Marantz SR8500, SR7500 manual Rewriting Names

Page 44

ENGLISH

 

LEARN MODE

 

 

 

 

 

 

Programming the

(PLAY) and Other Control

 

Buttons and Numeric Buttons

 

This remote control is capable of learning and

 

storing codes used by other remote controls that

 

you already own.

 

 

 

 

 

For codes which are not learned, the remote

 

control will transmit either the Marantz preset

 

codes from the initial settings, or remote codes

 

from another manufacturer’s AV equipment which

 

is set by the customer.

 

The receiver sensor for the remote control signals is

 

located at the top of the remote control.

 

This example shows how to learn the codes from

 

the remote control of a DVD player.

 

1

 

 

2

4

 

 

 

 

 

 

LEARN

 

 

LEARN

 

 

 

USEPAGE 1

 

PAGE 1 2

 

 

1 2

 

 

 

 

 

 

 

 

 

 

 

6 (When OK)

(failed)

 

(codes are full)

 

 

 

 

 

 

 

 

 

 

 

LEARN

 

LEARN

 

 

 

 

 

 

PAGE 1 2

 

PAGE 1 2

 

 

1 2

 

 

 

 

 

 

 

 

 

 

 

1. Hold down the M button for three seconds or

more.

The menu is displayed.

2. Press the D2 (LEARN) direct button.

The LEARN setting (LEARN) is displayed. The LEARN indicator then blinks.

3. Press the DVD source button.

4. Press the(PLAY) button.

The LEARN indicator blinks, and then displays to indicate that learning is ready.

5. Place the receiver sensor of the remote control (top) so that it is facing the transmitter of the DVD remote control (top) at a distance of about 5 cm (2 inches).

6. Press and hold down the(PLAY) button of the transmitting DVD remote control, and check that OK is displayed on the LCD.

The remote control has finished learning when OK is displayed on the LCD.

If ERROR is displayed on the LCD, some error has prevented the command from being learned. If this happens, repeat the procedure for steps 4 and 5.

In some rare cases, ERROR may be displayed repeatedly during the learning operation. In this case, the transmitting remote control may have special signal codes. These codes cannot be learned by this remote control.

7. Follow the same procedure to make the remote control learn the other buttons.

8. Repeat the procedure in steps 3 to 6 to have

the remote control learn the signal codes from

a TV, CD player, or other AV equipment.

•When no buttons are pressed for approximately one minute during the learning operation, the remote control automatically returns to USE mode.

•When programming the source buttons, switch to the source in step 3, and then press the source button again.

9.When you have finished programming the codes for each button, press the M button.

The USE indicator is displayed on the LCD, and the newly stored codes can be used.

•If FULL is displayed on the LCD, the memory cannot hold any more learned codes in LEARN mode.

If FULL is displayed no matter how many times you try the learning operation, the remote control cannot accept any more new codes until some of the previously learned codes are deleted from the memory. Delete some of the learned buttons from the sources.

The M button and > button cannot be taught. Only each one code can be learned for the LIGHT buttons 1 and 2, regardless of the source.

Programming the Direct Buttons and Rewriting Names

This example shows how to program codes from other manufacturer products to the DVD MENU button (D1) and change the display to OSD.

6

7

 

8

LEARN

 

LEARN

LEARN

PAGE 1

2

PAGE 1 2

PAGE 1 2

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the D2 (LEARN) direct button.

The LEARN setting (LEARN) indicator is displayed. The LEARN indicator then blinks.

3. Press the DVD source button.

The first page of the direct button screen is displayed. There are four available pages. Pressing the > buttons cycles through the pages in this order 1

→ 2 → 3 → 4 → 1.

4.Press the D1 (MENU) direct button.

The LEARN indicator blinks, and then displays to indicate that learning is ready.

5.Place the receiver sensor of the remote control (top) so that it is facing the transmitter of the DVD remote control (top) at a distance of about 5 cm (2 inches).

6.Press and hold down the OSD button of the transmitting DVD remote control, and check that OK is displayed on the LCD.

The remote control has finished learning when OK is displayed on the LCD.

If ERROR is displayed on the LCD, some error has prevented the command from being learned. If this happens, repeat the procedure for steps 4 and 5.

• After learning is completed, the remote control automatically switches to name rewriting mode. The left end “ ” indicator on the MENU blinks to indicate that the blinking part can be rewritten.

• If no names will be rewritten, press the OK cursor button. The display returns to learning standby mode by pressing the OK cursor button.

7. To change the name, press the numeric buttonsto enter the text.

•Use the cursor buttonsto move to the sections to be rewritten on the LCD.

•To change MENU to OSD, press the 5 numeric button.

Each time the button is pressed, the display cycles through M → N → O → 5 → M.

8.After rewriting of the text is completed, press the OK cursor button.

To delete text that is already entered, press the 0 button to insert a space.

•In this example, MENU is changed to “OSD (space) (space)” in this step, and then OSD is displayed in the right side by pressing the OK button.

For details, refer to the section “Rewriting Names”.

9. In the same way, use the > button to select the page, and then press the direct button to program the codes.

10. After programming the codes for each of the buttons, press the M button.

The USE indicator displays on the LCD, and the newly stored codes can be transmitted.

REWRITING NAMES

This remote control allows the rewriting of names for the sources and direct buttons. This operation is performed for each individual source.

This example shows how to change the source name from DVD to AVD and AUDIO to SOUND.

3

 

 

4

 

 

5

 

NAME

 

 

NAME

 

 

NAME

 

PAGE

1

2

PAGE

1

2

PAGE

1 2

7

 

 

8

 

 

9

 

NAME

 

 

NAME

 

 

NAME

 

PAGE

1

2

PAGE

1

2

PAGE 1

2

1. Hold down the M button for three seconds or

more.

The menu is displayed.

2. Press the D3 (NAME) direct button .

40

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Model SR7500/SR8500 User Guide English FrançaisDeutsch NederlandsEnglish FrançaisDeutsch NederlandsEspañol ItalianoPortuguês SvenskaTable of Contents Foreword IntroductionDescription About Dolby Pro Logic SR8500 onlyFeatures AccessoriesRemote Controller RC8500SR THX Select certifiedHow to Attach the Front AUX Jack Cover Front PanelPCM FL Display and IndicaterOpening and closing the front panel door Rear Panel Names and Functions LCD Indicators Sleep sleep timer buttonDISP. button OSD buttonRemote Control Range Battery Replacement IntervalSetting the Time Safety Precautions for BatteriesAMP Mode Tuner ModeGeneral Information Checking the TimeSpeaker Placement ConnectionsConnecting Audio Components Connecting Digital Audio ComponentsConnecting Video Components There are 3 types of video jacks on the rear panelVideo jack Component jackConnecting AN External Power Amplifier Advanced ConnectingConnecting Multi Channel Audio Source Connecting the Antenna Terminals Connecting the supplied FM antennaConnecting the supplied AM loop antenna Place the antenna on stable surfaceMultiroom Connecting for the Multi RoomBi-wire Connection Or or cursor buttons SetupOn Screen Display Menu System Speaker Setup Input Setup Assignable Digital InputTest Mode Front LFront R CenterHow to Operate MeasurementError Indications During Measurement PreferencePL II PRO Logic II Music Parameter CS II Circle Surround II ParameterCH Input Level DC Trigger SetupMulti Room Basic Operation Surround Mode Using the Sleep TimerNight Mode Temporarily Turning OFF SoundDolby Digital EX DTS-ES Discrete 6.1, MatrixDts, Neo6 Cinema, Neo6 Music Neo6 Cinema, Neo6 MusicSR8500 only SBR Other Function CH Input Recording AN Analog SourceSpeaker A/B AUX2 Input LIP.SYNCListening to the Tuner Preset Memory Or enter the preset station number with the numeric buttonsManual Preset Memory Recalling a Preset Station Preset Scan Auto Preset Memory→ B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP → ← DownCompletely received RDS OperationSome RDS stations broadcast Radio Text Multi Room Playback Using Multi Speaker Terminals Multi Room Playback UsingMulti Room SystemControlling Marantz Components Remote Controller OperationControlling a Marantz VCR VCR Mode Turns the CD recorder on and off Normal operation status When operating non-Marantz AV equipment productsBasic Operation Rewriting Names Erasing buttons Erasing direct buttonsProgramming Macros When clearing macros, the macros programmed to Press the 5 numeric button to select MPress the cursor button to next Repeat steps 6 and 7, and then enter V, I, EReceiving remote control Clone ModeTransmitting remote control Setup Press the button to display the second page Setup menuSetting the Lighting Time Setting the Macro Interval TimeTroubleshooting Symptom Cause RemedyTechnical Specifications DimensionsSetup Codes AmplifierRECEIVER/TUNER Source button name AMPCD/CD-R Player Tape DeckLaser Disk Iii VCR Source button name TV Source button name VCRDVD Source button name DVDDirect Button Functions Source button name TunerSource button name CD Source button name CDRJapan Europe
Top Page Image Contents