Land Pride AFM4214 manual Safety at All Times

Page 3

Land Pride

Table of Contents

Important Safety Information

These are common practices that may or may not be applicable to the products described in this manual.

Safety at All Times

Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.

Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

!safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in

the operation, transport, maintenance and storage of equipment.potential hazard to personal safety involved and extra

Operator should be familiar with

all functions of the unit.

Operate implement from the

driver’s seat only.

Make sure all guards and shields

are in place and secured before

operating implement.

Do not leave tractor or implement

unattended with engine running.

Dismounting from a moving

tractor could cause serious injury

or death.

Do not allow anyone to stand

between the tractor and

implement while backing up to the

implement.

Keep hands, feet, and clothing

away from power-driven parts.

Wear snug fitting clothing to avoid

entanglement with moving parts.

Watch out for wires, trees, etc.,

Be Aware of

Signal Words

A Signal word designates a degree or level of hazard seriousness. The signal words are:

!DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded.

!WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.

!CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

when raising implement. Make

sure all persons are clear of

working area.

Turning tractor too tight may

cause implement to ride up on

wheels. This could result in injury

or equipment damage.

Do not carry passengers on

implement at any time.

For Your Protection

Thoroughly read and understand the “Safety Label” section, read all instructions noted on them.

Shutdown and Storage

Lower machine to ground, put tractor in park, turn off engine, and remove the key.

Detach and store implements in a area where children normally do not play. Secure implement by using blocks and supports.

OFF

11/14/08

AFM4214 and AFM4216 All-Flex Grooming Mowers 315-587M 1

Image 3
Contents All-Flex Grooming Mowers Table of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Keep Riders Off Machinery Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-339C Safety Labels818-560C 818-019C 818-561C818-130C 818-351C 818-353C 818-337C818-555C 818-552C818-556C 818-045C818-003C 818-513C818-543C 818-229C 818-230C818-335C 818-552C 818-540C Introduction Using This ManualApplication Owner AssistanceLand Pride Service Department East North Street Hardware Torque Information Assembly and Set-upTractor Requirements Tractor Hook-upCheck Constant Velocity Driveline Length Main Driveline InstallationAFM4216 Model Only Gauge Wheel AssemblyHydraulic Hook-up Pull Rope Hook-upBleeding The Fold Hydraulics Table of Contents Constant Velocity Shaft Constant Velocity Driveline AnglePre-Operation Instructions Operating Check ListAFM4214 & AFM4216 Models Operating InstructionsGeneral Operating Instructions Deck Height Adjustments AdjustmentsCutting Height Chart Belt Tension Excessive Belt Tension May Lead toNot Enough Belt Tension May lead to Cutting Blades Accessory Part NumbersAccessories Ball Swivel HitchBlade Inspection MaintenanceMaintenance and Lubrication Servicing Mower BladesLand PrideTable of Contents Blade Options Blade Sharpening Belt InstallationClutch Disassembly, Inspection & Assembly Driveline ProtectionType a Clutches Clutch Run-In Plate Assembly Step Plate Disassembly StepType B Clutch Clutch Run-In Disassembly and AssemblyStorage Tires With Air PressureLand Pride Aerosol Touch-up Paint Driveline Shafts Lubrication PointsHours Driveline Constant Velocity ShaftWheel Bushings Transport Hubs SeasonallyWheel Support Bushings Wheel Bushings Gauge WheelsMower Deck Gearbox RequiredBlade Spindle Bearings Way GearboxTool Bar to Deck Pivot Pin Transport LocksWing Deck Pivot Bushings Wing Flex Pivot Lugs Rear Deck Pivot Half ClampsDescription Specification / Capacity Specifications & CapacitiesAFM4214 Series 14044 AFM4216 Series 13665 Features & Benefits Features BenefitsAFM4214 & AFM4216 All-Flex Grooming Mower Troubleshooting Patches of uncut grass Problem Cause Solution Discharge openingsPlugged Belt slippingAdditional Torque Values Torque Values ChartTire Inflation Chart AppendixTable of Contents Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 88 pages 17.11 Kb