Land Pride AT2572, at 2560, FD2560, FD2572 manual Cutting Height Adjustment, Belt Tension

Page 17

Land Pride

Section 3: Adjustments

Table of Contents

5.Set the parking brake and turn off tractor. Remove key from ignition.

6.Adjust the tractor top link in or out to place the upper hitch pin vertically above the lower hitch pin as shown in Figure 3-1, Figure 3-2, or Figure 3-3, to allow mower flotation.

7.Rotate blades in line with direction of travel.

8.Measure the clearance from the cutting edge to the ground at front and rear of the blade. This measurement should be equal or have the blade at the front of the mower not more than 1/2" lower than the blade at the rear of the mower.

Cutting Height Adjustment

1.Using the tractor, raise the mower off the ground and support under it with secure blocking so not to let the mower drift down during maintenance.

2.Holding wheel and yoke assembly up, remove quick- lock pin from top of gauge wheel spindle. Position full length spacers and half spacer as required. All spacers on top of spindle tube allows for approximately 1" cutting height. Adjustments range from 1" to a maximum of 5 1/2" in 1/2" increments. Refer to “Leveling The Mowerpage 14.

!CAUTION

Engage parking brake, shut off tractor, remove key and disengage PTO before making any height adjustments!

Belt Tension

Refer to Figure 3-4:

!CAUTION

Belt drive system under spring tension; use care to avoid bodily harm!

1.To check tension apply force at arrow A. With a tension tester and deflect the belt 1/4". The force required to get this deflection should range from 7 to 10 lbs.

2.To adjust belt tension, adjust eyebolt (#1), as necessary. This adjustment will increase or decrease the tension on spring (#2).

3.Excessive tension on the belt may lead to premature failure of belt and drive components. Excessive tension on the belt may also lead to a safety hazard to the operator or bystanders. Not enough tension on the belt may lead to premature failure of the belt due to excessive slipping.

4.Excessive tension on the belt may lead to premature failure of belt and drive components. Excessive tension on the belt may also lead to a safety hazard to the operator or bystanders.

12732

Belt Tension

Figure 3-4

10/11/06

FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M

15

Image 17
Contents Grooming Mower, 3-spindle Table of Contents Safety at All Times Use Safety Lights and Devices Important Safety InformationUse a Safety Chain Practice Safe MaintenancePrepare for Emergencies Tire SafetyWear Protective Equipment Keep Riders Off Machinery818-555C Safety Labels818-130C 818-556C818-144C 818-142C818-552C 818-540CIntroduction Using This ManualOwner Assistance General Description Assembly InstructionsAssembly & Set-up Final Inspection Gauge Wheel AssemblyGrass Chute Assembly Pre-Start Instructions Driveline InstallationOperating Instructions Tractor RequirementsChecking Driveline Minimum Length Transporting Pre-Start-up ChecklistOperating Instructions Adjustments Floating & Front To Back Hitch AdjustmentsMower Chute Leveling The MowerBelt Tension Cutting Height AdjustmentMaintenance and Lubrication General MaintenanceBlade Inspection Blade SharpeningBelt Installation Blade ReplacementStorage Belt TensionHours LubricationWheel Bushing Martin SeasonallyWheel Bushing Neilson Bearing in Blade Spindle HubsOptions Description FD2560 FD2572 AT2560 AT2572 Specifications & CapacitiesFD2560, FD2572, AT2560 & AT2572 3-Spindle Grooming Mower Problem Cause Solution TroubleshootingTroubleshooting Chart Appendix Torque Values ChartTire Inflation Chart Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

FD2572, FD2560, AT2572, at 2560 specifications

Land Pride is a well-respected manufacturer in the agricultural and landscaping equipment sector, renowned for its commitment to quality, durability, and performance. Among its key offerings, the AT2560, AT2572, FD2560, and FD2572 stand out due to their innovation, functionality, and versatility.

The AT2560 and AT2572 are part of Land Pride's series of ATV and UTV attachments designed to enhance productivity in landscaping and maintenance tasks. These implements facilitate tasks such as grading, leveling, and debris management. The rugged construction ensures they can withstand the rigors of tough outdoor environments. Key features include a reinforced frame, adjustable blade angles, and the ability to easily attach and detach from various vehicles. They are designed for optimal performance, providing operators with the confidence needed to tackle diverse terrain with efficiency.

On the other hand, the FD2560 and FD2572 are versatile finish mowers, perfect for achieving a professional cut in various applications, including residential lawns, commercial properties, and sports fields. These mowers are equipped with advanced features like a floating mower deck that follows the contours of the ground, ensuring an even cut regardless of terrain. The high-performance blades provide a superior finish, while the easy height adjustment mechanism allows operators to customize cutting lengths according to their specific needs.

Both the AT and FD models leverage innovative technologies to enhance efficiency. For instance, the AT series incorporates a quick-attach mechanism that simplifies changing attachments, while the FD series includes an adjustable rear roller that gives users better control over cutting quality. Durability is a hallmark of Land Pride equipment, and both series are built with high-quality materials that stand up to demanding applications.

Overall, Land Pride's AT2560, AT2572, FD2560, and FD2572 are indicative of the brand's dedication to delivering high-quality, reliable machinery that meets the needs of both professional and amateur landscapers. With a combination of rugged design, advanced technologies, and user-friendly features, these models contribute significantly to efficient and effective land management operations. Whether smoothing out a lawn or providing a pristine finish on larger properties, Land Pride's equipment stands ready to tackle the challenge. Embracing innovation and performance, these machines represent a commitment to excellence and customer satisfaction in the ag and landscape market.