Marantz SR8500, SR7500 manual → B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP →, ← Down

ENGLISH	CLEARING STORED PRESET STATIONS
	You can remove preset stations from the memory
	using the following procedure.

2.	3.
		TEST	CH.SEL	SURR
		1	2	3
	VOLUME	7.1CH	ATT	SPK-AB
		4	5	6	3.
		DISP	OSD	SLEEP
		7	8	9
	DOWN		THX
		CLEAR	0	MEMO	2.
ENTER
	AUX 1 INP
	DIGITALS-VIDEO V

SORTING PRESET STATIONS

AV SURROUND RECEIVER SR7500

INPUT SELECTOR

ENTER

POWER ON/OFF PHONES

VOLUME

DOWN			UP
		AUX 1 INPUT
DIGITAL	S-VIDEO	VIDEO	L AUDIO R

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters.

Before name inputting, you need to store preset stations with the preset memory operation.

4.5. 2. 5. 6.

INPUT SELECTOR

UP

5. After selecting the first character to be entered, press the MEMORY or ENTER button, or press the MEMO button on the remote.

The entry in this column is fixed and the next column starts to flash. Fill the next column the same way.

To move back and forth between the characters, press the/cursor buttons or press CH+ or CH– button on the remote.

Note:

TV DVD VCR DSS

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

ENTER

POWER ON/OFF PHONES

• Unused columns should be filled by entering

blanks.

6. To save the name, press the MEMORY or

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote.

4. “xx CLEAR” appears on the display to

indicate that the specified preset number has been cleared.

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10) 105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5:

To sort the numbers, press and hold the MEMORY and thecursor buttons.

“PRESET SORT” will appear on the display and sorting will be done.

CHVOL

OK

LIP.SYNC

PREV MUTE

7 8 9

THX

CLEAR0 MEMOMEMO

5.

5.

2.

5.

6.

SOURCE

PAGE 2

M

D1D1

D2D2

D3

D4

D5D5

4.

4.

4.

ENTER button on the front panel, or press the

MEMO button on the remote for more than 2

seconds.

Ten keypad Press, press again, press again, etc.

1	A → B → C → 1 → A
2	D → E → F → 2 → D
3	G → H → I → 3 → G
4	J → K → L → 4 → J
5	M → N → O → 5 → M
6	P → Q → R → 6 → P

Note:

•To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.

1.	Recall the preset number to be inputted name
	with the method described in “Recalling” a
2.	preset station.
	Press the MEMORY button on the front panel
	or press the MEMO button on the remote for
3.	more than 3 seconds.
	The left most column of the station name
	indicator flashes, indicating the character
4.	entry ready status.
	When you press the	or	cursor buttons on
	the front panel or the	or	buttons on the

remote, alphabetic and numeric characters

will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

7	S → T → U → 7 → S
8	V → W → X → 8 → V
9	Y → Z → space → 9 → Y

0– → + → / → 0

34