speakers are small.
SURR. BACK
NONE:
Select if no surround back left and right speakers are connected.
2CH:
Select if the surround back left and right speakers are connected.
1CH:
Select if the one surround back speaker is connected.
In this case, the audio signal is emitted form the Surround L output terminal.
Notes:
•If “NONE” is selected for the Surround L/R setting, then this setting is fixed to “NONE.”
•You can use surround back speaker terminals as multi room speaker terminals when you use no surround back speaker. (See page 17)
SURR. BACK SIZE
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
Note:
•If “NONE” is selected for the Surround L/R setting, then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the cutoff frequency for the small speakers used. Select one of the crossover frequency levels according to the size of the small speaker connected.
80Hz:
Select this when the bass speaker is about 12 cm (4 3/4 inches).
100Hz:
Select this when the bass speaker is about 10 cm (3 15/16 inches).
120Hz:
Select this when the bass speaker is about 8 cm (3 3/16 inches).
Notes:
•Use the above comments as reference when adjusting.
•If
ENGLISH
19