Land Pride FD2572, at 2560, AT2572 Operating Instructions, Transporting, Pre-Start-up Checklist

Page 15

Land Pride

Table of Contents

Section 2: Operating Instructions

Operating Instructions

Pre-Start-up Checklist

Read and follow the “Safety Rules” carefully.

Oil Level in gearbox

All plugs and caps in gearbox have been replaced and tight- ened properly.

All mower blades, bolts & nuts are tight

Inspect the blades. Make note of the wear to the blades and the sharpness of the blades.

All guards and shields are in place and secure.

Grease PTO shaft and all other grease fittings.

Make a thorough examination of the PTO shafts. Also check the connection to the gearbox and tractor PTO.

Clear the area to be mowed of rocks, branches and other for- eign objects.

1.Clear the area to be mowed of objects and debris that might be picked up and thrown by the mower blades.

2.Grass is best cut when it is dry. Mowing wet grass can cause plugging resulting in grass clumps behind the mower.

3.Grass should be mowed frequently as shorter clippings deteriorate faster.

4.If mowing extremely tall grass, it is best to raise cutting height and mow the area, then lower cutting height and mow a second time at the desired height.

5.Lower mower to ground. Set tractor throttle at approximately 1/4 open. Engage PTO to start blades rotating.

6.Operate only with 540rpm PTO tractor.

7.At first, begin mowing at a slow forward speed and shift up until the desired speed is achieved - maintaining 540 PTO rpm.

8.Mower blades will cut better at a faster rotor speed than at reduced throttle.

9.After mowing the first 50 feet, stop and check to see that the mower is adjusted properly.

10.Do not make sharp turns or attempt to back up while mower is on the ground.

11.Do not engage PTO with mower in the fully raised position. Do not engage PTO at full throttle.

12.After mowing disconnect tractor PTO and follow transporting procedures.

Transporting

!CAUTION

Always disengage tractor PTO before transporting mower to avoid injury from thrown objects or blade contact.

!CAUTION

When traveling on public roads whether at night or during the day, use accessory lights and devices for adequate warning to operator’s of other vehicles. Comply with all federal, state and local laws.

!CAUTION

The mower is wider than your tractor so care should be taken when encountering oncoming traffic and roadside obstructions.

IMPORTANT: Always disengage PTO before raising the mower to transport position.

1.When raising the mower to the transport position, be sure that driveline does not contact tractor or mower. Adjust the tractor’s 3-point hitch lift height so that the PTO shaft does not contact the mower deck. Mower should not be transported without tractor’s upper 3- Point link attached.

2.Be sure to reduce tractor ground speed when turning; and, leave enough clearance so the mower does not contact obstacles such as buildings, trees or fences.

3.Select a safe ground travel speed when transporting from one area to another. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.

4.When traveling over rough or hilly terrain, shift tractor to a lower gear.

!CAUTION

When mowing in sandy soil areas, wear may occur to your mower blades caused from sand erosion. Frequent inspection should be made and blades replaced if damaged

10/11/06

FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Grooming Mower, 3-spindle Table of Contents Safety at All Times Practice Safe Maintenance Important Safety InformationUse Safety Lights and Devices Use a Safety ChainKeep Riders Off Machinery Tire SafetyPrepare for Emergencies Wear Protective Equipment818-555C Safety Labels818-130C 818-556C818-144C 818-142C818-552C 818-540CUsing This Manual Owner AssistanceIntroduction Assembly Instructions Assembly & Set-upGeneral Description Gauge Wheel Assembly Grass Chute AssemblyFinal Inspection Tractor Requirements Driveline InstallationPre-Start Instructions Operating InstructionsChecking Driveline Minimum Length Pre-Start-up Checklist Operating InstructionsTransporting Leveling The Mower Floating & Front To Back Hitch AdjustmentsAdjustments Mower ChuteBelt Tension Cutting Height AdjustmentBlade Sharpening General MaintenanceMaintenance and Lubrication Blade InspectionBelt Tension Blade ReplacementBelt Installation StorageHours LubricationBearing in Blade Spindle Hubs SeasonallyWheel Bushing Martin Wheel Bushing NeilsonOptions Specifications & Capacities FD2560, FD2572, AT2560 & AT2572 3-Spindle Grooming MowerDescription FD2560 FD2572 AT2560 AT2572 Troubleshooting Troubleshooting ChartProblem Cause Solution Torque Values Chart Tire Inflation ChartAppendix Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

FD2572, FD2560, AT2572, at 2560 specifications

Land Pride is a well-respected manufacturer in the agricultural and landscaping equipment sector, renowned for its commitment to quality, durability, and performance. Among its key offerings, the AT2560, AT2572, FD2560, and FD2572 stand out due to their innovation, functionality, and versatility.

The AT2560 and AT2572 are part of Land Pride's series of ATV and UTV attachments designed to enhance productivity in landscaping and maintenance tasks. These implements facilitate tasks such as grading, leveling, and debris management. The rugged construction ensures they can withstand the rigors of tough outdoor environments. Key features include a reinforced frame, adjustable blade angles, and the ability to easily attach and detach from various vehicles. They are designed for optimal performance, providing operators with the confidence needed to tackle diverse terrain with efficiency.

On the other hand, the FD2560 and FD2572 are versatile finish mowers, perfect for achieving a professional cut in various applications, including residential lawns, commercial properties, and sports fields. These mowers are equipped with advanced features like a floating mower deck that follows the contours of the ground, ensuring an even cut regardless of terrain. The high-performance blades provide a superior finish, while the easy height adjustment mechanism allows operators to customize cutting lengths according to their specific needs.

Both the AT and FD models leverage innovative technologies to enhance efficiency. For instance, the AT series incorporates a quick-attach mechanism that simplifies changing attachments, while the FD series includes an adjustable rear roller that gives users better control over cutting quality. Durability is a hallmark of Land Pride equipment, and both series are built with high-quality materials that stand up to demanding applications.

Overall, Land Pride's AT2560, AT2572, FD2560, and FD2572 are indicative of the brand's dedication to delivering high-quality, reliable machinery that meets the needs of both professional and amateur landscapers. With a combination of rugged design, advanced technologies, and user-friendly features, these models contribute significantly to efficient and effective land management operations. Whether smoothing out a lawn or providing a pristine finish on larger properties, Land Pride's equipment stands ready to tackle the challenge. Embracing innovation and performance, these machines represent a commitment to excellence and customer satisfaction in the ag and landscape market.
Top Page Image Contents