Marantz SR7500, SR8500 manual Press the button to display the second page Setup menu

Page 49

If the copying fails in the middle of the copying process, ERROR is displayed on the remote control.

Check and perform steps 1 to 7 again.

11.Once copying is completed, press the M button on both remote controls.

SETUP

SETTING THE LIGHTING TIME

The LCD lights up when the LIGHT buttons are pressed. The LCD remains lit while the pressed button is held down, and it goes off when the button is released.

The LCD continues to light up if another button is pressed while it is lit or if pressed within two seconds after the light goes off.

The lighting time can be set in one-second units from 0 to 60 seconds.

The LIGHT buttons have light - absorbing properties that enable them to store light. If the buttons are no longer illuminated in a dimly lit environment, bring the buttons near a fluorescent lamp or other light source for a sufficient amount of time. This should illuminate the buttons again.

The LIGHT buttons consist of a LIGHT1 and LIGHT2 button, and they both perform the same operation.

The factory default lighting time is set to 15 seconds.

This example shows how to set the lighting time to 20 seconds.

2

3

 

 

 

 

4

 

 

 

 

LEARN

 

 

 

 

LEARN

 

 

 

PAGE 1

2

1

2

3

4

1

2

3

4

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button to display the second page SETUP menu.

3. Press the D1 (LIGHT) direct button . The LIGHT is displayed on the LCD

4. Press the or cursor button to set the lighting time.

5. Press the OK cursor button to enter the lighting time.

6. Once the setting is finished, press the M button .

SETTING THE MACRO INTERVAL TIME

When a macro program is executed, control signals are transmitted in sequence. This transmission interval (interval time) can be set in 0.5-seconds units from 0.5 to 5 seconds.

If the interval time is set in this Setup mode, the interval times for all programmed macros are changed. If necessary, use EDIT (see page 43) in the macro program to change the individual transmission times.

The factory default setting for the transmission interval is 1 second.

This example shows how to set the interval time to 5 seconds.

2

3

 

 

 

 

4

 

 

 

 

LEARN

 

 

 

 

LEARN

 

 

 

PAGE 1

2

1

2

3

4

1

2

3

4

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button to display the second page SETUP menu.

3. Press the D2 (I-TIME) direct button.

4. Press the or cursor button to set the interval time.

Holding down the cursor button fast-forwards the time indicator.

5. Press the OK cursor button to enter the interval time.

6. Once the setting is finished, press the M button.

ADJUSTING THE DISPLAY CONTRAST

The contrast of the LCD can be adjusted. Adjust for maximum visibility according to your viewing environment.

2

3

 

 

 

 

4

 

 

 

 

LEARN

 

 

 

 

LEARN

 

 

 

PAGE 1

2

1

2

3

4

1

2

3

4

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button to display the second page SETUP menu.

3. Press the D3 (CONT) direct button .

4. Press the or cursor button and set the display contrast for maximum visibility.

The adjustment has 10 levels.

The factory default setting for the contrast is the fifth level.

5. Press the OK cursor button to enter the display contrast.

6. Once the setting is finished, press the M button.

ENGLISH

45

Image 49
Contents Model SR7500/SR8500 User Guide Français EnglishDeutsch NederlandsFrançais EnglishDeutsch NederlandsItaliano EspañolPortuguês SvenskaIntroduction Table of Contents ForewordDescription SR8500 only About Dolby Pro LogicAccessories FeaturesRemote Controller RC8500SR THX Select certifiedFront Panel How to Attach the Front AUX Jack CoverOpening and closing the front panel door FL Display and IndicaterPCM Rear Panel Names and Functions Sleep sleep timer button LCD IndicatorsDISP. button OSD buttonBattery Replacement Interval Remote Control RangeSetting the Time Safety Precautions for BatteriesTuner Mode AMP ModeGeneral Information Checking the TimeConnections Speaker PlacementConnecting Digital Audio Components Connecting Audio ComponentsThere are 3 types of video jacks on the rear panel Connecting Video ComponentsVideo jack Component jackConnecting Multi Channel Audio Source Advanced ConnectingConnecting AN External Power Amplifier Connecting the supplied FM antenna Connecting the Antenna TerminalsConnecting the supplied AM loop antenna Place the antenna on stable surfaceBi-wire Connection Connecting for the Multi RoomMultiroom On Screen Display Menu System SetupOr or cursor buttons Input Setup Assignable Digital Input Speaker SetupFront L Test ModeFront R CenterMeasurement How to OperatePreference Error Indications During MeasurementPL II PRO Logic II Music Parameter CS II Circle Surround II ParameterMulti Room DC Trigger SetupCH Input Level Basic Operation Using the Sleep Timer Surround ModeNight Mode Temporarily Turning OFF SoundDTS-ES Discrete 6.1, Matrix Dolby Digital EXDts, Neo6 Cinema, Neo6 Music Neo6 Cinema, Neo6 MusicSR8500 only SBR Other Function Speaker A/B Recording AN Analog SourceCH Input LIP.SYNC AUX2 InputListening to the Tuner Or enter the preset station number with the numeric buttons Preset MemoryManual Preset Memory Recalling a Preset Station Preset Scan Auto Preset Memory← Down → B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP →Some RDS stations broadcast Radio Text RDS OperationCompletely received Multi Room Playback Using Multi Room Playback Using Multi Speaker TerminalsMulti Room SystemControlling a Marantz VCR VCR Mode Remote Controller OperationControlling Marantz Components Turns the CD recorder on and off Basic Operation When operating non-Marantz AV equipment productsNormal operation status Rewriting Names Erasing direct buttons Erasing buttonsProgramming Macros Press the 5 numeric button to select M When clearing macros, the macros programmed toPress the cursor button to next Repeat steps 6 and 7, and then enter V, I, ETransmitting remote control Clone ModeReceiving remote control Press the button to display the second page Setup menu SetupSetting the Lighting Time Setting the Macro Interval TimeSymptom Cause Remedy TroubleshootingDimensions Technical SpecificationsAmplifier Setup CodesRECEIVER/TUNER Source button name AMPLaser Disk Tape DeckCD/CD-R Player Iii Source button name TV Source button name VCR VCRSource button name DVD DVDSource button name Tuner Direct Button FunctionsSource button name CD Source button name CDREurope Japan