Land Pride AFM4214 manual Land PrideTable of Contents

Page 27

Land PrideTable of Contents

Section 5: Maintenance and Lubrication

Blade Removal And Installation

!CAUTION

Depending on blade rotation, bolts attaching mower blades to their respective spindles may be either left hand or right hand. Prevent spindle and/or bolt damage by knowing which hand the threads are before removing and/or tightening any blade mounting bolts.

Refer to Figure 5-2 & Figure 5-3:

1.Verify blade rotation and bolt thread type (right hand or left hand) before loosening center blade bolts and removing blades to be sharpened or replaced.

NOTE: Blade bolt on the left hand deck is right hand threads. Blade bolts on the right hand and center decks are left hand threads.

Refer to Figure 5-5,Model AFM4216 only:

The two outside blade bar bolts (#8) are always right hand threads.

Refer to Figure 5-4 & Figure 5-5:

2.Remove blades by grasping the blade end (#1) with a rag or thick padded glove while loosening the blade mounting bolt (#4).

3.Remove blade bolt (#4) and Washer (#5) from blade being replaced.

4.(Model AFM4216 Only.) Remove two outside bolts (#6) from blade bar (#2).

IMPORTANT: Replace blades with Land Pride blades only.

IMPORTANT: Always install blades with cutting edge facing direction of blade spindle rotation and with wing tips pointing up towards bottom of deck.

IMPORTANT: (AFM4216 ONLY) Loctite is not required if blade (#1) is removed without removing blade bar (#2). However, If blade bar (#2) is removed from spindle shaft (#3), then apply loctite 243 to exteranl spindle shaft threads and to center bolt threads (#4).

5.Reinstall blade (#1), blade washer (#5) and bolt (#4). Care should be taken when installing the blade bolt to not get it cross threaded and to know if the bolt is right hand or left hand. Do not exceed 55 ft.-lbs. of torque on bolt.

6.(Model AFM4216 Only.) Reinstall the two outside bolts. Tighten to correct torque listed in the Torque Values Chart in the “Appendix” section on page 43.

13662

CW Blades Rotation / R.H. Blade Bolt Threads

Top View of Left Hand Deck Belt Drive

Figure 5-2

13661

CCW Blades Rotation / L.H. Blade Bolt Threads

Top View of Center & Right Hand Deck Belt Drive

Figure 5-3

22374

Model 4214 Blade Removal

Figure 5-4

22373

Model 4216 Blade & Blade Bar Removal

Figure 5-5

11/14/08

AFM4214 and AFM4216 All-Flex Grooming Mowers 315-587M 25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents All-Flex Grooming Mowers Table of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Keep Riders Off Machinery Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-339C Safety Labels818-560C 818-019C 818-561C818-130C 818-351C 818-353C 818-337C818-555C 818-552C818-556C 818-045C818-003C 818-513C818-543C 818-229C 818-230C818-335C 818-552C 818-540C Introduction Using This ManualApplication Owner AssistanceLand Pride Service Department East North Street Hardware Torque Information Assembly and Set-upTractor Requirements Tractor Hook-upCheck Constant Velocity Driveline Length Main Driveline InstallationAFM4216 Model Only Gauge Wheel AssemblyHydraulic Hook-up Pull Rope Hook-upBleeding The Fold Hydraulics Table of Contents Constant Velocity Shaft Constant Velocity Driveline AnglePre-Operation Instructions Operating Check ListAFM4214 & AFM4216 Models Operating InstructionsGeneral Operating Instructions Deck Height Adjustments AdjustmentsCutting Height Chart Belt Tension Excessive Belt Tension May Lead toNot Enough Belt Tension May lead to Cutting Blades Accessory Part NumbersAccessories Ball Swivel HitchBlade Inspection MaintenanceMaintenance and Lubrication Servicing Mower BladesLand PrideTable of Contents Blade Options Blade Sharpening Belt InstallationClutch Disassembly, Inspection & Assembly Driveline ProtectionType a Clutches Clutch Run-In Plate Assembly Step Plate Disassembly StepType B Clutch Clutch Run-In Disassembly and AssemblyStorage Tires With Air PressureLand Pride Aerosol Touch-up Paint Driveline Shafts Lubrication PointsHours Driveline Constant Velocity ShaftWheel Bushings Transport Hubs SeasonallyWheel Support Bushings Wheel Bushings Gauge WheelsMower Deck Gearbox RequiredBlade Spindle Bearings Way GearboxTool Bar to Deck Pivot Pin Transport LocksWing Deck Pivot Bushings Wing Flex Pivot Lugs Rear Deck Pivot Half ClampsDescription Specification / Capacity Specifications & CapacitiesAFM4214 Series 14044 AFM4216 Series 13665 Features & Benefits Features BenefitsAFM4214 & AFM4216 All-Flex Grooming Mower Troubleshooting Patches of uncut grass Problem Cause Solution Discharge openingsPlugged Belt slippingAdditional Torque Values Torque Values ChartTire Inflation Chart AppendixTable of Contents Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 88 pages 17.11 Kb
Top Page Image Contents