Land Pride FD2572, at 2560, AT2572 Storage, Blade Replacement, Belt Installation, Belt Tension

Page 19

Land Pride

Table of Contents

Section 4: Maintenance and Lubrication

4.Check blade balance by positioning the blade horizontally on a nail or shaft through the center hole. See Figure 4-3. If either end of the blade rotates downward, grind (remove) metal on that end until the blade will balance. The blade is properly balanced when neither end drops. Balance of a blade is generally maintained by removing an equal amount of material from each end of the blade when sharpening.

HORIZONTAL

19046

NAIL OR SHAFT

Blade Balancing

Figure 4-3

Blade Replacement

IMPORTANT: Always install blade with cutting edge facing direction of blade spindle rotation and wing tips pointing up towards bottom of deck.

1.Remove cap screw and blade washer from blade to be replaced. Remove blade.

2.Install blade washer into center hole on blade.

3.Replace cap screw. Tighten bolts to proper torque, see the “Torque Values Chart” section on page 23.

IMPORTANT: Replace blades with Land Pride blades only.

AIR TIRES (AIR PRESSURE):

Tire Sealant: Heavy Duty tire sealant has been added in Air tires to help reduce air loss from punchers due to nails/thorns etc....

NOTE: Under inflated tires can roll off of rim. Maintaining air pressure within 5 PSI of maximum tire pressure reduces the risk of tires rolling off of rim.

V-Belt Installation

1. Remove right hand, left hand and center belt covers.

V-Belt Installation, Routing & Rotation Decal

Figure 4-4

2.Move belt take-up handle in a clockwise direction to relieve tension on belt.

3.With tension relieved from belt remove old belt from pulleys.

4.Install new belt referring to the figure below (also refer to the decal on top of mower deck). Be sure belt is positioned in all the pulley grooves. Release belt take-up handle to apply tension to new belt.

5.Reinstall all belt covers and secure in place with hardware.

Belt Tension

!CAUTION

Belt drive system under spring tension; use care to avoid bodily harm!

1.Belt tension should be checked after approximately 20 hours of operation on a new belt.

2.Not enough tension on the belt may lead to premature failure of the belt due to excessive slipping of the belt.

Refer to “Belt Tension” on page 15 for proper adjustment of belt tension.

!WARNING

Excessive tension on the belt may lead to premature failure of belt and drive components. Excessive tension on the belt may also lead to a safety hazard to the operator or bystanders.

Storage

At the end of the working season or when the mower will not be used for a long period, it is good practice to clean off any dirt or grease that may have accumulated on the mower and any of the moving parts. It may be necessary to scrape off compacted dirt from the bottom of the deck, then use a garden hose to thoroughly clean the surface.

1.Clean the mower as necessary. Be sure that the mower is completely cleaned before storing.

2.Check the blades for wear and replace if necessary, see “Maintenance” section on page 16.

3.Inspect the mower for loose, damaged or worn parts and adjust or replace if needed.

4.Lubricate as noted in the “Lubrication” section on page 18.

5.Remove mower drive belt from one pulley to release drive belt tension.

6.Remove belt guards, thoroughly clean the top and bottom of the mower frame.

7.Repaint parts where paint is worn or scratched to prevent rust. Aerosol beige touch-up paint is available from your dealer. Order Land Pride part #821-011C.

8.Store mower in a clean, dry place for longer mower life.

10/11/06

FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M

17

Image 19
Contents Grooming Mower, 3-spindle Table of Contents Safety at All Times Practice Safe Maintenance Important Safety InformationUse Safety Lights and Devices Use a Safety ChainKeep Riders Off Machinery Tire SafetyPrepare for Emergencies Wear Protective Equipment818-555C Safety Labels818-130C 818-556C818-144C 818-142C818-552C 818-540COwner Assistance Using This ManualIntroduction Assembly & Set-up Assembly InstructionsGeneral Description Grass Chute Assembly Gauge Wheel AssemblyFinal Inspection Tractor Requirements Driveline InstallationPre-Start Instructions Operating InstructionsChecking Driveline Minimum Length Operating Instructions Pre-Start-up ChecklistTransporting Leveling The Mower Floating & Front To Back Hitch AdjustmentsAdjustments Mower ChuteBelt Tension Cutting Height AdjustmentBlade Sharpening General MaintenanceMaintenance and Lubrication Blade InspectionBelt Tension Blade ReplacementBelt Installation StorageHours LubricationBearing in Blade Spindle Hubs SeasonallyWheel Bushing Martin Wheel Bushing NeilsonOptions FD2560, FD2572, AT2560 & AT2572 3-Spindle Grooming Mower Specifications & CapacitiesDescription FD2560 FD2572 AT2560 AT2572 Troubleshooting Chart TroubleshootingProblem Cause Solution Tire Inflation Chart Torque Values ChartAppendix Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

FD2572, FD2560, AT2572, at 2560 specifications

Land Pride is a well-respected manufacturer in the agricultural and landscaping equipment sector, renowned for its commitment to quality, durability, and performance. Among its key offerings, the AT2560, AT2572, FD2560, and FD2572 stand out due to their innovation, functionality, and versatility.

The AT2560 and AT2572 are part of Land Pride's series of ATV and UTV attachments designed to enhance productivity in landscaping and maintenance tasks. These implements facilitate tasks such as grading, leveling, and debris management. The rugged construction ensures they can withstand the rigors of tough outdoor environments. Key features include a reinforced frame, adjustable blade angles, and the ability to easily attach and detach from various vehicles. They are designed for optimal performance, providing operators with the confidence needed to tackle diverse terrain with efficiency.

On the other hand, the FD2560 and FD2572 are versatile finish mowers, perfect for achieving a professional cut in various applications, including residential lawns, commercial properties, and sports fields. These mowers are equipped with advanced features like a floating mower deck that follows the contours of the ground, ensuring an even cut regardless of terrain. The high-performance blades provide a superior finish, while the easy height adjustment mechanism allows operators to customize cutting lengths according to their specific needs.

Both the AT and FD models leverage innovative technologies to enhance efficiency. For instance, the AT series incorporates a quick-attach mechanism that simplifies changing attachments, while the FD series includes an adjustable rear roller that gives users better control over cutting quality. Durability is a hallmark of Land Pride equipment, and both series are built with high-quality materials that stand up to demanding applications.

Overall, Land Pride's AT2560, AT2572, FD2560, and FD2572 are indicative of the brand's dedication to delivering high-quality, reliable machinery that meets the needs of both professional and amateur landscapers. With a combination of rugged design, advanced technologies, and user-friendly features, these models contribute significantly to efficient and effective land management operations. Whether smoothing out a lawn or providing a pristine finish on larger properties, Land Pride's equipment stands ready to tackle the challenge. Embracing innovation and performance, these machines represent a commitment to excellence and customer satisfaction in the ag and landscape market.