Marantz SR8500 Preference, PL II PRO Logic II Music Parameter, CS II Circle Surround II Parameter

Page 26

ENGLISH

Notes:

The measured speaker distance may differ from the actual distance from speakers. Nevertheless, the measured value is suitable for the speakers.

To make changes to individual speakers, select 2. SPEAKER SETUP on the SETUP MAIN MENU, then select MANUAL for 2-1 SPEAKER SETUP.

The included microphone is designed specifically for this receiver. Other microphones do not guarantee suitable measurement results. Use the included microphone to conduct measurements.

During measurement, press the ENTER or EXIT button to cancel measurement.

In some rooms, an error may occur during auto speaker setup or it may not be possible to set Speaker distance correctly because of room acoustics. In such case, set the speaker distance by MANUAL setup.

Error Indications During Measurement

If trouble occurs during measurement, an error message is displayed on the monitor screen and FL display. Those errors and their remedies are described below. The message appearing on the FL display is given in ( ).

MIC SETUP ERROR (MIC SET ERROR)

The microphone (MC-10) is not properly connected.

Check the microphone connection.

AMBI NOISE ERROR (AMBI NOISE ER)

Measurement cannot be done correctly because of excessive ambient noise.

Either temporarily turn off power to noisy devices such as air conditioning or move them out of the room.

Retry measurement when the room is quiet.

SPEAKER SET ERROR (SPK SET ERROR)

The speakers are not properly connected.

Recheck speaker layout and connections.

3 PREFERENCE

3 P RE F E RENCE

 

 

 

S T ANDB Y MODE

:

 

 

E CONOMY

T V - AU T O

:

D I SAB L E

OSD I N FO

:

E NAB L E

V I DEO CONV ER T

:

E NAB L E

L F E L E V E L

:

0 d B

MA I N

 

E X I T

 

 

 

 

1. Select “PREFERENCE” in the SETUP MAIN MENU with the or cursor buttons, and press the ENTER button.

2. To select a desired content, press the or cursor buttons.

STANDBY MODE:

When this function is set to “ECONOMY”, you can reduce the power consumption when the unit is in the standby mode.

Note:

TV-AUTO and RS-232C are disabled in the “ECONOMY” setting.

TV AUTO:

Select the TV AUTO ON/OFF function to enable or disable with the or cursor buttons. (refer to page 29)

OSD Info:

Select the OSD information function to enable or

disable with the or cursor buttons.

If you select “ENABLE”, the SR7500 will display the status of the feature (Volume up/down, input select, etc..) on the TV monitor. But if you do not desire this information, select “DISABLE ”.

VIDEO CONVERT:

Select the VIDEO CONVERT function to enable or disable with the or cursor buttons. (Video cable connection: Refer to page 24)

LFE LEVEL:

Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0 dB, -10 dB or OFF with the or cursor buttons.

After you complete this portion of the set up, move the cursor to “MAIN” with the or cursor buttons and press the ENTER button.

4PL II (PRO LOGIC II) MUSIC PARAMETER

Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs.

In this mode, SR7500 includes three controls to fine-tune the soundfield as follows.

4 P L II MUS I C

PARAME T E R

PARAME T ER

:

 

 

DE F AU L T

PANORAMA

: OF F

D I MEN S I ON

:

4

 

CEN T E R W I D T H

:

0

 

MA I N

 

E X I T

 

 

 

 

Select “PL II MUSIC” in the SETUP MAIN MENU with the or cursor buttons, and press the ENTER button.

PARAMETER:

Select “DEFAULT” or “CUSTOM” with the or cursor buttons.

If you select “CUSTOM”, you can adjust three parameters as listed below.

PANORAMA:

Select the Panorama mode On or Off with the or cursor buttons.

Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective.

DIMENSION:

Set the Dimension level between 0 and 6 level in 1 level intervals with the or cursor buttons. Adjust the soundfield either towards the front or towards the rear.

This can be useful to help achieve a more suitable balance from all the speakers with certain recordings.

CENTER WIDTH:

Set the Center width level between 0 and 7 in 1 level intervals with the or cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers.

At its widest setting, all the sound from the center is mixed into the left and right.

This control may help achieve a more spacious sound or a better blend for the front image.

If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear.

After you complete this portion of the set up, move cursor to “MAIN” with the or cursor buttons and press the ENTER button.

5CS II (CIRCLE SURROUND II) PARAMETER

5 C S II PARAME T E R

T RUBA S S

:

0

SRS D I A LOG

:

0

MA I NE X I T

1. Select “CS II” in the SETUP MAIN MENU with

the or cursor buttons, and press the ENTER button.

2. To Select desired contents as below, press the or cursor buttons.

TRUBASS:

Set the TRUBASS level between 0 and 6 level in 1 level interval with the or cursor buttons.

TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects.

SRS DIALOG:

Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the or cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say.

If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear.

After you complete this portion of the set up, move cursor to “MAIN” with the or cursor buttons and press the ENTER button.

22

Image 26
Contents Model SR7500/SR8500 User Guide Deutsch EnglishFrançais NederlandsDeutsch EnglishFrançais NederlandsPortuguês EspañolItaliano SvenskaTable of Contents Foreword IntroductionDescription About Dolby Pro Logic SR8500 onlyRemote Controller RC8500SR FeaturesAccessories THX Select certifiedHow to Attach the Front AUX Jack Cover Front PanelPCM FL Display and IndicaterOpening and closing the front panel door Rear Panel Names and Functions DISP. button LCD IndicatorsSleep sleep timer button OSD buttonSetting the Time Remote Control RangeBattery Replacement Interval Safety Precautions for BatteriesGeneral Information AMP ModeTuner Mode Checking the TimeSpeaker Placement ConnectionsConnecting Audio Components Connecting Digital Audio ComponentsVideo jack Connecting Video ComponentsThere are 3 types of video jacks on the rear panel Component jackConnecting AN External Power Amplifier Advanced ConnectingConnecting Multi Channel Audio Source Connecting the supplied AM loop antenna Connecting the Antenna TerminalsConnecting the supplied FM antenna Place the antenna on stable surfaceMultiroom Connecting for the Multi RoomBi-wire Connection Or or cursor buttons SetupOn Screen Display Menu System Speaker Setup Input Setup Assignable Digital InputFront R Test ModeFront L CenterHow to Operate MeasurementPL II PRO Logic II Music Parameter Error Indications During MeasurementPreference CS II Circle Surround II ParameterCH Input Level DC Trigger SetupMulti Room Basic Operation Night Mode Surround ModeUsing the Sleep Timer Temporarily Turning OFF SoundDts, Neo6 Cinema, Neo6 Music Dolby Digital EXDTS-ES Discrete 6.1, Matrix Neo6 Cinema, Neo6 MusicSR8500 only SBR Other Function CH Input Recording AN Analog SourceSpeaker A/B AUX2 Input LIP.SYNCListening to the Tuner Manual Preset Memory Recalling a Preset Station Preset Scan Preset MemoryOr enter the preset station number with the numeric buttons Auto Preset Memory→ B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP → ← DownCompletely received RDS OperationSome RDS stations broadcast Radio Text Multi Room Multi Room Playback Using Multi Speaker TerminalsMulti Room Playback Using SystemControlling Marantz Components Remote Controller OperationControlling a Marantz VCR VCR Mode Turns the CD recorder on and off Normal operation status When operating non-Marantz AV equipment productsBasic Operation Rewriting Names Erasing buttons Erasing direct buttonsProgramming Macros Press the cursor button to next When clearing macros, the macros programmed toPress the 5 numeric button to select M Repeat steps 6 and 7, and then enter V, I, EReceiving remote control Clone ModeTransmitting remote control Setting the Lighting Time SetupPress the button to display the second page Setup menu Setting the Macro Interval TimeTroubleshooting Symptom Cause RemedyTechnical Specifications DimensionsRECEIVER/TUNER Setup CodesAmplifier Source button name AMPCD/CD-R Player Tape DeckLaser Disk Iii VCR Source button name TV Source button name VCRDVD Source button name DVDSource button name CD Direct Button FunctionsSource button name Tuner Source button name CDRJapan Europe