Marantz SR7500, SR8500 manual AUX2 Input, Lip.Sync

Page 35

1.2.

 

AV SURROUND RECEIVER SR7500

 

 

 

 

INPUT SELECTOR

 

 

 

 

 

 

CH

VOL

 

 

E

4.

 

POWER ON/OFF

PHONES

 

 

 

OK

4.

4.

 

PREV

LIP.SYNC

MUTE

 

 

 

 

GUIDE

 

3.

MENU

 

EXIT

 

TEST

CH.SEL

SURR

 

1

2

3

 

7.1CH

ATT

SPK-AB

VOLUME

2.

4

5

6

 

DISP

THX

SLEEP

 

 

OSD

 

 

7

8

9

DOWN

UP

CLEAR

0

MEMO

AUX 1 INPUT

 

 

 

 

DIGITALS-VIDEO VIDEO

L AUDIO R

 

 

 

1. Select a desired Video source to decide the routed video signal to the Monitor Outputs.

2. Press the 7.1 CH INPUT button on the front panel or press 7.1 CH on the remote to switch the 7.1 channel input.

3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the remote.

Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between –10 to +10 dB. The subwoofer can be adjusted between –15 and +10 dB.

These adjustments result will be stored to 7.1

CH. INPUT memory.

4. Adjust the main volume with the MAIN

VOLUME knob or the VOL buttons on the

remote.

To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH on the remote.

Notes:

When the 7.1 CH. Input is in use, you may not select a surround mode, as the external decoder determines processing.

In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use.

AUX2 INPUT

If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder,

L(front left) and R (front right) inputs terminals are available as AUX2 input.

In this case, You can connect additional audio source to AUX2 as other audio input terminals.

AV SURROUND RECEIVER SR7500

INPUT SELECTOR

POWER ON/OFF

PHONES

LIP.SYNC

Depending on the image device (TV, monitor, projector, etc.) connected to the SR7500, a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the SR7500 to correct the time lag between the sound and image. It can be operated with the “LIP.SYNC” and and cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.

Note:

The LIP.SYSNC feature turns OFF (0 ms) in the PURE DIRECT mode. When the PURE DIRECT mode is deactivated, the set value of the LIP.SYSNC feature is automatically restored.

CH

 

VOL

 

OK

 

 

LIPLIP..SYNCSYNC

 

PREV

 

MUTE

 

GUIDEGUIDE

 

MENU

 

EXIT

TEST

CH.SEL

SURR

1

2

3

7.1CH

ATT

SPK-AB

4

5

6

DISP

OSD

SLEEP

7

8

9

 

THX

 

CLEAR

0

MEMO

ENGLISH

31

Image 35
Contents Model SR7500/SR8500 User Guide Nederlands EnglishFrançais DeutschNederlands EnglishFrançais DeutschSvenska EspañolItaliano PortuguêsIntroduction Table of Contents ForewordDescription SR8500 only About Dolby Pro LogicTHX Select certified FeaturesAccessories Remote Controller RC8500SRFront Panel How to Attach the Front AUX Jack CoverPCM FL Display and IndicaterOpening and closing the front panel door Rear Panel Names and Functions OSD button LCD IndicatorsSleep sleep timer button DISP. buttonSafety Precautions for Batteries Remote Control RangeBattery Replacement Interval Setting the TimeChecking the Time AMP ModeTuner Mode General InformationConnections Speaker PlacementConnecting Digital Audio Components Connecting Audio ComponentsComponent jack Connecting Video ComponentsThere are 3 types of video jacks on the rear panel Video jackConnecting AN External Power Amplifier Advanced ConnectingConnecting Multi Channel Audio Source Place the antenna on stable surface Connecting the Antenna TerminalsConnecting the supplied FM antenna Connecting the supplied AM loop antennaMultiroom Connecting for the Multi RoomBi-wire Connection Or or cursor buttons SetupOn Screen Display Menu System Input Setup Assignable Digital Input Speaker SetupCenter Test ModeFront L Front RMeasurement How to OperateCS II Circle Surround II Parameter Error Indications During MeasurementPreference PL II PRO Logic II Music ParameterCH Input Level DC Trigger SetupMulti Room Basic Operation Temporarily Turning OFF Sound Surround ModeUsing the Sleep Timer Night ModeNeo6 Cinema, Neo6 Music Dolby Digital EXDTS-ES Discrete 6.1, Matrix Dts, Neo6 Cinema, Neo6 MusicSR8500 only SBR Other Function CH Input Recording AN Analog SourceSpeaker A/B LIP.SYNC AUX2 InputListening to the Tuner Auto Preset Memory Preset MemoryOr enter the preset station number with the numeric buttons Manual Preset Memory Recalling a Preset Station Preset Scan← Down → B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP →Completely received RDS OperationSome RDS stations broadcast Radio Text System Multi Room Playback Using Multi Speaker TerminalsMulti Room Playback Using Multi RoomControlling Marantz Components Remote Controller OperationControlling a Marantz VCR VCR Mode Turns the CD recorder on and off Normal operation status When operating non-Marantz AV equipment productsBasic Operation Rewriting Names Erasing direct buttons Erasing buttonsProgramming Macros Repeat steps 6 and 7, and then enter V, I, E When clearing macros, the macros programmed toPress the 5 numeric button to select M Press the cursor button to nextReceiving remote control Clone ModeTransmitting remote control Setting the Macro Interval Time SetupPress the button to display the second page Setup menu Setting the Lighting TimeSymptom Cause Remedy TroubleshootingDimensions Technical SpecificationsSource button name AMP Setup CodesAmplifier RECEIVER/TUNERCD/CD-R Player Tape DeckLaser Disk Iii Source button name TV Source button name VCR VCRSource button name DVD DVDSource button name CDR Direct Button FunctionsSource button name Tuner Source button name CDEurope Japan